Follow along with the video below to see how to install our site as a web app on your home screen.
Note: This feature currently requires accessing the site using the built-in Safari browser.
We noticed you are blocking ads. DO THE TON only works with community supporters. Most are active members of the site with small businesses. Please consider disabling your ad blocking tool and checking out the businesses that help keep our site up and free.
I've got a 1981' Honda CB125S USA model that I'll be installing a fully rebuilt high performance engine into.I like that the 1st generation CB125S models came stock with the tachometer and I want to install a factory Honda cable drive tachometer from one of the old style CB125S that I have.I...
I've been trying to find a fuel cap that isn't available anymore for my 1980 Honda CM400E.The same cap will fit the small gas tank opening of the 78' CB400T 'hawk', 1980-82' CB125S,etc. This cap is smaller than most other Honda caps and comes with a chain that keeps the cap from coming out all...
I picked up an old CB125 that's been sitting outside for a few yrs. and I'll be getting the frame and swingarm sandblasted.What's the toughest gloss black rattle can paint I can get to spray paint it so it'll resist scratching,etc. better than common Duplicolor enamel or other paint ? I need a...
I just got a 'rusty' ole bike from a guy up in NY. off CL,bit's n' pieces.. but 90% there.The man isn't the last registered owner,it was an abandoned bike at one of his buddies rental houses or something.
I'm in PA. & don't reside in VT.,have any of you done the VT. reg. thing out of state? How...
I bought an early XR200 bottom end and the eng.# is: ME02E-5300285
I know there must be a way to look it up online and i think I found one site a while back but can't find it anymore.I'm just guessing that this engine comes from a 1982' XR200 w/ twin rear shocks..
I have my early 80's XR200 that I'm doing a full engine restore to and along with that I'm considering the challenge of straightening this bent alloy 'fin' on the chaingaurd side of the left crankcase.I have located this motor bottom-end from someone and purchased it for a fair price and this...
I've got a little 81' CB125S and I'm installing an XL185 engine and later an XR200 engine(all w/ the 2nd generation 2-piece cylinder head engine) plus improving the suspension,etc. I like what they do in Aus. w/ 'bucket racers' etc. but here in the US the little Honda engine isn't as popular as...
Hi,
I have a little CB125S that I'll be installing an XR200 engine in and was looking around on ebay for a pr. of shocks.. I just didn't want to go 'china' and noticed a few threads from member here 'xb33bsa' about nice rear shocks that he built & set-up nice so I got in touch w/ him and he had...
I've got this little 81' CB125S that I'm installing an XR200 engine into and want to stay w/ the low/bottom 'CB' street exhaust.I had a muffler place build me a head-pipe w/ 1.5" pipe and they used a hydraulic tube bender that is common to pipe bending automotive exh. which did bend the tubes in...
Hi, I'd like to find a pr. of used vintage European style riding boots size 12W that have thin type soles and separate heels that can be repaired/replaced.
I need about 4.5" across the widest part of the front leather uppers where my toes are,the ball of the foot;the front of my foot is wide but...
I have a 1986' VFR700F/840cc Interceptor engine w/ 614 original break-in miles after full high performance build by a race bike builder out in CO. I've have it in it's own custom sealed crate but have removed the top and sides to keep the size of it small enough to save $ on freight.The engine...
Hi,
I'm enjoying the forum and want to wish everyone here a Happy Thanksgiving.I hope all of you enjoy your families and loved ones.Drive Safe and don't fill up too much before a long drive.. it makes me fall asleep when I do :D
Hi,
I'm looking for someone over in Europe or Italy who may have parts for a 1983-84' Honda CB125X.
The bike is a very nice sporty looking version of the American/USA spec. CB125S from 76-82' w/ the 2-piece cylinder head.
The 83'-84' CB125X was not imported to the USA and it's the only model...
Hi,
I've got a 1981' CB125S and I'm going to install an XL185S engine which is a bit more power/flow for the stock exhaust.I've got a good muffler that I'm going to use and want to find a workman who can bend me a length of 1 1/2" o.d. exh. pipe(this has the desired 1 3/8" i.d.,the pipe is...
I wonder if the Pro Honda SS8 10wt. suspension fluid is made from ATF(automatic trans. fluid) ?
I only ask because it's red in color ::) What do I know ???
I've got a 1981 Honda CB125S,the first yr. for CDi ign. but it's still a 6vt. system.I'd like to get an electronic tach. for it and wondered if anyone makes a 6vt. meter ? round analog readout ?
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.