"Patina" The 1973 CB175 Cafe Racer

Re: "Patina" The 1973 CB175 Cafe Racer


Texasstar said:
Yes


Sent from my iPhone using Tapatalk

Ha, which one? Just test across the bare wire through the resistor cap? I imagine I would get the same as if I had the connector on.
 
Re: "Patina" The 1973 CB175 Cafe Racer

If I put one lead on the metal connector on one end of the wire and the other lead inside the resistor cap I get 4.8 k-ohms.
 
Re: "Patina" The 1973 CB175 Cafe Racer

Is the switch on?


Sent from my iPhone using Tapatalk
 
Re: "Patina" The 1973 CB175 Cafe Racer

Key is off and kill switch is off?


Sent from my iPhone using Tapatalk
 
Re: "Patina" The 1973 CB175 Cafe Racer

I only have a toggle switch. No key. When the toggle is on, the gauge lights come on and everything is activated, including the EI. When the toggle is off, power to the EI is off.

Also, all of these measurements apply when the power cords are disconnected from the coil as well so that's taken into account.
 
Re: "Patina" The 1973 CB175 Cafe Racer

Did you remove the condenser?


Sent from my iPhone using Tapatalk
 
Re: "Patina" The 1973 CB175 Cafe Racer

Running ei right?


Sent from my iPhone using Tapatalk
 
Re: "Patina" The 1973 CB175 Cafe Racer


Texasstar said:
Did you remove the condenser?


Sent from my iPhone using Tapatalk

Oh yeah, absolutely. Condenser is long gone. Like I said, I got a spark before with the old coil, but the jagoff that installed the EI left the ignition on and fried the coil. I've gone over my wiring setup with Sonreir and got his sign off so we should be good there.

EI indeed.
 
Re: "Patina" The 1973 CB175 Cafe Racer

For grins can you disconnect the wires going to the front and back of the coil?


Sent from my iPhone using Tapatalk
 
Re: "Patina" The 1973 CB175 Cafe Racer


Texasstar said:
For grins can you disconnect the wires going to the front and back of the coil?


Sent from my iPhone using Tapatalk

Yeah, they have been disconnected for all of these multimeter readings. My EI wire is disconnected and the white coil wire from my harness as Matt designed it is disconnected.
 
Re: "Patina" The 1973 CB175 Cafe Racer

This makes no sense *scatching head* coil is good wires good ends good but no continuity when connected and tested umm so when the spark plug caps are removed all is good?


Sent from my iPhone using Tapatalk
 
Re: "Patina" The 1973 CB175 Cafe Racer


Texasstar said:
This makes no sense *scatching head* coil is good wires good ends good but no continuity when connected and tested umm so when the spark plug caps are removed all is good?


Sent from my iPhone using Tapatalk

Yeah this is correct. Spark plug caps removed I get 16.6 or so.

That would lead me to think the resistor caps are bad, but when I test them they are just fine.
 
Re: "Patina" The 1973 CB175 Cafe Racer

It really is the most bizarre thing I've seen so far. Are these caps available at auto parts stores? You would think so but I can't find them.
 
Re: "Patina" The 1973 CB175 Cafe Racer

Texasstar said:
This makes no sense *scatching head* coil is good wires good ends good but no continuity when connected and tested umm so when the spark plug caps are removed all is good?


Sent from my iPhone using Tapatalk


Ditto
 
try to get spark with no cap or sparkplug ? just gapping the wire to a ground?
is coil grounded direclty to frame?
 
Re: "Patina" The 1973 CB175 Cafe Racer


Texasstar said:
You can get non resistor caps and run iridium plugs


Sent from my iPhone using Tapatalk

Yeah but I'd like to know what the issue is.

With iridium by the way ( and I haven't done my research) is the objective to get a fatter spark? So more volts and you need less resistance? So no resistor caps?
 
Re: "Patina" The 1973 CB175 Cafe Racer

As of now I don't have a ground on the coil. I just have my white coil wire from my harness and my yellow EI wire. I mean I can throw a ground on there pretty easy but I didn't think my stock coil was grounded either
 
Back
Top Bottom