small CL 360 project

Hey Troy,

What's your technique for using the silver epoxy paint? I shot some this weekend on my alternator cover. Started off with a couple light coats, but the paint wouldn't lay down smooth. Went on very rough, almost like that faux stone paint. Next few coats were shot on very heavy and helped to smooth out the first few coats but still ended up a little rougher than I would have hoped. Also, I didn't notice much tendency to run even with heavy coats, so I'm guessing heavier coats work best with this paint (this color anyway).

Thanks, CC
 
CC.. it is your prep or the temp that is the issue... what are you wiping the parts down with before shooting... what did you sand them down to before shooting? how cold is it where you are shooting it... this paint has a leveling mixed into it so it should lay smooth no matter what unless one of the above is not propperly done... are you laying coats after the 1/2 hour is up? light coats is the trick man, you lay it heavy and it will run like crap!
 
JRK5892 said:
how do those suckers look? did you have to weld them up? can you take a shot looking down the pipe!?
Had my muf shop expand my pipes about 1/16". you can't even tell there expanded. Very tight fit! Just drilled a hole in the back and put a self tapping screw. I'll grap photos at first chance. More than likely tomorrow. BTW those wr
e the $8 ones from JC whitney. later
Sorry guys but I've gotta run. I'll check back later tonight.
 
CCRider said:
Hey Troy,

What's your technique for using the silver epoxy paint? I shot some this weekend on my alternator cover. Started off with a couple light coats, but the paint wouldn't lay down smooth. Went on very rough, almost like that faux stone paint. Next few coats were shot on very heavy and helped to smooth out the first few coats but still ended up a little rougher than I would have hoped. Also, I didn't notice much tendency to run even with heavy coats, so I'm guessing heavier coats work best with this paint (this color anyway).

Thanks, CC

Yeah, I ran into the same problems and learned quite a lot through trial and error with that stuff. Very finicky paint. Cover everything, that stuff oversprays like crazy. Warm everything up inside, parts & the paint... Warm up your garage if possible, everything has to be AT LEAST 50 degrees. Make sure the surface is totally clean-- I had some filmy stuff rise to the surface (probably leftovers from the paint stripper when I took the first coat off to start over) and it looked terrible. Spray directly on metal, no primer. Recoat within 30min or after 1 week. It's all in the instructions but still a huge pain in the ass to work with in my experience.

After 3 weeks of trying to get it right on my wheels, I still have some work to do. Shit's tough as nails and looks great when done properly, though.
 
i wash all my parts in dish soap first to remove any stripper left... then i use either denatured alchole, prep, or acitione to wipe them down, hit them with a tack cloth and go to town... ALSO!!! let that can soak in warm water for about 30 min before shooting! it will really REALLY help it to flow out better!
 
How are you guys cleaning up your nuts and bolts? Do you just wire wheel them or what? I have a lot of rust on mine I was thinking I am going to have to wire wheel them and then paint them with that epoxy paint hows that sound? Or will it just chip off as soon as I wrench on it?
 
bolts will not last man, i wire wheel them and polish them... i powder bolts i need to handle a wrench... on my stem nut i painted a while back i put masking tape on the wrench and it worked ok...
 
troybilt said:
As for progress. I'm waiting on clutch push rod parts. the "screw" as its called in the man. is bent all to hell and doesn't allow the bearings to push the rod properly. As soon as It somes in things should roll pretty quick.
I received my VW mufflers. I left the pipes a little too long and the wrap needs to come up higher on the muflers. The tapper just looks too small when the wrap starts where it does. I'm hoping I can cut some of the tapper down and take the wrap a little farther out. I did brush the chrome and plan to clear coat it. Just something else for me to re-do. I'll also probable paint the bracket silver.
DSC_0809.jpg

DSC_0813.jpg

DSC_0814.jpg

hmmm i cant see these photos
 
CCRider said:
Hey Troy,

What's your technique for using the silver epoxy paint? I shot some this weekend on my alternator cover. Started off with a couple light coats, but the paint wouldn't lay down smooth. Went on very rough, almost like that faux stone paint. Next few coats were shot on very heavy and helped to smooth out the first few coats but still ended up a little rougher than I would have hoped. Also, I didn't notice much tendency to run even with heavy coats, so I'm guessing heavier coats work best with this paint (this color anyway).

