CB125s build. "The Dishwasher"

Re: CB125s build. questions abound!

We'll see if I can go lower /w clip-ons once I have the rearsets done in a way that I like.


That said, I can't go as low as my aprilia. The goal is to have it actually tolerable around town ;D


As for the chain guard, I'm pretty sure you could just hammer a dent into it and make it work (it's super close to fitting)


I just don't want to damage any original parts right now, so I'm going to just modify one from another bike to fit.
 
Re: CB125s build. questions abound!

Picked up a new battery, got my 12v box in, all my carb bits and pieces, fork seals, some new gaskets, air filter, and ordered a set of michelin gazelles.


This weekend will be spent trying to get everything running perfectly, and if I can, tearing into the 12v conversion.
 
Re: CB125s build. questions abound!

Hey there. looking good so far. I have 2 125s. 1 i ride all the time the other has yet to be fixed up and ran. Like you I have had all kinds of issues getting it to run right.
Ran rich, floats were shoot. Was surging at part throttle, cruising speed and would die at stop lights after warming up or after multiple down shifts. Turns out dropping the needle 1 notch to lean out the bottom end fixed the problem. I guess what happens is the needle jet orifice gets worn out over time and causes it to run rich so dropping the needle compensates for the worn out area. Im running an 86 main and it does great. I feel like the power is not there on the full throttle range so im going to bump up to a 90 or 92 main.
I am planning on converting to 12v but im going to try it on my 78 125 first as it will not be stock at all. I have read up on it quite a bit. You can just swap on a 12v battery and put on a 12v reg/rec and change out all your lights. BUT the bike does not put out that much power that if you ride in stop and go it should slowly drain your battery so be sure to charge it up when its at home. The other option is to rewind the stator. This gives you more power because the original way it is wound you are not using the whole stator to charge the battery only part of it so by rewinding it you use the full potential. The other way is to swap in a stator from a different bike that is 12v. I can not verify that this works or if the stator will fit but that is the route im going to go on my 125. I love the little bikes. I just sold my 750 and i ride my 125 all the time now. The forks on these were different then any other fork i have rebuilt so if you get stuck dont force it. I ruined 1 fork in the process but i learned from it, lesson is DO NOT take the bolt at the very bottom end of the fork off it stays there and does not need to come off.


What did the tires end up costing you?
check these guys out.
http://thekatros.blogspot.com/
 
Re: CB125s build. questions abound!

yeah, the stator rewind is what I'll just pay someone to do if this doesn't work out.


tires were ~$27 apiece, tubes were about $11 apiece. after tax and mounting, about $85.
 
Re: CB125s build. questions abound!

I'm also running gazelles right now mainly because of the price. I ordered from motorcycle superstore and paid right at $40 for the set. They're decent tires and so far. I'd buy them again but they've only been on for a month of so. You guys keep us updated on the 12v swap, because the 6v system is my main gripe about this bike and I would love to know how to swap over. The cb125 group has some good info about the swap, but I can't ever seem to find anything definite there.
 
Re: CB125s build. questions abound!

got the carb seals done, and it runs like a stabbed rat!


I am curious about changing my front brake into a hydraulic disc. Are there any options for kits out there?
 
Re: CB125s build. questions abound!

Shit man, are you going to address every weak link in this bike? I like where your head is. I'll be watching to see if this can be done as well. My cable actuated disc sucks more than an 8 pound Oreck.


Oh, and I have no idea what kind of swap can be done.
 
Re: CB125s build. questions abound!

I haven't got around to it yet but I bought a cb550 caliper and arm that I'm going to try and machine down to fit. If n.ot I may try a custom arm with the 550 caliper
 
Re: CB125s build. questions abound!

DirtyFrank said:
Shit man, are you going to address every weak link in this bike? I like where your head is. I'll be watching to see if this can be done as well. My cable actuated disc sucks more than an 8 pound Oreck.


Oh, and I have no idea what kind of swap can be done.


The goal is to have a "stock" custom bike. Lots of improvements, but nothing that really makes it scream custom build. And it's all going on in the backyard, so I'll be limited with my custom parts.


The proper hydraulic disc brake is mostly about safety. As it is, 90% of my braking force comes from the rear. That just doesn't sit well with me.
 
