Post a pic of your latest purchase

just scored these off ebay they may be going on my Z1 :)
$_57.JPG
 
New stuff, something don't belong, but I do need a way to pay for this shit. ring clamps for the Honda, figure I have a few to work on and the kids is due for an over bore so WTH... brake and oil plumbing, wires, sparky stuff I had for a while now... and the SWEET BSA tank... Had to make a run back to NE and get the hardtail kids way to busy workin to get after it so I'm gonna finish and send tins off to paint.
 

Attachments

  • IMG_20150606_150416099.jpg
    IMG_20150606_150416099.jpg
    4.5 MB · Views: 324
  • IMG_20150606_162305139.jpg
    IMG_20150606_162305139.jpg
    4.5 MB · Views: 336
  • IMG_20150606_162441512.jpg
    IMG_20150606_162441512.jpg
    4.9 MB · Views: 351
  • IMG_20150606_162621473.jpg
    IMG_20150606_162621473.jpg
    3.9 MB · Views: 314
  • IMG_20150606_162813012.jpg
    IMG_20150606_162813012.jpg
    4.5 MB · Views: 345
  • IMG_20150606_143240328.jpg
    IMG_20150606_143240328.jpg
    4.7 MB · Views: 309
I've always liked the shape of A65 engine much better than Triumph ;D
Teardrop shaped cases 'look fast' 8) ;)
 
Tune-A-Fish said:
New stuff, something don't belong, but I do need a way to pay for this shit. ring clamps for the Honda, figure I have a few to work on and the kids is due for an over bore so WTH... brake and oil plumbing, wires, sparky stuff I had for a while now... and the SWEET BSA tank... Had to make a run back to NE and get the hardtail kids way to busy workin to get after it so I'm gonna finish and send tins off to paint.

be careful with those Galfer brake lines, i've had them before and, to put it mildly, they were crap, the ends fell off two of them......i'll not be using their stuff again
 
spotty said:
be careful with those Galfer brake lines, i've had them before and, to put it mildly, they were crap, the ends fell off two of them......i'll not be using their stuff again

That's encouraging... NOT! So what the fuck, Galfer lines are shit then? I don't need the lines popping the crimps that's for sure... Anyone else with poor perf from Galfer lines??? :-\
 
xb33bsa said:
i dont think you want them, 1975 z1903 the stock shocks are pretty lame

Okay... well anyways those big pig back Zooch's won't look right on the Z1 so just go through em, clean em up put a nice gunmetal paint on them and sell em to me for a good DTT price??? and when are I getting a price for the CB shocks 14" eye to eye, I can fudge a little short and put a chunk of ally stock under the swinger mounts if you have a good price on some, I held the swinger back from powder for this reason and I might sand it to natural anyway. Barter is good too if you need/want any parts.
 
xb33bsa said:
sorry ,man , the shocks i have to get top doller :-[

Okay, shocks arnt cheap, not tryin to lowball I know what shit cost. look at what I have into my builds mang :o No worries I can go on eBay too ;D
 
Tune-A-Fish said:
Okay... well anyways those big pig back Zooch's won't look right on the Z1 so just go through em, clean em up put a nice gunmetal paint on them and sell em to me for a good DTT price??? and when are I getting a price for the CB shocks 14" eye to eye, I can fudge a little short and put a chunk of ally stock under the swinger mounts if you have a good price on some, I held the swinger back from powder for this reason and I might sand it to natural anyway. Barter is good too if you need/want any parts.

The look OK, I fitted a pair to my sisters Z1 when I did head bearings. I was really amazed at the improvement in handling (it already had the frame bracing kit installed)
 
Tune-A-Fish said:
That's encouraging... NOT! So what the fuck, Galfer lines are shit then? I don't need the lines popping the crimps that's for sure... Anyone else with poor perf from Galfer lines??? :-\

to be precise with the problems i had...

rear line - when changing the rear tyre, i'd pulled the axle out and was manouvering the wheel out of the swingarm, the edge of the tyre caught the caliper, pulled it, put tension on the line and broke the banjo off the end of the line

front left - while changing the front disc pads, i'd unbolted the calipers and had them hanging on the end of the lines (yes, i know its not a good idea but i think we've all done it.....) went to get the new pads from the bench and came back to find the caliper lying on the floor in a pool of brake fluid, just the weight of the caliper had caused the banjo to snap at the crimp join

to contrast with an old braided ( un-branded ) line i used to have on my old CB750, when i pushed the forks all the way down thru the triple clamps and put mini apes on, that line was just a tiny bit short and actually stopped the forks extending all the way but in all the time i used it, there was never an issue with breaking or failure. again, not ideal practice but by god i was smoking a LOT of pot in those days and such things just didn't seem important
 
crazypj said:
The look OK, I fitted a pair to my sisters Z1 when I did head bearings. I was really amazed at the improvement in handling (it already had the frame bracing kit installed)
yer sister has a Z1 ? what are you saying itsa girls bike ? :D
 
Back
Top Bottom