Father Son 75 CB200T Rise From the Ruins

Texasstar said:
crazypj was right honda likes a long smooth taper. We now have two steps. 1.12 to 1.25 and 1.25 to 1.4. I think there is a reason why some of the old megaphones were beyond the back wheel...when we brought the revs up I had to hold on to Lucky because the frequency and vibration started moving the bike all over on the blocks. Zeke and I were messing around playing the megaphones like trumpets and my oldest son accused us of being like six year old kids...gonna play them like trumpets again and see if we can "feel" the negative pressure wave when we add the cone.

Just got to say it TOLD YOU SO ;D
Really cool vid, you cant help trumpeting when you get new cones ;D
 
crazypj said:
Just got to say it TOLD YOU SO ;D
Really cool vid, you cant help trumpeting when you get new cones ;D
You were right!!!! we are sometimes like doubting Thomas sticking his fingers in the socket in order to believe but this is where seeing, feeling, and hearing is more than believing it was like nothing we have heard before ... we got home and we pulled the cones off and played a note like a trumpet and added the reverse cone...you could feel the negative wave and hear the tonal change. We are NOT going to weld the reverse cones on at this time but want to weld some loops on the end of the megas for springs so we can make the cones removable and interchangeable. Also want to try different id diameter reverse cones on the dyno. We also like to turn our guitar amps up to 11 ;) when mom is not around.


Sent from my iPad using Tapatalk
 
It has taken every ounce of restraint not to put the megacycle cam in Lucky but I think that this will prove productive in the learning department to keep this baseline of tuning so we can see the difference on the dyno with the exhaust changes. We know we are going to run out of air at 10.5k but if the polini velocity stacks made a .73 whp difference on the intake what do you predict the megaphones will do on the other end?


Sent from my iPad using Tapatalk
 
I would weld the reverse cones on eventually, may need to increase the outlet diameter though(not sure what you have at present?)
Probably needs around 2.00"~2.25"
You'll know if it worked, bike will lift front wheel when changing up at max rpm around 60mph ;)
 
kopcicle said:
I predict it will suck the oil right out of the crankcase ... :D

~kop
hebesu9a.jpg
nenubyga.jpg
this is a novel idea for crankcase venting


Sent from my iPhone using Tapatalk
 
teazer said:
Interesting pictures - did they come from Mike's website?
Yes they did. I have seen those pictures a dozen times and just noticed the hole in the starter block off plug and then I looked at the other pick and had an aha moment. Teazer how much difference does it make to make the swing arm 40mm longer? Is that why the gp200 bikes are running 13.2" shocks or to change the rake forward for more heat in the front tire?


Sent from my iPhone using Tapatalk
 
We run stock length swingarms and slightly longer shocks on ours to raise the back end a little and make them turn a little faster. They are so light though that it doesn't make a lot of difference at the speeds we go.

For LSR, you probably want a bike that's stable and long wheelbase helps there.
 
teazer said:
We run stock length swingarms and slightly longer shocks on ours to raise the back end a little and make them turn a little faster. They are so light though that it doesn't make a lot of difference at the speeds we go.

For LSR, you probably want a bike that's stable and long wheelbase helps there.
amazing what you find digging through blogs pair of cb77's one on left was a salt flat racer 17" front tires 19" rear the guy said it held a bonneville record for a few years...


Sent from my iPad using Tapatalk
ahu4yzer.jpg
 
have the cranks that you have pulled been true 360 degree cranks or was there a tolerance for when honda assembled them? Could one crank be off slightly? I am assuming the notches were used to line up the crank parts when they were pressed together? Our crank on the bench looks like one of the notches is off slightly. Or could pre-detonation cause this? When you put yours on a 180 did you weld the pressed pins to keep them from moving?

Assuming that the notches are used to set up the crank could we degree one of the crank pin using the notch to set it in relation to the other notches to get various rephases?


Sent from my iPad using Tapatalk
ade6u8yb.jpg
 
Texasstar can I ask you some questions? I just rebuilt my motor (same as yours, well, if yours was stock) and it's running mostly pretty well right now, I've been breaking it in for the last few days.

The question for you is, how long did it take before your compression numbers where within spec? Following this breaking procedure, I'm about 5 runs into it and the last one I was using short bursts of WOT but keeping it below 80% of the redline RPM. But the last time I checked (right after the 4th run) my compression was 125-130 psi. I've read the first 40 or so pages of your thread and saw that you had this same experience.

