KZ550- Iron Geek K Zeta

PeteyWash said:
So,

From here we need to get the front brake properly mounted. Definitely need to get into the carbs and check out the valves, because this bike does not run well. After that the list is as follows:

paint tail
upholster seat
tail light
sand, polish, and clear the tank
rear sets?
properly mount ignition
............... you never really do finish do you

When you do the valves, check the clearances and write them all down. These use the under-the-bucket shims. That way, if you know you are too tight, you can go one size thinner on the next one. But you'll only be able to know that by taking measurements and writing them down first. Also, if you don't have one yet, get a micrometer. Many of the shims have lost the marking telling you what size they are. Just a heads up! She's looking better and better sir! 8)
 
Thanks man. The bike needs it. It's not running well. BTW what did you do to bump up your jet sizes? Did you buy a kit or do the drill procedure?
 
PeteyWash said:
Thanks man. The bike needs it. It's not running well. BTW what did you do to bump up your jet sizes? Did you buy a kit or do the drill procedure?


Tiny f'ing drill bits my friend. I'm going to be firing that bike up shortly to see how rich or lean I am. I think I drilled the pilots to the #78 bit. I'm running round jets from mikunis or keihins at #117 right now. I may go back and drill out the originals larger as I realize that non-TK jets aren't the same sizing (hence the 117) I also bought a bunch of really really tiny washer that slipped under the slide needle, to raise it up and Richen the circuit, as well as keep the slides lower to keep the idle from racing away. I'll let you know what I come up with, as the colortune I just bought should tell me if I'm rich or lean at idle at least. Then the O2 sensor setup I got should tell me what's going on at mid and top of the range.
 
MotorbikeBruno said:
Tiny f'ing drill bits my friend. I'm going to be firing that bike up shortly to see how rich or lean I am. I think I drilled the pilots to the #78 bit. I'm running round jets from mikunis or keihins at #117 right now. I may go back and drill out the originals larger as I realize that non-TK jets aren't the same sizing (hence the 117) I also bought a bunch of really really tiny washer that slipped under the slide needle, to raise it up and Richen the circuit, as well as keep the slides lower to keep the idle from racing away. I'll let you know what I come up with, as the colortune I just bought should tell me if I'm rich or lean at idle at least. Then the O2 sensor setup I got should tell me what's going on at mid and top of the range.

Thanks so much man. Keep me posted
 
MotorbikeBruno said:
Tiny f'ing drill bits my friend. I'm going to be firing that bike up shortly to see how rich or lean I am. I think I drilled the pilots to the #78 bit. I'm running round jets from mikunis or keihins at #117 right now. I may go back and drill out the originals larger as I realize that non-TK jets aren't the same sizing (hence the 117) I also bought a bunch of really really tiny washer that slipped under the slide needle, to raise it up and Richen the circuit, as well as keep the slides lower to keep the idle from racing away. I'll let you know what I come up with, as the colortune I just bought should tell me if I'm rich or lean at idle at least. Then the O2 sensor setup I got should tell me what's going on at mid and top of the range.

That is crazy. I want to put K&N's and a 4 into 1 pipe on my KZ550, but Im not sure it will be worth all the effort.


Tim
 
County Fair said:
That is crazy. I want to put K&N's and a 4 into 1 pipe on my KZ550, but Im not sure it will be worth all the effort.


Tim

I already bought the drills and drilled my main jets.... with some luck it should all work out. check this link out: http://www.kzrider.com/forum/3-carburetor/306842-kz550-main-jet-size-advice-needed
 
PeteyWash said:
I already bought the drills and drilled my main jets.... with some luck it should all work out. check this link out: http://www.kzrider.com/forum/3-carburetor/306842-kz550-main-jet-size-advice-needed

I used a ton of info from this page...

http://home.comcast.net/~loudgpz/GPZweb/TK22mainPage/TK22mainPage.html

The news so far: I think I'm STILL lean, at #78 drill bit on the pilots. I'm going to go ONE step further as I do have #77 bit on hand. I'm almost seated on all of the mixture screws at idle. I'll report back after drilling again. After I deal with the lean condition at idle, I'll get the O2 program fired up and test it with the wideband kit. Hopefully that will give me an idea of how the Keihin jet is doing for the top end.
 
Thanks man. You have been a world of help.....

County Fair said:
Great link. This is going to be a ton of help.

Thanks,

Tim

I have looked at this website a good bit. Very helpful.
I got two questions for you, since I already drilled my mains out to like 105 or 107 I think (b/c I got stacks and not muffler):

Do you still have the stock headers on your bike (it seems so)? The ones with actual baffle in them already
And how did those other jets work for you? because I may just go ahead and order some to be safe.
 
PeteyWash said:
Thanks man. You have been a world of help.....

I have looked at this website a good bit. Very helpful.
I got two questions for you, since I already drilled my mains out to like 105 or 107 I think (b/c I got stacks and not muffler):

Do you still have the stock headers on your bike (it seems so)? The ones with actual baffle in them already
And how did those other jets work for you? because I may just go ahead and order some to be safe.


