Texasstar said:crazypj was right honda likes a long smooth taper. We now have two steps. 1.12 to 1.25 and 1.25 to 1.4. I think there is a reason why some of the old megaphones were beyond the back wheel...when we brought the revs up I had to hold on to Lucky because the frequency and vibration started moving the bike all over on the blocks. Zeke and I were messing around playing the megaphones like trumpets and my oldest son accused us of being like six year old kids...gonna play them like trumpets again and see if we can "feel" the negative pressure wave when we add the cone.
You were right!!!! we are sometimes like doubting Thomas sticking his fingers in the socket in order to believe but this is where seeing, feeling, and hearing is more than believing it was like nothing we have heard before ... we got home and we pulled the cones off and played a note like a trumpet and added the reverse cone...you could feel the negative wave and hear the tonal change. We are NOT going to weld the reverse cones on at this time but want to weld some loops on the end of the megas for springs so we can make the cones removable and interchangeable. Also want to try different id diameter reverse cones on the dyno. We also like to turn our guitar amps up to 11crazypj said:Just got to say it TOLD YOU SO ;D
Really cool vid, you cant help trumpeting when you get new cones ;D
kopcicle said:I predict it will suck the oil right out of the crankcase ...
~kop
Yes they did. I have seen those pictures a dozen times and just noticed the hole in the starter block off plug and then I looked at the other pick and had an aha moment. Teazer how much difference does it make to make the swing arm 40mm longer? Is that why the gp200 bikes are running 13.2" shocks or to change the rake forward for more heat in the front tire?teazer said:Interesting pictures - did they come from Mike's website?
amazing what you find digging through blogs pair of cb77's one on left was a salt flat racer 17" front tires 19" rear the guy said it held a bonneville record for a few years...teazer said:We run stock length swingarms and slightly longer shocks on ours to raise the back end a little and make them turn a little faster. They are so light though that it doesn't make a lot of difference at the speeds we go.
For LSR, you probably want a bike that's stable and long wheelbase helps there.
Hopefully we made all the mistakes and as soon as we opened our throttle to WOT when we did our compression check our numbers went up substantiallymannydantyla said:Texasstar can I ask you some questions? I just rebuilt my motor (same as yours, well, if yours was stock) and it's running mostly pretty well right now, I've been breaking it in for the last few days.
The question for you is, how long did it take before your compression numbers where within spec? Following this breaking procedure, I'm about 5 runs into it and the last one I was using short bursts of WOT but keeping it below 80% of the redline RPM. But the last time I checked (right after the 4th run) my compression was 125-130 psi. I've read the first 40 or so pages of your thread and saw that you had this same experience.
Another concern of mine is that, when checking the compression, I peaked into the cylinder with a flashlight through the spark plug hole and saw what looks like a lot of oil sitting on the piston. That or it's gas, it's running very rich right now (gas can NOT be good for seating fresh rings). And there's a fair amount of smoke coming out the tail pipes. If I put my hand over the tips, it doesn't take long before my hand is splattered with black stuff (condensation + smoke, or something worse?)
Thank you!
BTW, I've learned so much by reading your threads and watching your videos.
You did fit the rings correctly?mannydantyla said:Texasstar can I ask you some questions? I just rebuilt my motor (same as yours, well, if yours was stock) and it's running mostly pretty well right now, I've been breaking it in for the last few days.
The question for you is, how long did it take before your compression numbers where within spec? Following this breaking procedure, I'm about 5 runs into it and the last one I was using short bursts of WOT but keeping it below 80% of the redline RPM. But the last time I checked (right after the 4th run) my compression was 125-130 psi. I've read the first 40 or so pages of your thread and saw that you had this same experience.
Another concern of mine is that, when checking the compression, I peaked into the cylinder with a flashlight through the spark plug hole and saw what looks like a lot of oil sitting on the piston. That or it's gas, it's running very rich right now (gas can NOT be good for seating fresh rings). And there's a fair amount of smoke coming out the tail pipes. If I put my hand over the tips, it doesn't take long before my hand is splattered with black stuff (condensation + smoke, or something worse?)
That's crazy. Two stroke reeds!Texasstar said:
this is a novel idea for crankcase venting![]()
Sent from my iPhone using Tapatalk