"Patina" The 1973 CB175 Cafe Racer

Re: "Patina" The 1973 CB175 Cafe Racer

Take you voltage ohmmeter and stick the positive in the copper core on one side in the negative and see what kind of continuity you have Without the ends


Sent from my iPhone using Tapatalk
 
Re: "Patina" The 1973 CB175 Cafe Racer


Texasstar said:
Take you voltage ohmmeter and stick the positive in the copper core on one side in the negative and see what kind of continuity you have Without the ends


Sent from my iPhone using Tapatalk

Yeah see this is where it gets weird. Without the resistor caps, if I just stick the positive test lead in one wire copper open end and the negative in the other, I get equal resistance that there is through the coil without the wires - about 16.59 k-ohms...

But if I read the voltage through the wire alone with the caps on, I get about 5 k-ohms each. And if I read through the cap alone, I get what it's rated for, about 5.

It's the weirdest thing. The test you asked me to perform shows that the connection to the coil is good, because my resistances match.

But if I test the caps alone they are also good. The combination is not.
 
Re: "Patina" The 1973 CB175 Cafe Racer

What you said before you were not getting any continuity with the Caps on is that Correct


Sent from my iPhone using Tapatalk
 
Re: "Patina" The 1973 CB175 Cafe Racer

Do you have your old plug wires and caps


Sent from my iPhone using Tapatalk
 
Re: "Patina" The 1973 CB175 Cafe Racer


Texasstar said:
What you said before you were not getting any continuity with the Caps on is that Correct


Sent from my iPhone using Tapatalk

I'm not getting continuity with the spark plug wires plugged into the coil with the resistance caps on, taking the measurement through the caps.
 
Re: "Patina" The 1973 CB175 Cafe Racer


Texasstar said:
Do you have your old plug wires and caps


Sent from my iPhone using Tapatalk

Yeah I do. But they are the epoxy kind I think .
 
Re: "Patina" The 1973 CB175 Cafe Racer

Are you testing the continuity by putting one lead into one plug cap and the other lead into the other plug cap


Sent from my iPhone using Tapatalk
 
Re: "Patina" The 1973 CB175 Cafe Racer

With both wires connected to the coil


Sent from my iPhone using Tapatalk
 
Re: "Patina" The 1973 CB175 Cafe Racer


Texasstar said:
Are you testing the continuity by putting one lead into one plug cap and the other lead into the other plug cap


Sent from my iPhone using Tapatalk

Yessir... That's what I thought I saw Zeke doing in your vid :)
 
Re: "Patina" The 1973 CB175 Cafe Racer


Texasstar said:
With both wires connected to the coil


Sent from my iPhone using Tapatalk

Well I did it both ways. I also took one plug out of the coil and tried to make a loop by one test lead in the open coil port and the tort lead in the plug cap. No resistance. Tried it with both wires.
 
Re: "Patina" The 1973 CB175 Cafe Racer

Okay strip back 1 inch so that your copper is exposed folded over shove it in to the coil and check it without the caps


Sent from my iPhone using Tapatalk
 
Re: "Patina" The 1973 CB175 Cafe Racer

Also our caps line up with the and of the silicone wire going into the coil


Sent from my iPhone using Tapatalk
 
Re: "Patina" The 1973 CB175 Cafe Racer


Texasstar said:
Okay strip back 1 inch so that your copper is exposed folded over shove it in to the coil and check it without the caps


Sent from my iPhone using Tapatalk

Well I've already tried it with the metal connectors on and no resistor caps and got 16.6 k-ohms. So my connections up there are good right?
 
Re: "Patina" The 1973 CB175 Cafe Racer


Texasstar said:
Also our caps line up with the and of the silicone wire going into the coil


Sent from my iPhone using Tapatalk

Sorry, what do you mean here?
 
Re: "Patina" The 1973 CB175 Cafe Racer

No leave the resistor caps screwed in the wire removed the metal ends that go into the coil The exposed end of the copper into the coil


Sent from my iPhone using Tapatalk
 
Re: "Patina" The 1973 CB175 Cafe Racer


Texasstar said:
No leave the resistor caps screwed in the wire removed the metal ends that go into the coil The exposed end of the copper into the coil


Sent from my iPhone using Tapatalk

Oh yeah tried that. Jammed the bare wire into the coil, got nothing.
 
Re: "Patina" The 1973 CB175 Cafe Racer

Ok with the resistor Screwed in and the exposed copper on the other end test the continuity


Sent from my iPhone using Tapatalk
 
Re: "Patina" The 1973 CB175 Cafe Racer


Texasstar said:
Ok with the resistor Screwed in and the exposed copper on the other end test the continuity


Sent from my iPhone using Tapatalk

Just continuity across the wire and resistor? or with both wires bare on one end and jammed in the coil?
 
Re: "Patina" The 1973 CB175 Cafe Racer

Sorry I am yeah just with the cap and the end of the wire no coil


Sent from my iPhone using Tapatalk
 
Back
Top Bottom