"Patina" The 1973 CB175 Cafe Racer

1sttimer said:
Is there any opposition to using motor oil as foam air filter oil? UNI's website says to not do that because it can damage the vehicle, but I'm having a hard time seeing as to how that is possible. Would K&N oil work as well or are they different formulations and work differently?
I use no-toil. It has a solvent so the none green formula stinks good. Make sure you get the cleaner. It's the only cleaner that will get the oil out, it's powder form. Once you mix with warm water the old oil falls right off. And your up and running in 15min instead of couple hours.
 
Re: "Patina" The 1973 CB175 Cafe Racer

WHY DOES ALUMINUM HAVE TO BE SO DANG SENSITIVE!??

looks like I have a stripped case thread below oil level. And two others below oil level are starting to go.

Is that even repairable??

I have the gasket installed with tons of sealant on both sides (luckily) so I'm just going to see if I managed to get a good seal all the way around and go with it. I'll let it sit overnight and cure and hope for the best.
 
Re: "Patina" The 1973 CB175 Cafe Racer


cafe mike said:
Wait and see.

Oh for sure. I'll have oil in it fired up tomorrow night. We shall see.


Sent from my iPhone using Tapatalk
 
Re: "Patina" The 1973 CB175 Cafe Racer

On another note, as soon as I turn the ignition on giving power to the coil, both plug caps pop, without a spark plug connected. And when I tried to turn my ignition on to see if my lights would come on, they didn't. Gauge lights dimly lit. Battery read 10.4. Charged it
For a second and everything worked fine afterwards. Leaving it on the tender now.


Sent from my iPhone using Tapatalk
 
Re: "Patina" The 1973 CB175 Cafe Racer

1sttimer said:
On another note, as soon as I turn the ignition on giving power to the coil, both plug caps pop, without a spark plug connected. And when I tried to turn my ignition on to see if my lights would come on, they didn't. Gauge lights dimly lit. Battery read 10.4. Charged it
For a second and everything worked fine afterwards. Leaving it on the tender now.


Sent from my iPhone using Tapatalk
Electronic ignition sent a signal to coil. Flutter. Crazy that you heard it. Zap
 
Re: "Patina" The 1973 CB175 Cafe Racer

Well, got the gasket installed and fired her up. Not a drop, from the gasket that is.

I took her for a spin and held her at WOT for a few runs through all the gears from an engine break in article I read, it ran fine for a few runs and pulled hard.

Then I tried to come home, revs dropped. I had to keep the RPMs way up to limp it home. It wasn't that I wasn't charging because all my electronics work fine. But now I noticed when I got back that I was dripping a few drops of oil out of my carb overflow.....

I have no idea what that means or how that's even possible, but that can't be good.
 
Re: "Patina" The 1973 CB175 Cafe Racer

Oh wait wait wait. My vent hose from my head runs parallel to my drain hose from the carb. The droplet of oil was running out of the head hose and transferring on to the carb overflow hose and dripping hahaha
 
Re: "Patina" The 1973 CB175 Cafe Racer

Any ideas about why I lost power after a few WOT runs? Could I have overheated it that fast? I really need to get a point and shoot thermometer gauge.


Sent from my iPhone using Tapatalk
 
Re: "Patina" The 1973 CB175 Cafe Racer

1sttimer said:
Any ideas about why I lost power after a few WOT runs? Could I have overheated it that fast? I really need to get a point and shoot thermometer gauge.


Sent from my iPhone using Tapatalk
overheating that lil 175 at wot enuf to loose power would have been a smokey smelly deal
check that you fuel vent is good on tank cap
did it syart popping and missing ?
 
Re: "Patina" The 1973 CB175 Cafe Racer


xb33bsa said:
overheating that lil 175 at wot enuf to loose power would have been a smokey smelly deal
check that you fuel vent is good on tank cap
did it syart popping and missing ?

I am smoking a little bit, but I believe that's due to my rings not being seated yet. I think Texasstar had the same issue for a little while.

It was popping a little bit wanting to hesitate a little. Not sure what a miss feels like or sounds like but it was sputtering some.

Also, the vent comment is interesting. I have an ebay replica gas gap but I don't see how it could vent. The reason I say this is that I was able to turn the tank upside down and change out the petcock with gas in the tank without too much leaking beyond the cap.
 
Re: "Patina" The 1973 CB175 Cafe Racer

I've been reading around and it sounds like the tank thing is promising. I'm about at 1/4 tank now which would make sense if that's the problem. I'll fill up and see if it goes away.

Also I sprung a leak on one of my fuel filters at the connection of the halves. Maybe it melted on the head? Idk. I'm going to run without them for a bit just to eliminate that as a variable.


Sent from my iPhone using Tapatalk
 
Re: "Patina" The 1973 CB175 Cafe Racer

How do race bikes vent their tanks? A lot of times I see what looks like fuel hose coming out of a port in the cap. My old 4-wheeler had that with a plastic fuel tank.

Vent to atmosphere instead of pressure venting?

y9ysysah.jpg



Sent from my iPhone using Tapatalk
 
no such thing as a pressurised gas tank :o not on any old sickles anyway
they ALL vent to atmossfear lolz is your tank making a foo noise when you pull off the cap ?
 
Re: "Patina" The 1973 CB175 Cafe Racer


xb33bsa said:
no such thing as a pressurised gas tank :o not on any old sickles anyway
they ALL vent to atmossfear lolz is your tank making a foo noise when you pull off the cap ?

Ok negative pressure in relation to the atmosphere (though there's no such thing as negative pressure). Vacuum. I thought that the cap vent was actuated when suction inside the tank increased to a certain level. Almost like a pressure release but opposite for vacuum.
 
Re: "Patina" The 1973 CB175 Cafe Racer


xb33bsa said:
no such thing as a pressurised gas tank :o not on any old sickles anyway
they ALL vent to atmossfear lolz is your tank making a foo noise when you pull off the cap ?

I didn't mean there was positive pressure within the tank :) I just was wondering if it was constantly vented to atmosphere rather than the suction within the tank having to overcome a valve to actuate. I think my blaster tank just had a hose and a through hole through the cap. My 175 cap has some sort of valve in there because I can turn the tank upside down with fuel in it and it doesn't come pouring out.
 
not really a valve it is supposed to be 100% vented to atomsfear suk or blo
try running with the fool level low, cap lose
 
Re: "Patina" The 1973 CB175 Cafe Racer


xb33bsa said:
not really a valve it is supposed to be 100% vented to atomsfear suk or blo
try running with the fool level low, cap lose

Sounds like a blockage of some sort if liquid won't go through. It was cheap of Ebay. Easily could be a defective part.

I'll run without the cap.
 
Back
Top Bottom