Follow along with the video below to see how to install our site as a web app on your home screen.
Note: This feature currently requires accessing the site using the built-in Safari browser.
We noticed you are blocking ads. DO THE TON only works with community supporters. Most are active members of the site with small businesses. Please consider disabling your ad blocking tool and checking out the businesses that help keep our site up and free.
I just finished an engine rebuild and got the bike running through idle to full rev with no problems. One thing I am having an issue with is on deaccerlation I get tons of popping. The plugs don't look lean or rich but will post a pic to show the group.
I am running Mikuni vm30 with filters...
Hello,
I purchased a 1981 RD350LC that had been sitting for 6 years. Cleaned up the carbs, put new throttle cable / oil pump cable. The jetting is all stock and idles and runs great through the gears but I never seem to hit the power band in any gear. I checked the plugs and they are...
I have for sale my 1969 Honda CL350 Cafe Bike.
Ebay Listing:
http://www.ebay.com/itm/1969-Honda-CL-/222464750734?hash=item33cbeeb48e:g:HrYAAOSwU8hY5XkS&vxp=mtr
Please DM with any questions.
Thank you,
Miguel
Hello,
Does anyone have measurements for a Honda CB350 Fat Cam? Just wanted to check my cam and make sure its to spec or if I need to replace. Also with the specs what gets meausured, the lobes?
Any help would be appreciated.
Miguel
Hello I am working on a rebuild engine and have the bike finally complete. Issue that I am running into is when the bike is cold it shifts fine from 1st, N, 2nd gears. When I ride the bike and get it warmed up I have a hard time getting the bike back into 1st gear. Even rolling or at a stand...
Hello guys,
So been trying to get this 1982 CM200T bike of mine running again. My friend had left the key on and drained the battery which I assume also fried the coil. I tested the coil and had just under 1 ohm. I also noticed the CDI unit was fried as well as the connectors were all black...
Does anyone have an online source for wiring 16 gauge that has a selection of colors that can be used to create a Honda Harness CB350? Not able to find a source online that carries 2 color wire.
Thanks
I have a CB350 that has been producing a ton of vibration on the right side clip ons. This is a complete bike done from ground up. I started off with the original front end with drum brake and had the vibration. I then upgraded to disc brake and changed up forks, wheels, steering stem and...
There are a few posts around peoples VM30 setups on CB350 that I figured it would be great to get others to post what worked for them.
Here is what I got working so far on my 1969 Honda CL350:
Location: Central California
Stock Pipes
Velocity Stacks
Slides: 2.5
Needle: 6F4
Needle Jet: 176-P4...
I ordered new friction plates for my Honda CB350 but was wondering if I could sandblast the steel plates since they have slight rust to them. Would it just be best to buy new ones and are they still available besides looking on ebay?
Thank you
Hello,
I was hoping maybe someone can help with a question. I am running a fat camshaft on my Honda CB350 but want to make sure that I should be running the 286 marked Sprocket. I am also wondering where I can find one as it been really tough to source on ebay.
Does anyone have one they want...
Does anyone know where I can get a new camshaft for my Honda CB350? I know Bore Tech offers high performance cam upgrade on core. Curious if cams are even still available for CB350?
Also need Rockers as mine are pitted pretty bad.
Any information would be helpful.
Thanks
I built a 1969 Honda CL350 Cafe Bike with Clip Ons. The throttle side vibrates so much on the grip that its so uncomfortable to ride. The left side is fine with no vibration. I thought maybe it had to do with the front suspension but I updated from Drum to Disc with new tire, forks, Steering...
Hello,
I had a timing light question if someone can help. I hooked up a strobe timing light to the left spark plug wire and started the bike up and when i run the bike at idle the LF mark lines up with the timing mark. Is that correct?
I was able to pick up 2 bikes from a guy and one of the motors is completely seized and has been sitting for 20 years. I was able to remove the head but having a really hard time getting the pistons out. I am not able to crank the motor over at all. It is completely frozen. Just wondering if...
I am not sure what this problem could be other than it might be the actual gears inside that are stripped. Check out this video of mine showing the problem. Basically when I turn the kick start shaft quickly it just slips but when I go slow it works...
Hey guys.
So I wrapped up my first cafe bike build. You can see pictures here:
http://diadelosmotos.tumblr.com
I finally got my hands on another project bike, but this time it was a barn find. The bike is complete and has compression but probably hasn't been started in 20 years. The last...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.