69 Honda CL450 Scrambler Restoration

Being a glutton for punishment, I then moved on to try to remove the dent in my gas tank. There is a pretty uniform dent at the "right knee" spot on the tank. The local paintless dent repair guy wanted $200 to fix it but wouldn't guarantee he could do it. I figured I could find a way to get the dent out so I picked up a rubber bladder sink unclogging device from Lowe's. I used a bike patch to plug the bleed hole at the end of the bladder, fed it into the tank, and turn the water on. It initially popped the dent out about 50% of the way. I was going to grab something to tap the tank around the dent to influence it to pop out when the bladder blew open. It was crazy loud when it let go. Probably should have left the bleed hole open. Fail.

Realizing that today wasn't my day, I'm going to take the afternoon off from working on the bike.
 
That was still a good idea. You are halfway there. ..LOL, maybe the dentless repair guy will reduce his price to $100 now that you did half of it...
 
It's been a while so I felt it necessary to update the work I've completed on the bike. I've been traveling every weekend and playing catch-up all week in between trips so I haven't really made much progress.

I was able to pull the dent out of the tank using a glue on dent puller from HF. It didn't work 100%, but it's good enough for now. I also touched up some of the scratches/chips in the tank, and fixed a few spots on the stripes. The tank and side covers had some overspray on them from something the PO did. I wet sanded with 1000/1500/2000 then went to the extra cut rubbing compound, regular rubbing compound, and finally a machine glaze. The tank isn't 100%, but I just couldn't justify sanding all of that good original paint.

I was able to construct a throttle cable and speedo cable this weekend using some some pieces from the motion pro hardware I have along with the stock components and a few barrel ends from Flanders Cables. So far so good, until I realized that I had ordered conduit that was too small to make the new brake and clutch cables. That's another 5-8 days of waiting to get that done.

I picked up a new battery today and was able to statically time my points/plate. I kicked the bike over a few times and verified I had spark. Oiled up the Uni-Filters, installed, and hung my side covers.

The tank and seat will go on tomorrow. I need to polish my exhaust and then I'm hoping to get around to putting gas in it and firing it up for the first time.
 

Attachments

  • IMG_20130525_204750_422.jpg
    IMG_20130525_204750_422.jpg
    838.8 KB · Views: 367
  • IMG_20130525_090445_282.jpg
    IMG_20130525_090445_282.jpg
    1.1 MB · Views: 398
I was able to install the tank, fuel line plumbing, seat, new battery, and exhaust on Sunday, along with some fresh gas and engine oil. I kicked this thing over for a while - there were a few times where it sounded like it wanted to go, but just ended up with a tired leg.
I tried again yesterday morning - with the throttle cracked half open, it fired and ran for about 1.5 seconds. That was it. Now it just kind of pops in the exhaust.
 
Make sure the coil wiring is correct and going to correct side. Might also be the point advance cam being on 180 degrees out. Check timing as well, these bikes really can be picky about it.

Of course make sure you have fuel getting into the cylinders. If the bike is firing on the exhaust stroke you will get fuel wet plugs and a bang out the exhaust.
 
I gave the bike a few more kicks after work today and didn't get anywhere. I'll give you guys a rundown of what I know so far -

- It took me a while to get the cam timing right, but I'm pretty sure it's spot on. I went through the trouble of ordering a second cam chain because I didn't like the first one. I posted pics previously in this thread - See reply #44, not #40.
- New universal coils mounted in the stock coil mount location. The frame was powder coated, so I ran a seperate ground wire from the new coil mount I fab'd back to the frame ground below the carbs. Continuity was checked and good from the coil mount to the battery
- New battery, charged.
- I followed the static timing procedure posted on Honda Twins to set my static ignition timing. I set the proper gap on each point, then With my test light connected to the yellow coil lead (coil connected to my LEFT cyl spark plug), I set the point plate such that the test light lit just when the mag "LF" mark reached the pointer. Then, with the test light connected to the blue lead (coil connected to my RIGHT cyl spark plug), I set the point gap such that the test light lit just when the mag mark "F" reached the timing mark.
- Carbs were soaked and cleaned. Rebuilt with a rebuild kit that included new jet (stock sizes). I believe my right cyl float level needs to be adjusted. I'm running clear inline fuel filters and the right cyl filter is dry after sitting for 5 days.
- I checked the compression tonight with a known good gauge - 120psi in both cylinders after numerous kicks with the throttle open. I'm disappointed in the 120psi - I had 150psi before I tore this engine down. I reused the pistons and installed new rings. I'm hoping that after I run this and the rings get a chance to seat, the compression number will come up. Regardless, 120psi is enough to run

I can't work on the bike until Sunday. I plan to first check my static initial timing again to make sure the points plate did not rotate. I know that things can be installed 180deg off, but can it still seem to be timed "properly?"

