XS850 - Monoshock & USD Fork (pics pg 13)

If the engine speeds up disproportionately compared to road speed, the clutch is slipping. Usually the problem becomes progressively more obvious the higher gear you are in. Usually the test is to drive up to top bear and give it the gas. Engine speeds up but bike doesn't = clutch slipping.
 
did you do the comp test ? if knot you need to do before you continue to attempt to tune ..if it has a lazy hole which is a def poss-bility then you need to know, now you could be trying to tune busted trumpet
 
xb33bsa said:
did you do the comp test ? if knot you need to do before you continue to attempt to tune ..if it has a lazy hole which is a def poss-bility then you need to know, now you could be trying to tune busted trumpet

Ah ya good call. No, I still need to do that.


Sent from my iPhone using Tapatalk
 
yeah slipping clutch dont do that :-[ you must stop until fixed it can fry the steals as well as the frictions,if it is adjusted with actual freeplay in the system now (freeplay in the cable does not necc. mean freeplay in the actual throwout ) then it needs to come apart
 
clutches are easy take some pics as you take it apart.keep every thing immediately bagged in plastic so you can toss it back in clean as it came out.its a lot of work warshing the parts only cause you dint keep em clean.the steels need to look really good and be surface table flat.frictions likely you need new but if you can still almost dig a fignernail into the friction then you can get away with a light sanding, flat-on flat as glass, with some 180 grit ,just barely scuff them in an infinity(figure 8 ) pattern...warsh em up you can do the same with steels use like 220 grit .....if there is a spec for stacked height then measure,a sparkplug warsher under each spring or even an extra steel can tighten up a still usable worn stack...
do not use any water on frictions :-\ some frictions use a water soluable gloo in the mfg process
i only say this is because otherwise i find very hot soapy water the best thing for final warshing of almost any part on the bike
 
oh and lots of bikes you can do a clutch without even an oil drain,by leaning it over.less mess less work.if the oil stinks like burnt coffee tho,from the clutch :( you proly should put it in yer lawen-mower next oilchange ;)
 
+1 xb. Before you condemn the clutch, make sure you have the throw out adjusted correctly. Of course the cable as well, but the throw-out also has to have a small bit of free play in it so it does not pre-load the clutch. You can see how you could tighten the cable adjuster way too much and it could pull on the clutch enough to partially engage it causing it to slip. The same condition could occur if the throw out is miss-adjusted - even with the cable totally slack.
 
jpmobius said:
+1 xb. Before you condemn the clutch, make sure you have the throw out adjusted correctly. Of course the cable as well, but the throw-out also has to have a small bit of free play in it so it does not pre-load the clutch. You can see how you could tighten the cable adjuster way too much and it could pull on the clutch enough to partially engage it causing it to slip. The same condition could occur if the throw out is miss-adjusted - even with the cable totally slack.

Good call on that. I definitely had the throw out adjusted with no slack, but slack in the line. I'll have to try it again with that adjusted before jumping to any conclusions on the clutch. Thanks!


Sent from my iPhone using Tapatalk
 
I like how this is moving along :)

Clutches aren't bad at all. Just follow the procedure, pull it apart slowly and keep things in order etc and you'll be fine. I think carbs are worse than a clutch. Don't forget to soak the plates the proper amount of time in oil too :) depending upon the instructions of course. Follow what the guys said above and you'll be fine. Go get a $50 compression tester and get it done! You'll use it on multiple bikes over your life, so it's worth it. And don't forget to hold the throttle OPEN when you test :)
 
Definitely going to test it out again after adjusting the clutch actuator before jumping into the clutch itself. I may have overtightened the clutch when I tightened the lock nut on the adjuster. Really appreciated all of the great advice.
 
I heard once that it's bad for an electronic ignition to turn over without a spark plug connected. Is this true? If so, do you disconnect the cdi box prior to checking compression?


Sent from my iPhone using Tapatalk
 
just disconnect the cdi you can even leave the ignition kill switch in off position,and even just jump the solenoid with all other power disconnected at the main bat + terminal... a remote starter switch ,an old school common tool for auto work, is handiest solutuin
 
If you jump it at the solenoid do you still have to disconnect the cdi?


Sent from my iPhone using Tapatalk
 
Hey if the key is off, the ignition is off. Hard to injure it when it is off! If you are jumping it at the solenoid, you are bypassing the entire electrical system so as far as the jumping is concerned, the rest of the system is irrelevant. Doubt the cdi could be harmed anyway - the COIL on the other hand is a different story. Lots of energy stored up in the coil. Tell it to discharge by breaking the primary windings, the energy very much wants to go somewhere - I mean, it's willing to ionize the dreadfully hard to ionize material between the spark plug electrodes in the combustion chamber at high temperature and pressure at ridiculous repetition all day long. Make that gap too wide by removing the plug and all that energy may find an undesirable (and permanent) path to ground along another route.
 
Well, I disconnected the cdi, so power shouldn't (?) have been running to the coils. Regardless... I got the compression test done. Results are interesting.

#1 = 140psi
#2 = 130psi
#3 = 130psi

By the book, this is all good. I guess it makes sense that 1 is high with the right exhaust valve? Regardless. This all seams good.

Sooooo. I guess my rich symptom in 1 HAS to be fuel related. ???


Sent from my iPhone using Tapatalk
 
That small variations in comp can be disregarded i think. How about you put some fuel system cleaner in the tank and just ride the shit out of it? :)
Redline has a good product, i use it for all my machines.
Cleaned out the carbs on my 750 to a near optimum performance.
And its a lot more fun cleaning carbs while you ride!
 
Back
Top Bottom