"Patina" The 1973 CB175 Cafe Racer

Re: "Patina" The 1973 CB175 Cafe Racer

1sttimer said:
Wear your play clothes...
Not sure if you seen Texas build a plastic cover. I'm gonna do the same but I have a buddy who makes moulds for slot car bodies. He places a thin acrylic sheet it. Heating element is above it. Soon as the sheet Starts to droop he shut off the element and vertically lowers onto a vacum table with lots of holes and within 15 sec it's done. One I make the mould I will make them availble.
 
Re: "Patina" The 1973 CB175 Cafe Racer


cafe mike said:
Not sure if you seen Texas build a plastic cover. I'm gonna do the same but I have a buddy who makes moulds for slot car bodies. He places a thin acrylic sheet it. Heating element is above it. Soon as the sheet Starts to droop he shut off the element and vertically lowers onto a vacum table with lots of holes and within 15 sec it's done. One I make the mould I will make them availble.

Sign me up.
 
Re: "Patina" The 1973 CB175 Cafe Racer

Anyone know the torque spec for the left aand right crankcase covers? Looked through the manual but I guess keep over looking them. It only gives a diagram of bolt locations.
 
Re: "Patina" The 1973 CB175 Cafe Racer

So I've noticed it only leaks after the engine gets hot. Pretty dang bad too. After it cools off there's not really any leaking..maybe a drop.


Had her at WOT in 5th and it was still pulling but it would have taken me another mile to get to 70....and it felt like it was starting to get hot so I need to figure out some type of sensor or something. And I had a little smoke coming from the exhaust for a split second only visible at idle and then it stopped.
 
no tighter than 60in/lb
maybe there is a crack that opens when hot
some powder to find the crack use talc not cocaine
the "sensor" you use to figger overheatin' is a plug reading
on a wot run pull in clutch and hit the kill,then pull plugs for a look
 
Re: "Patina" The 1973 CB175 Cafe Racer


xb33bsa said:
no tighter than 60in/lb
maybe there is a crack that opens when hot
some powder to find the crack use talc not cocaine
the "sensor" you use to figger overheatin' is a plug reading
on a wot run pull in clutch and hit the kill,then pull plugs for a look

Lotta good nuggets in this post. Thanks man. I'll give all that a shot. I'm looking for fuel air condition on the plugs? Is that considered a proper chop? Need new plugs?
 
Re: "Patina" The 1973 CB175 Cafe Racer


Duchat said:
If I could afford cocaine I would pay someone to fix my bike.

Amen brother!! Especially if I could afford it enough to smear it on a motor.
 
sniff sniff, new plugs make it easier to read condition
yeah go wot for at least a 1/4 mile slight uphill is best
kill it quick and you are looking for color
 
What you are looking at are the electrodes for signs of overheating. Use a jewelers loupe or big assed magnifying glass to see how the side and center electrodes look. If they are burned clean for too long, that's an indication that combustion temperatures are too high - could be wrong plugs, too much advance or too lean.

They won't show signs of poor heat removal though or of oil breakdown - only if there's excess heat generated in the combustion process.

Take a digital pyrometer with you and check around the head when you do the plug chop to see where is hottest and how hot it is.
 
Re: "Patina" The 1973 CB175 Cafe Racer


teazer said:
What you are looking at are the electrodes for signs of overheating. Use a jewelers loupe or big assed magnifying glass to see how the side and center electrodes look. If they are burned clean for too long, that's an indication that combustion temperatures are too high - could be wrong plugs, too much advance or too lean.

They won't show signs of poor heat removal though or of oil breakdown - only if there's excess heat generated in the combustion process.

Take a digital pyrometer with you and check around the head when you do the plug chop to see where is hottest and how hot it is.

It's pretty cool that a 1/4 mile run can show that much on the plugs. Is there anything that plugs you run every day can tell you or are they pretty useless because there are all kinds if running and throttle conditions mixed in?


Sent from my iPad using Tapatalk
 
Re: "Patina" The 1973 CB175 Cafe Racer

Gentlemen can one of you remind me what's about to happen when I take this left side cover off in reference to the clutch mechanism? Is the adjustment slotted cylinder going to stay attached to the case when the side cover comes off or is it going to pull off with the cover?

hadydude.jpg


eda4y2a3.jpg
 
Re: "Patina" The 1973 CB175 Cafe Racer

Ok never mind I got it. I was expecting to see a crack in the case or cover but from what I can see, there's nothing .

One thing I noticed is that the gasket came off very easily. In huge sections. So I would imagine there was no sealer used. I was thinking it was going to be a pain to get the gasket off like the original one but I can pretty much get it off with my nail.

I'll have to readjust the clutch now I guess. Didn't expect that. I thought it would go right back into place.

The new gasket should be here soon.

eherasym.jpg


eqynygav.jpg


ve9a3utu.jpg


ypytaga7.jpg
beda4y2u.jpg
 
no reajusting of the clutch should be needed as long as the gaskets are close to the same
while you are in there i would pull of the rotor and remove all the uneeded garbage on it
 
Re: "Patina" The 1973 CB175 Cafe Racer


xb33bsa said:
no reajusting of the clutch should be needed as long as the gaskets are close to the same
while you are in there i would pull of the rotor and remove all the uneeded garbage on it

I was wondering what all that black crap was. It is hard. Nasty deposits from years if sitting maybe?
 
Re: "Patina" The 1973 CB175 Cafe Racer

1sttimer said:
I was wondering what all that black crap was. It is hard. Nasty deposits from years if sitting maybe?
Everyone brings it home new. Hears all the great stories about how great they are. And never clean the trap. It's labor intensive, or unknowingly overlooked
 
Re: "Patina" The 1973 CB175 Cafe Racer

1sttimer said:
I was wondering what all that black crap was. It is hard. Nasty deposits from years if sitting maybe?

on the stator well it will hacve deposits be careful trying to clean that if it is stuck just leave it alone
clean gasket surfaces to bare metal 100%
what i was talking about is the sprocket and related bits bolted to the stator rotor
 
Back
Top Bottom