As always, I appreciate any help or suggestions. I'm pretty excited to get this thing running so I can start fine tuning things.
 

Attachments

  • IMG_20130526_124445_118.jpg
    IMG_20130526_124445_118.jpg
    1.4 MB · Views: 390
Well, its a lost cause, just let me give you about 400 bucks for it and I will take that misery off your hands. ;) Damn that thing looks pretty, I wish I had mine finished being painted. MAYBE this weekend.

Anyhow, MY thoughts, Coils don't need to be grounded, they are grounded through the points. The circuit is completed when they close. Sounds like you have a good static time, the issue is if it is on the right or the wrong cycle. The advancer cam can be put on 2 ways, I have made that mistake many times. Yes you can set points to the correct setting but be 180 degrees out.

Compression MIGHT get better as you run it in but it should be much higher than that on a fresh re-ring if you made sure your gaps are correct and placed so they don't line up. Could be that your valves are slightly too tight and holding the valves open.

The fuel will move out of the lines, the valves in the carbs are not a perfect seal. Be religious about turning the petcock off when you are done riding. I try to flip it about a block out from the house just to run the fuel out. Right side is the first to run out of fuel since it has the shortest line. IF you get crank case full of fuel do not try to start it or kick it or anything. 450's need good oiling and fuel thinned oil will destroy them before you can get it shut down.
 
I got to work on the bike today and check a number of things that could be contributing to my problems. I pulled both valve covers and inspected my cam timing and valve lash. The cam timing was dead on. My valve lash was at .003" so I adjusted it back to the spec at ~.0012 (my lowest feeler gauge was .0015". With the lash looser than the specs, I can rule out tight lash as the cause for the low compression.

I then decided to pull the points plate and advancer mechanism and I'm glad I did. Once I pulled the points plate I found a bunch of metal shavings. Turns out, the allen head bolts I used to mount the LH Ex cam bearing were being rubbed the advancer mechanism as it rotated with the ex cam. I also think I had my advancer mechanism on 180 degrees off. The smaller of the 2 notches was engaged in the cam pin. I found some new pan head machine screws to replace the internal hex bolts and put things back together with the larger notch of the advancer installed over the cam pin. I then static timed the bike.

I had the carbs off, so I used the "credit card" method to adjust my float height. I'm waiting on the rubber parts to refresh my petcock and then I'll put it all back together to see if it'll run this time around.
 

Attachments

  • IMG_20130602_122034_780.jpg
    IMG_20130602_122034_780.jpg
    931.4 KB · Views: 391
  • IMG_20130602_122056_147.jpg
    IMG_20130602_122056_147.jpg
    746.4 KB · Views: 379
That's funny, I had the exact same problem. Where did you get the bolts from?
 
I think your bike is unrepairable. I'll send you $100, take if off your hands and you can cut your losses. Obviously a money pit from hell....Despite it looking gorgeous, you really need to think about getting a new modern bike, using the $100 I'll send you for this one..... ;D

Otherwise, if you decide not to take my more than generous offer, I know you will have her road worthy before you know it.

That is simply a beautiful motorcycle... 8)
 
frogman said:
That's funny, I had the exact same problem. Where did you get the bolts from?

I picked them up from eBay, but I can't recall the seller right now. I'm happy with the set and how they looked, but I was disappointed to find that the engine bolt kit didn't include enough bolts to do the entire engine - I had to order a few extra bolts to do the cam caps.
 
mydlyfkryzis said:
I think your bike is unrepairable. I'll send you $100, take if off your hands and you can cut your losses. Obviously a money pit from hell....Despite it looking gorgeous, you really need to think about getting a new modern bike, using the $100 I'll send you for this one..... ;D

Otherwise, if you decide not to take my more than generous offer, I know you will have her road worthy before you know it.

That is simply a beautiful motorcycle... 8)

Thanks - the pics make the tank look a little better than it really is. Up close, you can see a few of the paint imperfections that I wasn't able to cover up. Buffing the tank and tins really brought out the beauty in Honda's Candy Blue color though.
 
