My CB750 Project(reassembly has begun!)
- Thread starter LuckyLuci631
- Start date
LuckyLuci631
Active Member
Re: My CB750 Project(new pic) need some help
nope been torchin and blastin all day still wont budge picked up a new impact driver today gunna give that a try in a few min such a PITA! im trying to take my time and avoid using the drill
nope been torchin and blastin all day still wont budge picked up a new impact driver today gunna give that a try in a few min such a PITA! im trying to take my time and avoid using the drill
LuckyLuci631
Active Member
Re: My CB750 Project(new pic) need some help
Success!.. got them out but i cant seem to get the countershaft bearing holder off? is it supposed to come off and whats my best approach to splitting the cases(everything is unbolted i believe)
Success!.. got them out but i cant seem to get the countershaft bearing holder off? is it supposed to come off and whats my best approach to splitting the cases(everything is unbolted i believe)
LuckyLuci631
Active Member
Re: My CB750 Project(new pic) need some help
good still confused on the countershaft bearing holder...havnt gotten a chance to work on it(too much real work) and i still need a little guidance for splitting the cases
good still confused on the countershaft bearing holder...havnt gotten a chance to work on it(too much real work) and i still need a little guidance for splitting the cases
LuckyLuci631
Active Member
Re: My CB750 Project(new pic) need some help
never mind i got it just had to pull a little harder and someone help me with how i should start to split my cases i dont want to mess anything up
never mind i got it just had to pull a little harder and someone help me with how i should start to split my cases i dont want to mess anything up
tweakin
Beer and Grease
Re: My CB750 Project(new pic) need some help
I took this from another post so I can't take credit but this should help out, But this is a great description of how I do it.
Get all the bolts out then flip upside down.
"You shouldn't have much trouble splitting the cases, if all the bolts are out. There's 25, 26 or 27 6mm and 8mm bolts, depending on year, and 10 8mm nuts with washers. Don't miss the one in the starter area, and three across the back, and two to four in the countershaft area.
Also, remove the gearshift arm and the mainshaft bearing retainer. Finally, this picture should help with a pry point: it won't take bu a single jerk on this shaft, levering against the bottom case, to pop them apart if all bolts are out. The gasket compound (sealant) doesn't have a lot of grip." Hondaman
I took this from another post so I can't take credit but this should help out, But this is a great description of how I do it.
Get all the bolts out then flip upside down.
"You shouldn't have much trouble splitting the cases, if all the bolts are out. There's 25, 26 or 27 6mm and 8mm bolts, depending on year, and 10 8mm nuts with washers. Don't miss the one in the starter area, and three across the back, and two to four in the countershaft area.
Also, remove the gearshift arm and the mainshaft bearing retainer. Finally, this picture should help with a pry point: it won't take bu a single jerk on this shaft, levering against the bottom case, to pop them apart if all bolts are out. The gasket compound (sealant) doesn't have a lot of grip." Hondaman
LuckyLuci631 said:
LuckyLuci631 said:
LuckyLuci631
Active Member
Re: My CB750 Project(new pic) need some help
yea i have the service manual but it doesnt seem to say which way the cases should be(bottom up or bottom down) and a good place for a pry point but thanks to tweakin i should be able to figure it out and seemingly the general consensus is that the cases should be upside down
yea i have the service manual but it doesnt seem to say which way the cases should be(bottom up or bottom down) and a good place for a pry point but thanks to tweakin i should be able to figure it out and seemingly the general consensus is that the cases should be upside down
LuckyLuci631
Active Member
Re: My CB750 Project(new pic) need some help
so after taking my time i have sucessfully split the cases without damaging anything
not as hard as i thought..thanks to all that are walking me through this so far
so after taking my time i have sucessfully split the cases without damaging anything
not as hard as i thought..thanks to all that are walking me through this so far
LuckyLuci631
Active Member
Re: My CB750 Project(updated) new pics
so its been a few weeks since ive updated...since my last post i have inspected and checked all my internals..everything seems good, i second guess myself because this is my first build ever, and reassembly has begun, waiting on some odds and ends to come in the mail, hopefully will make some good progress this weekend i intend to have the motor completely reassembled within the next few weeks
so its been a few weeks since ive updated...since my last post i have inspected and checked all my internals..everything seems good, i second guess myself because this is my first build ever, and reassembly has begun, waiting on some odds and ends to come in the mail, hopefully will make some good progress this weekend i intend to have the motor completely reassembled within the next few weeks
S
sovern
Guest
get on it scat, show some of that paint. need to get this beauty done, I'll be home 2 days before christmas until newyears day. idk if you want to get anything done than. let me know.
