"Patina" The 1973 CB175 Cafe Racer

Re: "Patina" The 1973 CB175 Cafe Racer


xb33bsa said:
it looks like you are doing great
i still think it is a good idear to check the timing in a dynamic mode(engine running and reved past 3000)with a strobe

Oh certainly. I'll do that tomorrow. We posted at thee same time.
 
Re: "Patina" The 1973 CB175 Cafe Racer

So since it's a bump start, I have to keep the stator cover on, fire it up, and then take the cover off.

A couple questions that I want to address that have been lightly answered already.

1) opening the cover released about 1/3 quart of oil. Running this low won't be a problem?

2) how much oil should I expect to splash out when I open the cover? I opened a tappet cover once while it was running and got a handful of hot oil...just wanna know what to expect...
 
a few ounces no problems np worries
fiil back up when done
you could also make a clear cover or a light sheatmetal cover with a large window cutout, some duct tape to seal around bottom
 
Re: "Patina" The 1973 CB175 Cafe Racer


xb33bsa said:
a few ounces no problems np worries
fiil back up when done
you could also make a clear cover or a light sheatmetal cover with a large window cutout, some duct tape to seal around bottom

That's a clever idea. Thanks for the info there.
 
xb33bsa said:
you could also make a clear cover or a light sheatmetal cover with a large window cutout, some duct tape to seal around bottom

Get a spare cover and cut a small hole at the timing pointer. XB is correct in principal, but you might be surprised at how much oil gets thrown around without a cover and even with a cover with inspection hole, expect some splashing.

I suppose you could get all sophisticated and make a clear acrylic cover or get an inspection window and insert that into the cover.
 
Re: "Patina" The 1973 CB175 Cafe Racer


teazer said:
Get a spare cover and cut a small hole at the timing pointer. XB is correct in principal, but you might be surprised at how much oil gets thrown around without a cover and even with a cover with inspection hole, expect some splashing.

I suppose you could get all sophisticated and make a clear acrylic cover or get an inspection window and insert that into the cover.

Thanks Teazer. I believe an acrylic shield would be good but it would have to be domed to clear the nut I believe. Getting a spare cover would work for sure. The only part I would have to cut out to see is the static reference point on the stator correct?

Pardon the ignorance. I believe I'm just looking for a clear "frozen" F right at the pointer?
 
Re: "Patina" The 1973 CB175 Cafe Racer

I was also thinking of starting it with a 14mm socket on my electric drill...but I'm not sure what's going to happen when the RPMs catch up with the drill...broken arm?
 
if you get it warmed up then remove cover,while running
(have screws already just snug) while leaning the bike to the opposite it should minimize spillage
 
1sttimer said:
Thanks Teazer. I believe an acrylic shield would be good but it would have to be domed to clear the nut I believe. Getting a spare cover would work for sure. The only part I would have to cut out to see is the static reference point on the stator correct?

Pardon the ignorance. I believe I'm just looking for a clear "frozen" F right at the pointer?

Yes and no.

In theory, YES you would align the F mark at idle, but to be honest, that's only a place to start. What we need is the fully advanced timing to be right and that's between those pair of marks. You can start with it at one mark or the other or in between and see how it runs and if it needs less or more advance, you can adjust it as required.

But as a place to start, we want the fully advanced timing to be correct and the timing at idle is fine as long as it's close to the F mark.

Another approach is to set full Advance timing in the mid spot and then check idle timing. If it's advanced , retard the timing until the full advance is closer to the later mark. Timing can be tweaked but the over riding event is full advance timing because that's weher teh bike runs at ant revs over about 3000RPM and that's most riding conditions
 
Re: "Patina" The 1973 CB175 Cafe Racer


teazer said:
Another approach is to set full Advance timing in the mid spot and then check idle timing. If it's advanced , retard the timing until the full advance is closer to the later mark. Timing can be tweaked but the over riding event is full advance timing because that's weher teh bike runs at ant revs over about 3000RPM and that's most riding conditions

I'm a little confused to the whole process in general (as far as what I'm looking for on the crank when I point the timing light at the static pointer).