Guys - I had a big night last night.

First, I figured out why my horn and elec start weren't working. I replaced the rubber bar mount isolators with a set I had kicking around from my Honda MX bikes. This meant that there wasn't elec continuity between the bars and the frame. I made a jumper than runs from the bar mount to the top triple clamp steering stem pinch bolt. Elec start works!

Second, after working through my valve timing, lash, and swapping my points advancer 180 deg, I was able to fire up the bike and run it for a few minutes. I didn't have the tank on it, so I was only able to run it for about a minute or two each time I filled the fuel lines up with gas.

Some things I noticed with it running -
1. Blue smoke - I'm hoping that once I get the tank on it and can get things warm, this may burn off. Otherwise, I may have the answer why I only have 120psi of compression in each cylinder.
2. It sounded like the cam chain was slapping the engine case. This blows my mind, because the timing chain was SO tight when I installed it. I'll adjust the tensioner again.
3. The bike would only start if I gave it about 1/4 throttle or more.
4. Bike wouldn't idle - I'm not too worried about this right now, since I never really got it warm.
 
The proper clutch and brake cable conduit came in the mail today so I fired up my redneck solder pot and finished making cables for the CL high handlebars.

Since I wasn't changing any lengths, this was pretty straight forward. I cut the old handle end barrel off the existing cable. When cutting this off, be careful to cut it square. You don't want to fray the end yet. I then measured the old conduit and cut the new conduit to this length. I used a drill bit to clean up the ID of the conduit. I installed the new ferruls on each end, ran the old cable threw the new conduit, and installed a new barrel end sized to fit the proper lever. I clamped the cable in my bench vise and used a spring loaded center punch to splay the cable end that was to be soldered. Add a little flux to the end as well.

I was able to find silver solder at the local Home Depot. I also picked up a new 3/4 iron pipe plug as well and installed it in my solder pot holder. I started the propane torch and monitored the solder pot temp using the K-type thermocouple that I have for my multimeter. I wanted the temps to be around 550F, so I adjusted the flame and distance of the propane torch to the underside of the solder pot. Once things were around 550, I dipped the first barrel end + cable into the pot. You only want to go as far as the top of the barrel to ensure that solder gets into the barrel through hole. Any higher and the heat can embrittle the cable, making it hard to articulate though the lever motion. Leave the barrel and cable immersed in the hot solder for 10-15 seconds. You want everything to get up to temperature and ensure a good solder joint.

Pull the cable/end out and inspect. If you get a bunch of solder on the OD of the barrel that looks like crap, that indicates a cold joint. There will be excess solder around the outside of the barrel that you want to look like it had kind of flowed and oozed around it.

From there, grind and file the barrel to get it to fit into the lever pocket. I gave each of these cables a good yank when clamped in the vice - likely a 60 or 70 lb load, which should be plenty for a clutch and frt brake lever pull.

Disclaimer - Since making brake cables should be left to the experts, this post should be considered reference only. I'm posting the steps I took to share my experience. By no means should any of this be considered a sure fire "How To" - You and only you are responsible if you make your own brake cables and they fail.
 

Attachments

  • IMG_20130604_191111_906.jpg
    IMG_20130604_191111_906.jpg
    637.6 KB · Views: 354
  • IMG_20130604_191141_250.jpg
    IMG_20130604_191141_250.jpg
    651.3 KB · Views: 374
I finished rebuilding my petcock and got the bike running on Sunday. The elec start doesn't seem to spin the bike fast enough to start it. I can get it running with the kickstart and some throttle input. Once running, the bike won't idle, even when warmed up. I added some idle screw to each carb, which seems to help, but I still don't have the ability to walk away from the bike and let it idle. It's also puffing blue smoke pretty bad which isn't good.
I originaly had the air screws backed out 1.5 turns each - I gave each of them an additional half turn out, which seemed to "hang the idle" after blipping the throttle. I'm going to try going the opposite way with the air screw next time I fire it up. Note - I'm running stock jetting.
 
Thought I'd share a little bike porn
 

Attachments

  • IMG_20130609_105415_405.jpg
    IMG_20130609_105415_405.jpg
    869.2 KB · Views: 400
Great work man. Have you made any progress on getting the bike to idle better? Sounds like you're having similar issues as I am right now.
 
Back
Top Bottom