Still the stock headers, however I chopped them just after the bend (going under the frame) and did individual exhausts with wider inner diameters, then baffled them. (yeah I know 4-1 would pull the exhaust gases better but I wanted the look)

As for the other jets...I won't really know until I get to tuning that part. The keihins have the throat in a different spot. I was thinking of grinding down the head, but it's slotted vs. the TK head which is hexagonal. I had some time this morning at break and drilled out the pilots to #77 bit, which is like a 44 pilot jet size. It was 39 and I was running far too lean still. I'll let you know what's up with that.
 
Ok, cool. Yeah me and my buddy were planning on running a 4 into 2, but we still will use the stock headers and open pipes after. SO this is good! You struggle through everything and we just feed off of your information..... haha.

Thanks again,
Peter
 
PeteyWash said:
Ok, cool. Yeah me and my buddy were planning on running a 4 into 2, but we still will use the stock headers and open pipes after. SO this is good! You struggle through everything and we just feed off of your information..... haha.

Thanks again,
Peter

Haha, story of my life! Just kidding ;) I have always had a love/hate relationship with my KZ, I figured it was time to make it a love/love one before she goes to her new owner ;D
 
MotorbikeBruno said:
Haha, story of my life! Just kidding ;) I have always had a love/hate relationship with my KZ, I figured it was time to make it a love/love one before she goes to her new owner ;D

Haha. Yeah, btw how did she ride? From what I've read when the 550 came off the production line it could do 120. Ofcourse the stock speedo doesn't read that far up...... which is dumb
 
Either of you guys simplify the wiring? I'm trying to figure out the bundle of crap I got going and want to reduce it but man! It's almost overwhelming!!
Glad you two have ventured out first so I can follow the builds....
 
goochwarmer said:
Either of you guys simplify the wiring? I'm trying to figure out the bundle of crap I got going and want to reduce it but man! It's almost overwhelming!!
Glad you two have ventured out first so I can follow the builds....

Yeah I went through the wiring harness on this bike... If you have a wiring diagram and some time then you should be ok. That was my first time that I really messed with wiring and it came out fine. Definitely go back and switch your fuses to modern ones........ The guy who I'm helping build this bike told me to take my time, b/c it's easy to get ahead of yourself with wiring...... he was right. Just cut open the huge mass and go from there. I think I did away with 40-45% of the wires that were previously in there.
 
Yeah, I think I lost at least 50% or more. Just remember that everything needs power, and GOOD grounds and you'll be fine.

As for the ride. It didn't happen as I'm in Minnesota...we have had crappy weather this week, and a "possible" 6"-10" of snow again...ugh. But it DID fire up nicely and run on all 4 now...instead of an intermittent 2/3 thing going on haha.
 
Well it appears I can cut a lot of the wiring but am confused about two things maybe you guys can help with:
1. WTF is the white with blue stripe wire? It goes to NOTHING!! Traveler wire for testing? And why isn't it on the legend?
2. I think I read the brown as a the common for all lighting and Black yellow as ground....aren't they the same thing if I ground them togeather? Or is brown considered the neutral? Or am I overthinking this?

I plan on upgrading to new fuses and have a new bunch of wire but for now may just move the ignition to a differant place and wait until next winter.

SPeaking of winter in spring Bruno we just got 14" in two days up here. Snow was just starting to melt and I saw a few bikes out already and started getting nervous I wasn't ready for hte season. But after a larger push to get the bike ready I realize I am not ready at all. Crap.
 

Attachments

goochwarmer said:
Well it appears I can cut a lot of the wiring but am confused about two things maybe you guys can help with:
1. WTF is the white with blue stripe wire? It goes to NOTHING!! Traveler wire for testing? And why isn't it on the legend?
2. I think I read the brown as a the common for all lighting and Black yellow as ground....aren't they the same thing if I ground them togeather? Or is brown considered the neutral? Or am I overthinking this?

I plan on upgrading to new fuses and have a new bunch of wire but for now may just move the ignition to a differant place and wait until next winter.

SPeaking of winter in spring Bruno we just got 14" in two days up here. Snow was just starting to melt and I saw a few bikes out already and started getting nervous I wasn't ready for hte season. But after a larger push to get the bike ready I realize I am not ready at all. Crap.

Yeah, that white with blue is on the legend as (Blue WITH white) it was incorrect. It has the 10 amp fuse to nowhere, as it was part of the accessory wiring if you wanted to throw another 12V something on there.
 
Yes I figured the legend was wrong (after much consideration) and was going to remove it from the harness. THanks again and sorry to bugger up your thread.
 
Re: KZ550- Iron Geek K Zeta- *This Article Should Make Your Day*

This should make anyone's day who is struggling through a kz550 project:

http://www.maclean-nj.com/kwak55.htm
 
Back
Top Bottom