"Patina" The 1973 CB175 Cafe Racer

Re: "Patina" The 1973 CB175 Cafe Racer


xb33bsa said:
you may need more slack in the single cable adjuster at the grip
did i not fully cover bench synching already?

Bench sync = Popsicle stick then yes. We're good there.
 
Re: "Patina" The 1973 CB175 Cafe Racer

1sttimer said:
Bench sync = Popsicle stick then yes. We're good there.
popsicle stick gets the cable pull even you still nede to synch the cable slack idle screw position as it pertain =s to the idle slide opening
 
you can do it thusly back off the idle speed screws the ones that lift the slides...
use the single cable adjuster at the throttle grip to achieve an idle and then carefully one side at a time sneak up on the idle speed screw adjust until it contacts the slide and you hear a change
then back of on the single cable adjuster to acheive slack and then back of each idle speed screw evenly to lower idle
 
Re: "Patina" The 1973 CB175 Cafe Racer

xb33bsa said:
popsicle stick gets the cable pull even you still nede to synch the cable slack idle screw position as it pertain =s to the idle slide opening
In other words. Back out the idle screws. Then see if you have slack in the cables. Pull on the cable and make sure they move up and down a 1/16". Does the bike rev up when you turn the bars at all. Do you have slack in the throttle tube. Again back off the idle screws. Check cable slack. If not turn in one time the cable adjuster for each carb. Then play with Popsicle sticks.
 
Re: "Patina" The 1973 CB175 Cafe Racer

cafe mike said:
In other words. Back out the idle screws. Then see if you have slack in the cables. Pull on the cable and make sure they move up and down a 1/16". Does the bike rev up when you turn the bars at all. Do you have slack in the throttle tube. Again back off the idle screws. Check cable slack. If not turn in one time the cable adjuster for each carb. Then play with Popsicle sticks.
no once you set the carbs even with the pop stick you dont want go back and mess that up
 
xb33bsa said:
you can do it thusly back off the idle speed screws the ones that lift the slides...
use the single cable adjuster at the throttle grip to achieve an idle and then carefully one side at a time sneak up on the idle speed screw adjust until it contacts the slide and you hear a change
then back of on the single cable adjuster to acheive slack and then back of each idle speed screw evenly to lower idle
My bad. I understand your way. I have never tried this way. Can't wait. Try it. Thanks
 
Re: "Patina" The 1973 CB175 Cafe Racer

xb33bsa said:
no once you set the carbs even with the pop stick you dont want go back and mess that up
I'm more trying to translate that his cables might be tight. So as a base line make them loose and redo everything you said
 
Re: "Patina" The 1973 CB175 Cafe Racer

xb33bsa said:
no once you set the carbs even with the pop stick you dont want go back and mess that up
I sync them as well. But I would rather have the cables have slack ( but making sure I hit wot ) let it the slides rest on the idle screw. I just count the exact turns on the cable adjusters at the top of carbs
 
Re: "Patina" The 1973 CB175 Cafe Racer

This guy...?

First off I noticed that my throttle cable is routed TERRIBLY. I have no idea why I did that. The section before the split is going a much longer route than it had to. I'll adjust that first. Gaskets are coming in tomorrow and loctite by Tuesday. You can't buy 518 locally....so I'll try all this when I get her together. Thanks for holding my hand through it

numaja4e.jpg
 
Re: "Patina" The 1973 CB175 Cafe Racer

1sttimer said:
This guy...?

First off I noticed that my throttle cable is routed TERRIBLY. I have no idea why I did that. The section before the split is going a much longer route than it had to. I'll adjust that first. Gaskets are coming in tomorrow and loctite by Tuesday. You can't buy 518 locally....so I'll try all this when I get her together. Thanks for holding my hand through it

numaja4e.jpg
I would make sure you have play in the throttle tube. Adjust cable if not. Then move to the cables and see if the cables on top of both carbs have play when when the idle screws are backed out till they make no contact with the slides
 
Re: "Patina" The 1973 CB175 Cafe Racer


cafe mike said:
I would make sure you have play in the throttle tube. Adjust cable if not. Then move to the cables and see if the cables on top of both carbs have play when when the idle screws are backed out till they make no contact with the slides

I definitely have play in the tube. I can twist it 5 degrees or so before it actuates anything. Kind of annoying if you're concentrating on it but not noticeable in riding. I actually thought something was wrong until y'all said that's something I should have.
 
yep back off that adjuster at the throttle quite aways, untill you are all through with the other adjustments
this adjuster is your very last one to be done (small amount of free play in the single cable/throttle grip)
 
Re: "Patina" The 1973 CB175 Cafe Racer

I've never seen gaskets made of this material...it's not paper. I guess it's similar to the green kind?

Says "interface solutions" on them. They feel like a thin rubber almost but not as malleable.


e4ute6u4.jpg
 
Re: "Patina" The 1973 CB175 Cafe Racer


cafe mike said:
Are you charging. Because I'm not.

Uh oh, yeah I had bad grounds. After I fixed all my grounds I am charging like a champ.


Sent from my iPhone using Tapatalk
 
Re: "Patina" The 1973 CB175 Cafe Racer

Any of you guys that own a 175 or 200 see this issue on the left side engine gasket? It's like the gasket steps up and misses the gasket surface once you get closer to the sprocket. This IS beyond the "circle" where the stator sits that should be sealed. The reason I ask is because this is exactly where I was leaking and I am curious if the gasket design was the issue. But I'm thinking that as log as the "circle" is sealed then it shouldn't matter what happens to the right of that right?

See pics..I'm pointing at the "circle" I'm referring to on the last pic which refers to the open stator circle. Anything right of that shouldn't matter if it's sealed or not right?

dy4ajenu.jpg


tu3umu3u.jpg


ny9epepu.jpg
 
Re: "Patina" The 1973 CB175 Cafe Racer

Has a legit website at least :)

I just can't wrap my mind around the design of that. Even from a consumer perspective it's concerning.
 
Back
Top Bottom