small CL 360 project

Lookin and soundin sweet.

I had an untitled/bad motored pile of a CB360 last spring. Here is a pic mocked up with a CB500T tank and front end that I had laying around. Also a homemade exhaust from who-knows-where. I never put it together because the motor was shot and I had no title. But I just picked up a '74 CB360 with a title and frozen motor. It took about a day of soaking the cylinders with WD and 5 minutes rocking her back and forth in gear and the motor is free and seems to have good compression, so my project is back on ;D If it wasn't -2F in the garage, that is.

I'll be watching your thread and robbing ideas;) Thought you might want to see a different tank to throw into the idea pot. I have an old CL350 tank that I may use as part of the tail section. Time will tell.
 
Thanks man, The video is kind of a big hoopla production of nothing, but I said what the heck. It didn't take me any longer to add a title and music than it did to post the thing up. LOL. Anyhow, I hope at some point I have something positive to contribute to this web site. There are some really incredible builds on here.
I really like the looks of that tank on your bike. Thank you for posting it. I should be able to get some measurements from your photo. Does any one know if the CB 500 tank is about the same size as 750s?
Looks like you've got lots of help with your build. cute kid!
It took about a day of soaking the cylinders with WD and 5 minutes rocking her back and forth in gear and the motor is free and seems to have good compression
My neighbor has a 70's Honda 750 that he did this to. It took about a week of soaking to free it up. He has been riding it for the past 5 years with no problems. These motors seem to be pretty tough.
I'm gonna head out to my garage and grab a tape to take a few measurements. I dont have my seat yet but I do have the measurements. I won't be out there very long though. It's cold here too, about 6*F. Where are you located??
 
I'm in Sylvania, Ohio near Toledo. It is 7 tonight but supposed to warm up a bit over the next couple of days.

I have a couple CB500K models if you need some measurements.

IMHO the best thing about these bikes and sites like DTT is that they are for everyone. The bikes are cheap enough for those of us on slim budgets, the parts are plentiful and they run forever. And people are welcome whether it is a $200 rat rod like my '71 CL350 or a beauty that ChrisF puts up. Did I mention that they look cool in a thousand different ways? That tank I got is all beat up, but it is clean inside and good for mockups and ideas. When the time comes (March or so) maybe I'll get to the make it pretty stage.
The plan right now is to make it run, mock it up, make it ride and then make it pretty. I don't really care as long as it is fun ;D
 
Oh I love that tank SOS. I'm using the same one on my project. I wish I had a running motor. I do like SOS and buy rust buckets. I admire the rate at which your working on this project troy. Sounds awsome. This is a great site isn't it.
 
Hey IMOALE I love SOS's tank too. I'll be going to a friends house in a few days to look through his old tanks and that tank is one that is on my list. I also love this site. Great people, cool projects, and tons of information.
As for the speed of my project, It's been pretty slow. Everything is in mock up stage for now. I received my seat on Friday and Now I need a tank. It seems so much revolves around these two items. I plan to weld a plate/brace for under the seat but I dont want to do anything until I know where everything goes. I'll also be making a battery holder. Once mock up is done I think I'm going to strip her down and paint the frame.
Hey SOS I was wondering if that tank is sitting in the front mounts or would the front mounts have to be moved? I realize the rear mount would have to be moved. Troy
 
The tank is on the front mounts. All I had to do was cut a 1/4" off each post because the tunnel on the 500T tank is narrower. Then I used some front tank rebbers from a '79 Suzuki GS550 because they are thinner, but you can just cut the 360 ones down too.

Hey, like an idiot I let the petcock from the 500T tank go. Does anyone have a spare? The threads on the tank have a larger diameter than the others that I have seen.

Later
 
Your bike is coming along nicely. Did you paint those shocks with zero rust paint? My shocks look like crap but I don't think I will be taking them apart like you did.
 
