"Patina" The 1973 CB175 Cafe Racer

Re: "Patina" The 1973 CB175 Cafe Racer


cafe mike said:
I tried to call ya.

Sorry man I had to step away for a sec. I only have my work phone but ill call you back here shortly if
You're available
 
Re: "Patina" The 1973 CB175 Cafe Racer

1sttimer said:
Sorry man I had to step away for a sec. I only have my work phone but ill call you back here shortly if
You're available
 

Attachments

  • image.jpg
    image.jpg
    278.9 KB · Views: 300
Re: "Patina" The 1973 CB175 Cafe Racer


cafe mike said:
Make sure you run the wire into the coil all the way before slipping your boot around coil insulated post, I think your not going in far enough to make continuity

Ohhh ok now that's something I haven't tried. I'll give that a shit here in a bit.
 
Re: "Patina" The 1973 CB175 Cafe Racer

1sttimer said:
Not through the resistor caps and wire but into the coil?
That's sticking the test leads into both resistor caps. And wires plugged into coil
 
Re: "Patina" The 1973 CB175 Cafe Racer

1sttimer said:
Ohhh ok now that's something I haven't tried. I'll give that a shit here in a bit.
We'll hurry the f up.. I need running sounds on your end...
 
cafe mike said:
Looks like you posted something. But nothing is showing

Apparently I havent figured how to post YouTube videos. It was Toby Keith's little less talk and a lot more action.
 
The best I can do. Make sure that your crimp is round so that it fits into coil. Measure depth of coil. And make sure your wire is going all the way down
 

Attachments

  • image.jpg
    image.jpg
    215.8 KB · Views: 272
Re: "Patina" The 1973 CB175 Cafe Racer


cafe mike said:
The best I can do. Make sure that your crimp is round so that it fits into coil. Measure depth of coil. And make sure your wire is going all the way down

Thanks sir. I got 19 mm depth and I'm going 19 mm in. Still no continuity. I'm baffled.
 
Re: "Patina" The 1973 CB175 Cafe Racer


xb33bsa said:
did you strip the lead and fold it back ?

Yessir. I am getting a really solid connection that takes some effort to get in and out of the coil, really snug. I even tried to take the connectors off and shove the bare wire in there to get continuity. Nothing...
 
Re: "Patina" The 1973 CB175 Cafe Racer

I have about .5" of bare wire that's in contact with the connector metal.
 
I'm baffled too. Your getting good continuity when you test wires with boots on (and ohms)
Your coil tests good. And when you plug in wires your getting nothing. Even when you change your meter selection? I have auto range.
 
Re: "Patina" The 1973 CB175 Cafe Racer

Is it a copper core wire?


Sent from my iPhone using Tapatalk
 
Re: "Patina" The 1973 CB175 Cafe Racer

The interesting thing is that as soon as I touch the leads to connect the circuit, I instantaneously read a resistance on the order of what I would expect. Then it zeros out. If I remove one test lead and reconnect, I read a resistance again for a second then it goes away.
 
Re: "Patina" The 1973 CB175 Cafe Racer

What readings are you getting on your coil


Sent from my iPhone using Tapatalk
 
Re: "Patina" The 1973 CB175 Cafe Racer

Across the terminals I'm getting about 16.75 k-ohms. Across the wires individually I'm getting about 4.7 each. If resistances add then I'm getting about what Mike was getting across the resistance caps (about 25 k-ohms).
 
Back
Top Bottom