FZR600 fighter
- Thread starter JRK5892
- Start date
tWistedWheelz
BUILT NOT BOUGHT!
JRK5892 said:well... hit a road block... the gasket is on back order and is not expected to be in till the end of next week
BOOOO!
it is a rubber molded piece that has some cuts that fit into sections around the valve cover... no way to hack it, trust me i looked! no worries i will have to find some ohter crap to keep me busy, may just go ahead and install my LED kit. I have a road king coming in tonight that has to be out of the shop by Tues (for my uncle) so not only do i have to bust ass to get it done, but i have to cut him a killer price cause he is family!
well, got the bike off the table and cleaned house a bit... got the shop all organized and ready for a big weekend... i have to get 3 HD road kings with new bars, all new cables, pads, fluids, stereos wired, and chrome added to them done by Wed. big order to fill and stuff has to be clean as hell to stay organized and be able to rip though these.
I pulled the bike down and the new kick stand, PERFECT! for once my measurements where spot on, the weld angle is spot on for the foot, and man is this sucker low!!! i am not to crazy about the tail light and still may just tint or paint that and leave the ends open... but that is all to come. here are some pics, i know some of you where not feeling the headlight, but i have to say, i love it! LOVE IT!, the bike had 3 cars stop to check it out just sitting outside. i thought that was pretty cool!
keep in mind the wife is 5'2 and was in flip flops, this sucker is LOW
it is a bit dusty from blowing out the shop, but the guages look great! still need to powder the top resivor but the new brakes work AWESOME!!!!
not to sure about the back end
cleaned and ready for work!
wife had some time and so did I, so she wanted to take out the cafe, she hopped on the enfield, and i tossed an old set of clubmans on the KZ, and we went and found some good twisties to rip on for a few hours
I pulled the bike down and the new kick stand, PERFECT! for once my measurements where spot on, the weld angle is spot on for the foot, and man is this sucker low!!! i am not to crazy about the tail light and still may just tint or paint that and leave the ends open... but that is all to come. here are some pics, i know some of you where not feeling the headlight, but i have to say, i love it! LOVE IT!, the bike had 3 cars stop to check it out just sitting outside. i thought that was pretty cool!
keep in mind the wife is 5'2 and was in flip flops, this sucker is LOW
it is a bit dusty from blowing out the shop, but the guages look great! still need to powder the top resivor but the new brakes work AWESOME!!!!
not to sure about the back end
cleaned and ready for work!
wife had some time and so did I, so she wanted to take out the cafe, she hopped on the enfield, and i tossed an old set of clubmans on the KZ, and we went and found some good twisties to rip on for a few hours
Your build is freekin' awesome!!!! I like the tail light, myself.
For me, the headlight goes with the look of this bike, and looks good using a frame-mounted fairing stay.
But it's the orange powder coat that makes this thing a neck-breaker. That sh** is just the awesome sauce, matey!!!!
For me, the headlight goes with the look of this bike, and looks good using a frame-mounted fairing stay.
But it's the orange powder coat that makes this thing a neck-breaker. That sh** is just the awesome sauce, matey!!!!
on the frame i got some plastic plugs from ace, they fit right in and looked great!!!!
wife is a saint that is for sure, she is super pumped to take this sucker for a rip!
on the tail, i had to lower the bike so much so she could ride it there is really no way to raise the tail, i got 3 point adjust links in there so i can always just raise it up in like 2 min if i want to go up any more.
ok... so since i am still waiting on a gasket i figured i would get as much done as i can! so i did... only to find, i have a bit more work ahead of me. I got the lights hooked up all the wiring done... well kind of. the tail light worked great! i had to open up and re solder the front brake light switch, bt that sucker works now... I added in my turn sigs, using some of my 10mm hyper bright LED pods, with wired in resisters.. and here is where the problem comes in...
the prev owner must have fiddled with the wires, when you turn on the left turn, works great! but the right, all 4 turn sigs flash... no big deal just got to get a wire diagram from somewhere and fix it.
everything else works great! when i click the run button i can hear the fuel pump prime, driving and brights... the whole shabang!
got the header on (new exhaust gaskets), as well as the muffler on the bike, fresh oil change, mirrors on, grips on, stator put together and on, fuel tank in, and some other odds and ends!
here are some pictures!
tail light (turn sigs on the the lower section of the liscnse plate bracket... yes they are small but MAN are they bright!!!
tail light on (before i installed the turn sigs)
headlight
stator cover and header
pipe
grip and mirror
wife is a saint that is for sure, she is super pumped to take this sucker for a rip!
on the tail, i had to lower the bike so much so she could ride it there is really no way to raise the tail, i got 3 point adjust links in there so i can always just raise it up in like 2 min if i want to go up any more.
ok... so since i am still waiting on a gasket i figured i would get as much done as i can! so i did... only to find, i have a bit more work ahead of me. I got the lights hooked up all the wiring done... well kind of. the tail light worked great! i had to open up and re solder the front brake light switch, bt that sucker works now... I added in my turn sigs, using some of my 10mm hyper bright LED pods, with wired in resisters.. and here is where the problem comes in...
the prev owner must have fiddled with the wires, when you turn on the left turn, works great! but the right, all 4 turn sigs flash... no big deal just got to get a wire diagram from somewhere and fix it.
everything else works great! when i click the run button i can hear the fuel pump prime, driving and brights... the whole shabang!
got the header on (new exhaust gaskets), as well as the muffler on the bike, fresh oil change, mirrors on, grips on, stator put together and on, fuel tank in, and some other odds and ends!
here are some pictures!
tail light (turn sigs on the the lower section of the liscnse plate bracket... yes they are small but MAN are they bright!!!
tail light on (before i installed the turn sigs)
headlight
stator cover and header
pipe
grip and mirror
tWistedWheelz
BUILT NOT BOUGHT!
Looking great Joe! Almost there brother! It is another killer scoot! Just one more bad ass bike to add to the list that has rolled out of lite'em up! Keep'em comin!
dakine_surf
"Stay Thirsty my Friends"
I'll give you a hell ya!
http://www.youtube.com/v/7LuSP4QaXiQ&hl=en_US&fs=1&color1=0x234900&color2=0x4e9e00&border=1
http://www.youtube.com/v/7LuSP4QaXiQ&hl=en_US&fs=1&color1=0x234900&color2=0x4e9e00&border=1