I think I am trying to understand the correlation between the two full advance marks and the "F" mark on the crank. From what I know, I'm going to be shining the light on the crank at the static pointer looking for a clear "F" resting frozen right at that pointer line? As I need to do this at 3k-4k RPMs to ensure that I'm not getting retarded timing as the RPMs increase. If I am, I need to advance it slightly so it's timed correctly at higher (more commonly used) RPMs?

Is it safe to say that you are always going to be more advanced at 1500 RPMs than you are at say 5k? Another way to ask this is do race bikes set their engines much further in advance than street bikes, knowing they need the ignition to fire correctly at 7-11k or race RPMs?
 
the f mark is for at idle speed and or static
the reason for advanced timing is actually just to have the retarded part for starting and a nice calm idle
it is the other 2 marks that you want to have lined up at the elevated RPM's
you can even watch the advance marks move as you raise rpm's
at a certain rpm level they will stop advancing proly in the 2500+ range
getting it centered in the marks is what you are aiming for, towards the left all the way on the 2 marks should be fine and maybe the best with stock pistons
even further advanced is territory for more experienced tuners
you get into a situation where knock can occur, with too far advanced and that is very destructive
most race engines have a more efficient combustion chamber with a precision squish that helps turbulence, and speeds up the burn so there are a ton of factors
but modern ignition with the advance on a rising curve is the hot setup
 
Re: "Patina" The 1973 CB175 Cafe Racer


xb33bsa said:
the f mark is for at idle speed and or static
the reason for advanced timing is actually just to have the retarded part for starting and a nice calm idle
it is the other 2 marks that you want to have lined up at the elevated RPM's
you can even watch the advance marks move as you raise rpm's
at a certain rpm level they will stop advancing proly in the 2500+ range
getting it centered in the marks is what you are aiming for, towards the left all the way on the 2 marks should be fine and maybe the best with stock pistons
even further advanced is territory for more experienced tuners
you get into a situation where knock can occur, with too far advanced and that is very destructive
most race engines have a more efficient combustion chamber with a precision squish that helps turbulence, and speeds up the burn so there are a ton of factors
but modern ignition with the advance on a rising curve is the hot setup


Ooook I think I understand now. So at idle, the timing light should show me firing at the F mark. As I increase the RPM, the frozen image at the pointer will move clockwise toward the 2 advance marks and we want it to freeze between the lines around 2500-3000 rpms. So there will be a time between idle and higher engine speed where the pointer will be in the 30-whatever degree space between F and the full advance marks? It will travel from the F to the 2 lines as engine speed increases?
 
yes you got it ;)
you should be able to tell at what rpm it stops advancing as well
get the timing set then rev it up a bit more and verify that it wont go any more
 
Re: "Patina" The 1973 CB175 Cafe Racer

Well first before I get into the details, let me jump to to good stuff...thanks to you guys' help she is timed, pulls to the redline (whatever that is on my unmarked gauges), and cruises at 60 around 6000 RPMs...much more room to play.

Ok. So that was hands down the most stressful experience of this whole bike building ordeal . I bought a timing light and the instructions say not to hook the light up while it's running. So imagine me running to bump the bike off, gripping the gun in my teeth, holding the cords that are connected to the battery in my hand and bumping this thing off. Man.

The oil shower wasn't that bad, but after while she started to smoke because she was running low I guess. She was getting hot. Anyway before I cut her off, I had my fox pull her to 3k then to 4k and the static mark held right in between the lines. Smack dab inbetween. I guess I could adjust and have it closer to the first line. But I'll go back and adjust the static timing and make sure it's hitting the F, then that should correspond to me falling on the first advance line during dynamic timing but I'll check to make sure.

So then the story continues...I ran it about 200 yards and it died on me. I coasted it back and found that the little screw holding my red fused power wire had wiggled loose and the wire came unattached from the toggle! No power. So I tried to connect it back, forgot the ignition was on and BOOM! Backfire and electric shock. That hurt. Won't do that again.

After that, got it all buttoned up and took it for a 5 mile ride up the road. She pulls to the redline in all the gears and I had her cruising at 60 for a mile or so. She feels very stable surprisingly. I need to work on the idle BAD. She isles around 2500-3k. So I need to play with the screws a bit.