Another concern of mine is that, when checking the compression, I peaked into the cylinder with a flashlight through the spark plug hole and saw what looks like a lot of oil sitting on the piston. That or it's gas, it's running very rich right now (gas can NOT be good for seating fresh rings). And there's a fair amount of smoke coming out the tail pipes. If I put my hand over the tips, it doesn't take long before my hand is splattered with black stuff (condensation + smoke, or something worse?)

Thank you!

BTW, I've learned so much by reading your threads and watching your videos.
 
Hey Manny
Check your oil for gas ....
New rings are like worn out rings they don't fit the cylinders correctly untill you seat them
 
mannydantyla said:
Texasstar can I ask you some questions? I just rebuilt my motor (same as yours, well, if yours was stock) and it's running mostly pretty well right now, I've been breaking it in for the last few days.

The question for you is, how long did it take before your compression numbers where within spec? Following this breaking procedure, I'm about 5 runs into it and the last one I was using short bursts of WOT but keeping it below 80% of the redline RPM. But the last time I checked (right after the 4th run) my compression was 125-130 psi. I've read the first 40 or so pages of your thread and saw that you had this same experience.

Another concern of mine is that, when checking the compression, I peaked into the cylinder with a flashlight through the spark plug hole and saw what looks like a lot of oil sitting on the piston. That or it's gas, it's running very rich right now (gas can NOT be good for seating fresh rings). And there's a fair amount of smoke coming out the tail pipes. If I put my hand over the tips, it doesn't take long before my hand is splattered with black stuff (condensation + smoke, or something worse?)

Thank you!

BTW, I've learned so much by reading your threads and watching your videos.
Hopefully we made all the mistakes and as soon as we opened our throttle to WOT when we did our compression check our numbers went up substantially :) also make sure you have a good gauge. Harbor freight gauges are no bueno. We had white smoke until our rings were seated. The gas problem. Have you checked float levels and valve?


Sent from my iPhone using Tapatalk
 
mannydantyla said:
Texasstar can I ask you some questions? I just rebuilt my motor (same as yours, well, if yours was stock) and it's running mostly pretty well right now, I've been breaking it in for the last few days.

The question for you is, how long did it take before your compression numbers where within spec? Following this breaking procedure, I'm about 5 runs into it and the last one I was using short bursts of WOT but keeping it below 80% of the redline RPM. But the last time I checked (right after the 4th run) my compression was 125-130 psi. I've read the first 40 or so pages of your thread and saw that you had this same experience.

Another concern of mine is that, when checking the compression, I peaked into the cylinder with a flashlight through the spark plug hole and saw what looks like a lot of oil sitting on the piston. That or it's gas, it's running very rich right now (gas can NOT be good for seating fresh rings). And there's a fair amount of smoke coming out the tail pipes. If I put my hand over the tips, it doesn't take long before my hand is splattered with black stuff (condensation + smoke, or something worse?)
You did fit the rings correctly?
I've seen 'professional' mechanics get it wrong
Did you oil bores? It's a bad idea and causes rings to glaze over rather than seal
 
Thank you for your replies, I didn't mean to hijack your thread texasstar, LOL

I will check for gas in oil. That would be bad. The reason for the richness is the carbs just need to be re-adjusted after switching from emgo pods to uni filters with filter oil.
Yes I did oil the cylinders when installing the rings. I've read both opinions on this, but only after the fact.
Yes I made sure to install the rings correctly. In the correct order and with the indicator on the ring facing up.

Again, didn't mean to hijack your thread. I just needed to know when the compression numbers should improve, to indicate that the rings are sealed. Thank you guys!
 
Did you also use new o-rings for the oil passages when you re-assembled everything? Its possible that they could be bleeding between the head gasket if they aren't sealing well.

Part #38 on this diagram:
http://images.cmsnl.com/img/partslists/honda-cb200-general-export-cylinder-cylinder-head_bigma000150e01_0ab3.gif
 
The craziest part is the twincam head. Which for the life of me, I cant remember what he said its off of. When I talked to Mike on the phone a few years ago he was talking about all of his developments...

I think it might have started with an 80's GS250 head.

Except that one shown has more cooling fins... Hmm.
 
Back
Top Bottom