"Patina" The 1973 CB175 Cafe Racer

Re: "Patina" The 1973 CB175 Cafe Racer


teazer said:
Notice how the tacho needle seems to be directly connected to the throttle. On bikes with any sort of flywheel there's a huge amount of lag. Not so with a racing Honda from back then. Cranks were very different to anything we see on the street. Drop revs and it just dies. They have to be kept at crazy revs just to run.

What an awesome sound

BTW, you might want to try a taper on those stacks for even better flow.

If you look at the tach, he's revving that thing at about 13k!! Holy cow. I think the tach reads up to 23k or so...

If I'm reading that right, wow.
 
`that lil 125 screamed !! thanks for that ;D
i had the pleasure of hearing and seeing freddie spencer race the nr500 at lugana
it was the last great honda 4 stroke racing motorcycle engine design,before the current 4stroke motogp formula
oval pistons, 8 valves per piston
2 rods per piston, over 20,000 rpm it was an incredible sound as well :D

http://en.wikipedia.org/wiki/Honda_NR

640px-Ovalpiston.jpg
 
Re: "Patina" The 1973 CB175 Cafe Racer


xb33bsa said:
`that lil 125 screamed !! thanks for that ;D
i had the pleasure of hearing and seeing freddie spencer race the nr500 at lugana
it was the last great honda 4 stroke racing motorcycle engine design,before the current 4stroke motogp formula
oval pistons, 8 valves per piston
2 rods per piston, over 20,000 rpm it was an incredible sound as well :D

http://en.wikipedia.org/wiki/Honda_NR

640px-Ovalpiston.jpg

WOW!! I never even knew anything like that existed...

That does have a unique sound. When you said 8 valves per cylinder without saying it was oval, I have to admit I was quite baffled...
 
honda new the only way to get enuff hp with a 500cc limit 4 stroke against 500cc 2 strokes,was with higher rpms
if the rules would have allowed they proly would have built a v8
piston speed was the issue with a v4 so they did the "impossible" :)
 
Re: "Patina" The 1973 CB175 Cafe Racer

Measure twice, grow once. They look a little squatty, no taper, but I will have to grow them longer to add taper to clear the frame with the bell.

rapugeha.jpg


a7a6ava3.jpg


3yzehyve.jpg
 
Re: "Patina" The 1973 CB175 Cafe Racer


xb33bsa said:
that is very cool and cool tech as well you lucky to be able to play wid it

Yeah that's what I'm hoping for. Things look sooo different from screen to real life. Do you guys think these are machinable or is the flange curl too intense? It's about 279 degrees curl back. Are there lathe tools to turn that?
 
Re: "Patina" The 1973 CB175 Cafe Racer


Highwind said:
where are you getting those stacks from? need some for my CB175

Up a couple of posts you'll see that I drew the up in CAD and prototyped them for fit.


Sent from my iPhone using Tapatalk
 
xb33bsa said:
there would be no reason to have it hollow anyway

Are you saying what I'm thinking. I think I would make a solid ring and weld it to the flare. The void behind the bell will disrupt air flow.
 
i dont think that gap in the prototype he made will disrupt airflow
juts easier to machine it solid
if i was machining them i would start out with thick walled tube ideally to save on machine time
i do think the mouth of the stack should be a very slight taperd funnel but a curved taper like a horn
actually i think machining them from plastic would be a good solution as well
 
xb33bsa said:
i dont think that gap in the prototype he made will disrupt airflow
juts easier to machine it solid
if i was machining them i would start out with thick walled tube ideally to save on machine time
i do think the mouth of the stack should be a very slight taperd funnel but a curved taper like a horn
actually i think machining them from plastic would be a good solution as well
Let me ask you this. If you had a perfect horn shaped stack. How does length affect and let's say a mandrel s- pipe to reroute. All the dirt bikes I have use a boot that goes into a air box. And that boot is crazy shaped. Any benifits from making a air box. ???
 
cafe mike said:
Let me ask you this. If you had a perfect horn shaped stack. How does length affect and let's say a mandrel s- pipe to reroute. All the dirt bikes I have use a boot that goes into a air box. And that boot is crazy shaped. Any benifits from making a air box. ???
length of the horn effects the frequency of the reversion pulse so they say hence some hiperf 4 stroke engines with variable length stacks
2 strokes are a bit different though i do not think they are as sensitive
if you look at any of the gp 2 stroke race bikes they dont go with long stacks just nice short fornnels
basically if you are going to have an efficient filter on anything tho you want to have it seperated from the carbs by a large still airbox this way the air is already past the restriction at the filter and charged to atomspfear ready to pour in when the engine asks
i know 90 degree v twins are quite sensitive if you take the airbox and huge intake pipes off a TL1000 suzuki v twin you lost power that you cannot get back.period
 
Re: "Patina" The 1973 CB175 Cafe Racer


cafe mike said:
Let me ask you this. If you had a perfect horn shaped stack. How does length affect and let's say a mandrel s- pipe to reroute. All the dirt bikes I have use a boot that goes into a air box. And that boot is crazy shaped. Any benifits from making a air box. ???

It's a good question. There is a thread around here about a guy making a collective air box. I wanna say it's for a 350. Maybe Teazer can chime in with the theory, but from what I read as long as you get the air beyond the "lip" the flow pattern in key. The fatter, more elliptical shape of the cross section of the flange at the end the better flow over the flange. It just gives it more of a lead in I think.

Also yeah there should be a taper. My design versus a tapered style is less than a percent difference in air flow over an open carb throat, but the more the better.
 
Back
Top Bottom