Otherwise! I'm traumatized and super excited!!!
 
You are getting there. Good job.

The range of advance is related to the stops (non adjustable) on the advancer. If it's worn, it may advance more (or less) than it's designed to. That means that sometimes timing can be set at idle (F mark) and it will be out at full advance and so on. That's why idle setting is less important than higher speed. If it's spot on at 3-5k, then leave it alone.

On race bikes we usually set the timing at full advance and leave it fixed there. That might be at 35 degrees or maybe 42 or more on a methanol burner, so when we start the bike we have way more advance than we need, but the bike never runs at low revs once it's fired up, so we don't care. We move off with maybe 4k for a slow ride out of teh pits and maybe 8k or more in a race start and a race bike rarely gets below 6k or so. And we want it to be spot on at speed, so sloppy automatic advance units have no place on a race bike, but are useful on the street. On a CB160/175 we usually mount a DYNA S trigger on the crank nose for accurate timing. That's not good on the street though. :-)
 
Re: "Patina" The 1973 CB175 Cafe Racer


teazer said:
You are getting there. Good job.

The range of advance is related to the stops (non adjustable) on the advancer. If it's worn, it may advance more (or less) than it's designed to. That means that sometimes timing can be set at idle (F mark) and it will be out at full advance and so on. That's why idle setting is less important than higher speed. If it's spot on at 3-5k, then leave it alone.

On race bikes we usually set the timing at full advance and leave it fixed there. That might be at 35 degrees or maybe 42 or more on a methanol burner, so when we start the bike we have way more advance than we need, but the bike never runs at low revs once it's fired up, so we don't care. We move off with maybe 4k for a slow ride out of teh pits and maybe 8k or more in a race start and a race bike rarely gets below 6k or so. And we want it to be spot on at speed, so sloppy automatic advance units have no place on a race bike, but are useful on the street. On a CB160/175 we usually mount a DYNA S trigger on the crank nose for accurate timing. That's not good on the street though. :-)

Thanks Teazer. Quick question for you. Is there any other way to verify oil to the top end other than opening a tappet cover when it's running or looking immediately after it's shut off for oil droplets?

Last time I tried while it was running at the tappet covers and got sprayed pretty good. So you are wondering why I'm asking the question since that is evidence I'm getting oil up there...ha

I was hearing a noise at the top end, that may be completely normal. It's not loud, sounds consistent with the sounds the pods are making pulling air in. I'm actually wondering if I'm getting them mixes up and don't have a problem at all.
 
Loosen the nuts on the studs that the oil flows up - just a little - and oil should seep out. All that tells you is that there's oil under pressure in there. You really want to know if the rockers are getting oiled as well as both end caps. I'd be tempted to crack the tappet covers and fire up the motor. Then loosen them one at a time to see that they are all oiled. You would also need to crack the screws loose on each end cap (tower) to be sure that oil is coming through.

Or just run it and keep your fingers crossed like the rest of us do. :-)
 
Re: "Patina" The 1973 CB175 Cafe Racer


teazer said:
Loosen the nuts on the studs that the oil flows up - just a little - and oil should seep out. All that tells you is that there's oil under pressure in there. You really want to know if the rockers are getting oiled as well as both end caps. I'd be tempted to crack the tappet covers and fire up the motor. Then loosen them one at a time to see that they are all oiled. You would also need to crack the screws loose on each end cap (tower) to be sure that oil is coming through.

Or just run it and keep your fingers crossed like the rest of us do. :-)

Well I know that I'm certainly getting oil at the front left tappet cover....if you're standing over the bike. I'll have to look at the flow map to see what would prevent me, if anything from getting oil to the other side.
 
Re: "Patina" The 1973 CB175 Cafe Racer


xb33bsa said:
on some of these side case gaskets however it is advantage to bond the gasket to one side so that future removal of the case is less likely to bust the gasket

XB, if the surface looked good to the eye but leaks at that location , would you be better off sealing both sides?

I've never been able to take a case cover off without having to replace the gasket because of sticky spots and stuff.
 
Back
Top Bottom