"Patina" The 1973 CB175 Cafe Racer

Re: "Patina" The 1973 CB175 Cafe Racer

It's like as soon as I stick the probes in the caps it reads a resistance for a split second between 15-19 and then it zeros out.
 
Re: "Patina" The 1973 CB175 Cafe Racer


cafe mike said:
So you tried to get spark? Or or you just measuring stuff

I did try to get a spark. No luck. I'd rather get a spark than measure stuff any day :D
 
Re: "Patina" The 1973 CB175 Cafe Racer


cafe mike said:
Pull the coil wires out and measure just the wires

I did. Take a look at my first post. I have equal resistance across the wires as I do across the coils..
 
Re: "Patina" The 1973 CB175 Cafe Racer

I'm going to run to the store and get some dielectric grease to spear on the self tapping screw head. Maybe that'll do something. That conductor through the 7 mm wire is so small. I know I'm hitting the conductor with the screw because you can feel the copper crunch as opposed to the soft insulation when you hit it.
 
Re: "Patina" The 1973 CB175 Cafe Racer

Again I have continuity through the wires to the ends, and continuity through the actual cap alone...just nothing when I put the cap on the wire. Any ideas guys?
 
I'm getting a reading of 4.41 ohms measuring the wire with cap on.
 

Attachments

  • image.jpg
    image.jpg
    304.3 KB · Views: 298
Re: "Patina" The 1973 CB175 Cafe Racer


Well I think that's the problem. Yes, I have 5 k-ohm across each cap individually and a little less than 17 k- ohm across the coil and across the wires through the coil. When I screw on the caps I get squat.

I figured it was a bad connection through the screw but then again I've tried to screw the caps on about 80 times haha
 
Cut off the damaged part of wire and try again, don't go bat shit crazy tighten the down and make a mark on wire so you know when your down in cap
 
Re: "Patina" The 1973 CB175 Cafe Racer


cafe mike said:
Cut off the damaged part of wire and try again, don't go bat shit crazy tighten the down and make a mark on wire so you know when your down in cap

So I can't just thread a little on to test? I have to bottom out the wire in the cap?
 
Re: "Patina" The 1973 CB175 Cafe Racer

Ok so I measured from the coil end of the wire, through the wire, through the cap and got about 5 k-ohm through each. I know the cap is screwed in right now.

When I plug the connectors into the coil, I get zero when measured through the caps. If I remove the plugs and read through the coil I get 17 or so.
 
Re: "Patina" The 1973 CB175 Cafe Racer

1sttimer said:
Ok so I measured from the coil end of the wire, through the wire, through the cap and got about 5 k-ohm through each. I know the cap is screwed in right now.

When I plug the connectors into the coil, I get zero when measured through the caps. If I remove the plugs and read through the coil I get 17 or so.
Still no spark. Have you ever had the ei to spark for you? And your old coil was bad when you checked it?
 
Re: "Patina" The 1973 CB175 Cafe Racer

Yup, I had the EI spark for me once with the old coil. Old coil went out so I bought the new one. The signal lights on the EI show that it's functioning properly.

I just can't get continuity through the loop between the coil, out one wire through one cap, across the multimeter, through the second cap and second wire and back through the coil.
 
Re: "Patina" The 1973 CB175 Cafe Racer

1sttimer said:
Ok so I measured from the coil end of the wire, through the wire, through the cap and got about 5 k-ohm through each. I know the cap is screwed in right now.

When I plug the connectors into the coil, I get zero when measured through the caps. If I remove the plugs and read through the coil I get 17 or so.
Are you measuring the coil with power leads disconnected?
 
Re: "Patina" The 1973 CB175 Cafe Racer


cafe mike said:
Are you measuring the coil with power leads disconnected?

No...I guess I should do that. Good point. That still doesn't explain the lack of spark though right?
 
Re: "Patina" The 1973 CB175 Cafe Racer

1sttimer said:
No...I guess I should do that. Good point. That still doesn't explain the lack of spark though right?

I tried to call ya.
 
Re: "Patina" The 1973 CB175 Cafe Racer

1sttimer said:
No...I guess I should do that. Good point. That still doesn't explain the lack of spark though right?
I get 25.01 k ohm when I insert meter leads into caps with power wires still connected
 
Re: "Patina" The 1973 CB175 Cafe Racer


cafe mike said:
I get 25.01 k ohm when I insert meter leads into caps with power wires still connected

Not through the resistor caps and wire but into the coil?
 
Re: "Patina" The 1973 CB175 Cafe Racer

cafe mike said:
Are you measuring the coil with power leads disconnected?
Make sure you run the wire into the coil all the way before slipping your boot around coil insulated post, I think your not going in far enough to make continuity
 
Back
Top Bottom