I knocked most of the rust off with a wire brush attached to a grinder on the outside of the spring and the rest of the spring got course steel wool. I then went to a finer sand paper something like 200. Then I cleaned and used self etching primer then painted with rustolium?? rattle can. It really made them look better without much effort. Just place the spring on the lightest setting then compress it with your hands. It helps if you have someone who can pop out the keepers. It also took two of us to put it all back together. All in all it really wasn't that hard. Troy
 
I received my bars and seat the other day so it inspired me to do a little more work on the bike. I decided to cut a few more tabs and other things off. I'd love to weigh what I've cut off because the bike feels a lot lighter. However, it might just be wishfull thinking. Here is a rear profile. I'm really starting to fall in love with these little bikes. I think the skinny tire on the back just rocks. Nothing is bolted down yet and I just wanted to get an idea where things will go.
DSC_0001.jpg

I think I'm going to weld the bar back on the back. I don't like the look with the frame just cut off. It looks unfinished that way.
I also decided to go with a speedometer instead of the tach. Right before Christmas my family and I took a trip to Pittsburgh to watch a concert. Anyway, during the trip it made me realize that knowing my exact speed might be important. You know, Do I just pull over and take the ticket or I was going fast enough that I better just keep going and not stop?? ;D
here is a photo of the speedometer. With just one support it looks like it kinda floats (might vibrate like hell though)
DSC_0012.jpg

Another photo of bars and speedometer. The bars are from Champ. I think it's a pretty good deal for $75.00 shipped. the chrome is easily scratched but I figure what the heck. They feel like they should be plenty strong enough.
DSC_0015.jpg

Tank sucks with this seat. I think this is about where the seat will go once I get a new tank. I left some of the side covers tabs on for reference point.
DSC_0019.jpg

There are lots of things out of place. By the look of these photos the bars are too straight and need to be adjusted back some. The headlight is held on with zip ties and all the wiring is help up with zip ties as well. I don't plan to relocate any wiring, battery holder or weld seat brackets until I get a tank. Once I get the tank I plan to use the factory seat hinge on the front of the new seat. I think I can cut it down and bolt it on the front so the seat can flip up from the rear. The the real work will begin.
 
Just picked up this tank from a neighbor. It will take a little work to make it work but I like it. I think has nice lines. It has a couple very small dents and some surface rust. the inside looks brand new. Anyone know what it is off of??
DSC_0037.jpg
DSC_0027.jpg
 
Thanks guys. I had a few friends over tonignt (all Hard core HD people)and they all wanted to sit on her. As soon as they sat down they got a huge grin on their faces ;D.
The tunnel on this thing was very small, but not after I took a hammer to it. Now I have room for the wiring. I also worked out a plan to mount it. The front tabs on the frame will be moved up about an inch and for the back I will weld a plate on the tank with a hole and a nut welded on. the frame will have a tab for a bolt. Anyhow, I stripped the tank and sanded a bit. Here are a few more photos for ya. Oh yeah, I stuck a knee pad on there to see how it would look. Knee pads or no Knee pads????
DSC_0031.jpg

DSC_0039.jpg

DSC_0044.jpg
 
Will they be at all funtional? Do you knees line up with the tank like that when you sit on your bike? I imagine they will, since you have a short seat a and a long tank. Are you putting rear sets on?
 
Yes the pads would be functional. My knees come right up beside them. However I think it will come down to looks. I would love to do rear sets. In fact it will be pretty uncomfortable without them. They will come down to funds.
I have electric in my garage now. The garage is brand new (2yrs), but I never had the time to wire it. So today I wired in a service panel and added a breaker box that contains 1-receptacle and a 220 receptacle for my welder. I had been running extension cords from the house, but now I have electric inside the garage! I added the temporary service panel I used when I built my house. It was just sitting around so I put it to use. I'm not sure when I will have the funds to finish wiring the garage , but I'm stoked. here is the service panel with the other box connected below it.
DSC_0076.jpg

So I welded up my pipes. I think I spent more time chasing holes than welding LOL. It's been about 2 years since I've welded. Funny thing is the last thing I welded was exhaust tips on my truck. Here are a couple welding photos. I first tacked up the pipes while on the bike then I took them off and finished them. It took a little while but I guess it's like riding a bike ;D.

DSC_0054.jpg

DSC_0065-2.jpg
 
One other thing to get welded next will be the tank. I'll be welding a flat plate across the back. It will cover up the hole behind the tank that the seat won't cover and it will be used as the rear mount. The tunnel is very narrow and the tank sits on top of the frame at the rear. I'll post up photos when I get it welded. Troy
 
Love the welding pics, really cool shots. I get so jealous when I see anyone welding, going to have to get one if I ever get any money.

What kind of dog do you have there, looks like a Dane. Nice looking dog.
 
Back
Top Bottom