"Patina" The 1973 CB175 Cafe Racer

Re: "Patina" The 1973 CB175 Cafe Racer

Quick question before I go off on my quest. Seemed like it was running fine yesterday though I didn't pull way hard. How is the timing related to RPM? As in, seems like timing would have to be off at all rpm levels, not just high? Or does it lag so that the higher it is, the more prevalent it is?
 
If it was running fine before, it might be worth checking that the timing plate isn't loose.

But anyway... classic symptoms of retarded timing are as follows:
Excessively hot exhaust pipes
Slow throttle response
Lack of power (especially at higher RPM)

You'll notice they're the same symptoms as many carb issues, which is why a strobe light is such a useful tool. If your timing is correct, you know you need to mess with the fueling. If your timing is out, you save having to pull the carbs apart.
 
Re: "Patina" The 1973 CB175 Cafe Racer


Sonreir said:
If it was running fine before, it might be worth checking that the timing plate isn't loose.

But anyway... classic symptoms of retarded timing are as follows:
Excessively hot exhaust pipes
Slow throttle response
Lack of power (especially at higher RPM)

You'll notice they're the same symptoms as many carb issues, which is why a strobe light is such a useful tool. If your timing is correct, you know you need to mess with the fueling. If your timing is out, you save having to pull the carbs apart.

I'm always about saving time if possible!

Thanks for that explanation Matt. I'll read over the probe manual, get familiar with the system, and do some research.
 
Almost all aftermarket ignition systems will work the same way (and I'd be willing to bet yours is one of them).

They have sensors (usually Hall Effect) on a purpose built circuit board that is either in the shape of the old points plate or is mounted to something that looks like the points plate. Turn degrees of rotation on that plate is what controls the timing advance. Turn it clockwise for more advance or counterclockwise for more retard.

The plate gets screwed down (with some loktite, perhaps?) to keep it from moving around. A loose plate means your timing is wandering.
 
Re: "Patina" The 1973 CB175 Cafe Racer


Sonreir said:
Almost all aftermarket ignition systems will work the same way (and I'd be willing to bet yours is one of them).

They have sensors (usually Hall Effect) on a purpose built circuit board that is either in the shape of the old points plate or is mounted to something that looks like the points plate. Turn degrees of rotation on that plate is what controls the timing advance. Turn it clockwise for more advance or counterclockwise for more retard.

The plate gets screwed down (with some loktite, perhaps?) to keep it from moving around. A loose plate means your timing is wandering.

Good info for sure. The part I am unknowledgeable on is the use of the light and how to use that to diagnose whether Its retarded or advanced. Oh, and the screws were slightly loose. I wouldn't say they were terrible but I got another 3/4 turn out of them on a rubber washer.

Here are some pics if it helps:

eheda4uz.jpg


ymyja7em.jpg
 
Re: "Patina" The 1973 CB175 Cafe Racer

So here is the instructions on how to set the static timing with this system. Since there is a possibility that the plate has moved, I should begin by setting the static timing again, correct?

2u2y5yja.jpg
 
Re: "Patina" The 1973 CB175 Cafe Racer

Also, since this thing is wet on the alternator side, won't I get oil flying everywhere when I crank this thing up without the alternator cover on to check the timing with the light?
 
Re: "Patina" The 1973 CB175 Cafe Racer


1sttimer said:
Also, since this thing is wet on the alternator side, won't I get oil flying everywhere when I crank this thing up without the alternator cover on to check the timing with the light?

And also will running it on low oil levels to set the timing harm things?
 
you are just removing the outer cover
lean the bike over slightly it will be fine,oil will not pour out just some fine spray
only takes a couple tries to get it set
unless your ignition has a way to seperate static from full advance settings then full advance is all that matters, set with the light
put some paint on the marks easier to see
have your fox help you ,make her twist the handle while you are down there at the crank
 
Re: "Patina" The 1973 CB175 Cafe Racer


xb33bsa said:
you are just removing the outer cover
lean the bike over slightly it will be fine,oil will not pour out just some fine spray
only takes a couple tries to get it set
unless your ignition has a way to seperate static from full advance settings then full advance is all that matters, set with the light
put some paint on the marks easier to see
have your fox help you ,make her twist the handle while you are down there at the crank

Will do. She said you might as well call her "broad" instead haha! Too funny.

So I assume I can adjust the plate when it's running? Just loosen slightly and adjust advance, or turn the bike off, adjust and then fire up again.
 
Re: "Patina" The 1973 CB175 Cafe Racer

1sttimer said:
Will do. She said you might as well call her "broad" instead haha! Too funny.

So I assume I can adjust the plate when it's running? Just loosen slightly and adjust advance, or turn the bike off, adjust and then fire up again.
fox is an old school complimet ,broad well that is not so nice
better to shut it off when tweaking the adjust
mark it before you start so you have witness how much you moved it
then when you get it set mark it so you can always get it back same after future removal
 
Re: "Patina" The 1973 CB175 Cafe Racer


xb33bsa said:
fox is an old school complimet ,broad well that is not so nice
better to shut it off when tweaking the adjust
mark it before you start so you have witness how much you moved it
then when you get it set mark it so you can always get it back same after future removal

Makes perfect sense. And that's her new nickname.
 
Re: "Patina" The 1973 CB175 Cafe Racer

In pretty proud of myself here. Followed the electronic ignition instructions (haha) and set my static timing again with the 9V battery as the power source.

The instructions say that the light should stay on the the "dwell" phase and then immediately go off as soon as you enter the full advance marks. The setting initially was at the second full advance mark. I advanced it slightly to just after the first full advance mark (still in between the lines) to get more advance.

The instructions say that anywhere between the lines is correct but I opted for the side with more advance.

This pic shows exactly where the indicator is when the light goes off (spark event)

udamapes.jpg


Here's the way the manual provides power to the unit:

y8y8uvej.jpg
 
Re: "Patina" The 1973 CB175 Cafe Racer

Then I turned the ignition on and plugged int a spark plug. Here's where the spark plug fired: shouldn't it fire right at the F?

5yhu4a8e.jpg
 
only at idle, the other 2 marks to the left,quite a few degrees are the full advance marks,they are the important ones for using the timing light at 3-4000rpms
if you darken in between those two with black sharpie then it is easy to see with the strobe
 
Re: "Patina" The 1973 CB175 Cafe Racer

1sttimer said:
Then I turned the ignition on and plugged int a spark plug. Here's where the spark plug fired: shouldn't it fire right at the F?

5yhu4a8e.jpg
yes for static timing it should fire at the f
so it looks like your timing may be retarded
but those settings are only to get it running the important timing is full advance
 
it looks like you are doing great
i still think it is a good idear to check the timing in a dynamic mode(engine running and reved past 3000)with a strobe
 
Re: "Patina" The 1973 CB175 Cafe Racer

Ok I'll mess with it to get it to fire at the F statically. I am borrowing a coworkers timing light tomorrow to set full advance.
 
Back
Top Bottom