Re: CB125s build. questions abound!

ripped off all my fenders and did a simple wiring of my turn signals, took off the reflectors on the forks. It's starting to look like a proper cafe bike now.


next step is a seat, 12v conversion, rearsets, and taillight.
 
Re: CB125s build. questions abound!

New seat is in the mail, as is my taillight. Going to try wiring it up with the 6v system. One thing at a time. Then comes the brake upgrade (I'm thinking switching to a wheel from a cb550 or the like)
 
Re: CB125s build. questions abound!

honeybadger said:
New seat is in the mail, as is my taillight. Going to try wiring it up with the 6v system. One thing at a time. Then comes the brake upgrade (I'm thinking switching to a wheel from a cb550 or the like)

I'll be watching to see how you get on with this.
I'd like to swap my 17" rear up to 18" and improve the rear brake performance at the same time.
 
Re: CB125s build. questions abound!

Are you going to swap just the wheel off a 550? Not sure it will fit plus what are you going to do about mounting the brake? I considered trying to swap on a whole 550 front end as i have all the parts but I think it will be just to heavy for a little bike. the other option is to go back to a drum up front. That is the easiest but it just isnt as racer looking as a disk.
 
Re: CB125s build. questions abound!

Popped the rear fender back on so I could ride it around while I wait for my taillight to come in (after I get my brake light on and seat shaved down and ready to go, I'm going to do the 12v conversion and rebuild my forks while I wait for my gazelles to come in)


I also put the speedo back on after this pic.


dsc0145w.jpg






ffjmoore said:
Are you going to swap just the wheel off a 550? Not sure it will fit plus what are you going to do about mounting the brake? I considered trying to swap on a whole 550 front end as i have all the parts but I think it will be just to heavy for a little bike. the other option is to go back to a drum up front. That is the easiest but it just isnt as racer looking as a disk.


I've got a ton of things to consider, and the guy at my local shop is an amazing source of information, as he builds pretty much exclusively old honda CB's.


If I can't get a good disc brake, I can always look at the smaller CB's for a big drum. a cb360's drum up front would look bad-ass.
 
Re: CB125s build. questions abound!

Erskine said:
I'll be watching to see how you get on with this.
I'd like to swap my 17" rear up to 18" and improve the rear brake performance at the same time.


You're going to run the risk of not being able to fit the rim in the space between the swing arm. As it is, any increase in tire size on the 17 means you will have to change out the rear brake linkage.


The back brake is actually pretty fantastic. You learn this by riding a bike that has a worthless front, haha


I see the gn250 has what I want. But what about the speedo? I want to run the standard speedo cable, as it matches the drive on my xs650 gauge.


Also, does anyone have any ideas for the headlight bulb? I need a 12v bulb, as once I get a taillight in, all my other lights will be ready for 12v.


I think I want to do this for my seat. Give it that mean cafe look while still letting me ride with a passenger (I get so many chicks that want to ride on this little thing!)


ys2b8633.jpg
 
Re: CB125s build. questions abound!

What about a cb360t wheel? looks like it has all the necessary parts, and I'd be willing to bet even money that the speedo drive cable is the same!


108313942_HONDA-CB360G.jpg
 
Re: CB125s build. questions abound!

FFJ, what do you use to polish the metal on your CB? I'm using 0000 steel wool, but it takes -forever-
 
Re: CB125s build. questions abound!

honeybadger said:
FFJ, what do you use to polish the metal on your CB? I'm using 0000 steel wool, but it takes -forever-
Which CB, i have too many? Ill assume your talking about the 125s. I use steel wool as well. It doesn't polish the metal as much as it scrapes off the rust spots. After that i use a chrome polish and a rag. Its not show quality, just not rusty.
 
Re: CB125s build. questions abound!


Had some good weather today, took it down to the park for some pics. Still lots of polishing to do, but it's coming along nicely. Can't wait for my new seat and taillight, so I can tear into them!


I can't believe after how rough it ran, that after one single gasket and a new float, it starts on the first kick every time now.

dsc0149sf.jpg



dsc0152z.jpg



dsc0153am.jpg



dsc0156d.jpg



My wire-wheeled point cover. Probably going to paint it black /w gold in the number wells.


dsc0158hs.jpg



fancy new shocks


dsc0163ld.jpg



I love the sticker on the tank


dsc0165jv.jpg
 
Back
Top Bottom