Thanks, CC
Hey CC, Everything they said. The only thing I'd add is it sounds like you got some dry doses of flake. Same thing happened to me on my first can. You described it perfectly when you said that it almost looked like faux stone paint. I think having the can warm and shaking the shit out of it is key. If you don't shake it almost like every 5 seconds while spraying, the flake will seperate and you'll get small 'dry' blasts of flake and other bursts without any flake. So get it warm and shake the shit out of it. good luck
 
JRK5892 said:
CC.. it is your prep or the temp that is the issue... what are you wiping the parts down with before shooting... what did you sand them down to before shooting? how cold is it where you are shooting it... this paint has a leveling mixed into it so it should lay smooth no matter what unless one of the above is not propperly done... are you laying coats after the 1/2 hour is up? light coats is the trick man, you lay it heavy and it will run like crap!

I don't think prep or temp were the problems. Part was bead blasted, sanded, washed with dish soap and wiped down with acetone. Sprayed outside with temps between 60 and 70, and recoated in well under 1/2 hour. I've sprayed black with no problem, but the silver seems to be a different animal. Once I started using heavy coats things went much better, and running was no problem, so I'm thinking heavier coats are the trick with silver.

CC
 
The silver has a ton of micro flake in it. The only way I could get it to flow even was to almost constantly shake the crap out of it. My first can I had problems with burst of very heavy dry flake (you could almost see flake standing on end). I started shaking it alot more and never had any more problems.
Hey man is that you on the kite? Very cool picture! Everyone has cool avatars. I think I need a new one. Troy
 
JRK5892 said:
how do those suckers look? did you have to weld them up? can you take a shot looking down the pipe!?
Damn Joe, I'm gonna have to get my microscope out. I thought I took the largest pics on the Ton. ;D Just kidding. Do you need my to take more of the pipes? No problem, just let me know.
I really don't like the way they look. I hope to shorten it all a bit and run the wrap to where it tapers. Just let me know if you want more photos. Troy
 
i think that they look good man! i would wrap them like oyu say to where they start to get wider, that would tie it in a bit more for you i think... i like them... i just want to see a shot down the pipe so i can see how they are baffeled, give me an idea of if my home made baffles are about the same or not... OOH YA, dont change your avitar, it is one of my favorites!
 
CCRider said:
I don't think prep or temp were the problems. Part was bead blasted, sanded, washed with dish soap and wiped down with acetone. Sprayed outside with temps between 60 and 70, and recoated in well under 1/2 hour. I've sprayed black with no problem, but the silver seems to be a different animal. Once I started using heavy coats things went much better, and running was no problem, so I'm thinking heavier coats are the trick with silver.

CC

cool! i have never shot the silver so i will bear that in mind for when i use it... i really like the look it has!
 
JRK5892 said:
i think that they look good man! i would wrap them like oyu say to where they start to get wider, that would tie it in a bit more for you i think... i like them... i just want to see a shot down the pipe so i can see how they are baffeled, give me an idea of if my home made baffles are about the same or not... OOH YA, dont change your avitar, it is one of my favorites!
I'll grab up a photo later this morning. glad your dig the avatar. Guess I has having a "grass is always greener" moment.
My oldest son called and asked if I decided on paint. I told him that Wife picked up 2 cans of black last night at Lowes (I'm pretty rural. Its about 45 min each way) . He was not happy. He thinks I should try the silver first. "Everyone does black and the silver paint is kick ass".
 
troybilt said:
Hey man is that you on the kite? Very cool picture! Everyone has cool avatars. I think I need a new one. Troy

That's my brother under our homemade bamboo and plastic hang-glider. I'm towing him with my 125 Honda Elsinore. Circa sometime late '70's. Sometimes it's hard to believe we survived our youths.

CC
 
CCRider said:
That's my brother under our homemade bamboo and plastic hang-glider. I'm towing him with my 125 Honda Elsinore. Circa sometime late '70's. Sometimes it's hard to believe we survived our youths.

CC
Wow! That's crazy stuff. Did your parents know what you were doing and who took the photo? That is so cool. Dangerous, but cool!
 
troybilt said:
I'll grab up a photo later this morning. glad your dig the avatar. Guess I has having a "grass is always greener" moment.
My oldest son called and asked if I decided on paint. I told him that Wife picked up 2 cans of black last night at Lowes (I'm pretty rural. Its about 45 min each way) . He was not happy. He thinks I should try the silver first. "Everyone does black and the silver paint is kick ass".
well that my friend i think should over rule us all! silver it is! only reason i said black is because i realy like when people make the frame POP showing that it is diff, that is why i say black on the tank, to make that frame POP!
 
I still like the black just as well and I'm still on the fence. The vote is now tied 4-4. Guess I need to end all this drama and just paint the damn thing. ;D
 
Back
Top Bottom