"Patina" The 1973 CB175 Cafe Racer

Well we have an engine problem.

I finally got the kickstart lever to depress however it's only engaging the clutch shaft, not the crank. The top end is entirely free and the pistons rise and fall and the valves opening close like they're supposed to.

When I try to kick the bike over in neutral it only spins the clutch shaft but doesn't engage the crankshaft internally somehow. We took the right side engine components off all the way down to the case. Everything spins freely on the countershaft but for some reason it's just not turning over the crankshaft.

When you put the bike in gear and try to bump it off the transmission engages the back wheel through the chain so everything is fine there. We're also getting a spark through the electronic ignition so it's safe to say I could technically bump the bike off to start it but I don't want to add oil knowing that I want to get the kick start working right and have to drain it back out again.

What is messed up that's preventing the crankshaft from being engaged by the countershaft? Is countershaft even the right word there? I mean the shaft that runs through the clutch basket.

Help?




Sent from my iPhone using Tapatalk
 
Take the right side engine cover off again. The clutch basket has a gear that should mate directly with the gears on the crankshaft.
 
Yup sure does. It's like the kickstarter is slipping internally somewhere.

dytujuty.jpg



Sent from my iPhone using Tapatalk
 
So here's what we know: the kick start is engaging the SHAFT that the clutch basket is sitting on. When the lever is depressed, the splined clutch shaft spins. When the clutch basket is installed, the gears around the clutch basket do not turn to engage the small gears on the crank.

It's almost like There's not enough tension on the clutch pressure plate to make it so that the outer clutch basket will engage with the shaft. Is that possible?

Is it possible that I have weak springs?



Sent from my iPhone using Tapatalk
 
The knot thing about that is that the clutch works fine. And the bike was riding before I tore it down...so springs likely not the issue?


Sent from my iPhone using Tapatalk
 
So... to kick the engine over, the bike needs to be in neutral and the clutch lever cannot be engaged. You need to have the clutch plates installed (along with the springs) for it to work.
 
Sonreir said:
So... to kick the engine over, the bike needs to be in neutral and the clutch lever cannot be engaged. You need to have the clutch plates installed (along with the springs) for it to work.

Agreed. I was just saying that before the engine was torn apart I didn't have this issue and everything was fine - this was my way to rule out that it was not bad parts but rather an assembly issue :)

Right now, with the clutch lever released and the bike in neutral, the kickstarter spins the clutch shaft within the clutch basket (coming through the case) but the basket gears and basket does not spin). Leads me to believe that it's an engagement issue or something with the clutch...?


Sent from my iPhone using Tapatalk
 
WOOP!!! Figured it out. Turns out that the clutch engagement on the left side of the bike was slightly out of adjustment. The adjustment was a little bit too much, such that the clutch was disengaged with the pressure plates slipping. That allowed for the basket to not be able to turn.

Everything's engaging now :D


Sent from my iPhone using Tapatalk
 
Well, unlucky nasty rainy day today. Had everything ready to go, fueled up, oiled up and ignition making a spark.

Went to kick over the EXTREMELY tight new rebuilt engine and sheared the kickstart shaft off at the side case.

I had to walk away....

That being said (and I know this is a subjective question), how "tight" should a rebuilt engine be? I mean I know there's a lot of unmated surfaces and no oil up top yet, but to get the kickstart to move I had to put more than just my body weight on it. Do things significantly loosen up after things heat up and mate and get lubricated around seals and whatnot?

Another thing, because of this is it better to bump a new engine off?


Sent from my iPhone using Tapatalk
 
Things shouldn't be any stiffer than normal. In fact, an engine should get "tighter" as it breaks in.
 
Sonreir said:
Things shouldn't be any stiffer than normal. In fact, an engine should get "tighter" as it breaks in.

Ok, due to heat and mating?


Sent from my iPhone using Tapatalk
 
When an engine is first rebuilt, there are microscopic gaps between many of the mating surfaces, primarily the piston rings and cylinders, and the rocker arms and the cam. As the engine runs, the high points (causing the gaps) wear down and more contact is made. This isn't usually a bad thing.

What engine work have you had done on this bike since you've had it?
 
Sonreir said:
When an engine is first rebuilt, there are microscopic gaps between many of the mating surfaces, primarily the piston rings and cylinders, and the rocker arms and the cam. As the engine runs, the high points (causing the gaps) wear down and more contact is made. This isn't usually a bad thing.

What engine work have you had done on this bike since you've had it?

Entire engine was apart. Bottom and top end. Jugs bored 1.00 over, 1.00 pistons and rings installed. New seals and gaskets. Other than that everything was just inspected and reassembled.


Sent from my iPhone using Tapatalk
 
Sonreir said:
Did he have the pistons with him when he bored the cylinders?

Yessir, the machinist used them to properly bore the jugs. That was a little factoid I made sure happened.

I mean, don't get me wrong, I can turn the engine over by hand at the alternator. It just takes probably 35 or more ft-lb I would guess. I didn't measure it.


Sent from my iPhone using Tapatalk
 
After my rebuild on my 360, my 5 year old could turn the engine over with a 14mm wrench. I'm guessing something might be wrong with yours. :(
 
Sonreir said:
After my rebuild on my 360, my 5 year old could turn the engine over with a 14mm wrench. I'm guessing something might be wrong with yours. :(

Crap.


Sent from my iPhone using Tapatalk
 
Initially when we rebuilt ours it turned over easy. But when we changed to single valve springs we put it in coil bind. It started and loped like a Harley and also spewed oil like one for a few seconds and then we disassembled and found the problem and switched to our other valve springs.

Anything shiny in the oil?


Sent from my iPhone using Tapatalk
 
Also the first time you fire up make sure you are getting oil to the top the engine


Sent from my iPhone using Tapatalk
 
Back
Top Bottom