small CL 360 project

Tim said:
Just throw a 'www.' and '.com' on either side of your plate and we're golden ;)
wish I could, but I'm limited to 8 characters :(

Herm, Thanks for the link but they list them as unavail. too.
I need about $5 in parts. I have a lever and gasket coming, but I need the spring, retainer and bolts....this sucks
pitcockparts-1.jpg

I'll grab a couple of progress photos soon
 
Keep in mind, we *BUILD* shit here......
Chances are pretty good that you could if you put your mind to it, make the spring you needed from a hardware store part, same with the screws...chances are pretty good that even if you couldn't find exactly what you need in a well stocked Ace Hardware, you could get something a little long and cut it down. Same for gaskets and diaphragms (nytril is your friend).

Your other option would be to replace it with a universal petcock and make an aluminum adapter.
 
CB200 tank right? The fiche I looked at on their site looks different than the one you have... they do have these parts. They don't have them in stock, but if you call they will order them for you.
 
Swagger said:
Keep in mind, we *BUILD* shit here......
Chances are pretty good that you could if you put your mind to it, make the spring you needed from a hardware store part, same with the screws...chances are pretty good that even if you couldn't find exactly what you need in a well stocked Ace Hardware, you could get something a little long and cut it down. Same for gaskets and diaphragms (nytril is your friend).

Your other option would be to replace it with a universal petcock and make an aluminum adapter.
I know I sound all pissy, but i'm over budget/time/patience, haha. This should have been a ten minute fix, but now its an issue I wasn't planning on.

Herm, Yes its CB200T I gave them a call and the retainer clip and the spring are not avail. Like Swager said, I'll figure something out.

Have a little bit of progress photos
Laid more fiberglass on the seat. It was a little flimsy. Now its pretty stout.
DSC_0979.jpg


Rear view: license plate bracket mounted. Still need to add running lights for the plates
DSC_0969-1.jpg


Clear coat on the tail. Turned out amazing! The two stage clear is so so much harder than rattle can clear. Plan on door guard edging around the bottom rim and the hole at the bottem is for a retainer for the wires.
DSC_0959-1.jpg


Homemade Herm rear set.
I had a bolt mounted above for my old shifter but with the new bearing it allowed me to mount the shifter with the peg. I cut the bolt off, but I'm going to wait awhile to grind it back smooth and repaint it.
I used a piece of water pipe as the rear spacer. The bolt is grade 8 and the washers are hardened. Drilled a hole for the toe piece to slide through and welded it.
DSC_0954.jpg


Here is the spray bottle, clear and hardner I got at NAPA. The bottle was about $5 and the aerosol refil was $3
DSC_0981.jpg
 
A little luck my way and I picked up a gasket rebuild kit for the pitcock. I also have a pitcock lever and gas tank cap gasket on its way from honda. I'm still looking for a retainer plate and spring for the pitcock.
This guy has a good many NOS Honda parts
http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?ViewItem&item=300296899101
 
troy,
I might have missed it in this thread, but are you having any problems with your straight pipes? I cut the mufflers off my cl360, and on another thread some think it may burn a hole in a piston. what do ya think?

Jay
 
Hey, thanks Big. If I had it to do over I would have bought a simular light from advance auto (I think its still under 10-15 bucks). It looks almost the same except it has a bunch more LEDs. You would have to run a capacator on one of the wires to use it as both a brake and running light. If you end up with something like the Advance auto one check with JRK and he can help explain how to wire it.

Hey Jay, I don't expect any real problems with the exhaust. I did use the VW glass packed tips which should add some resistance, but I'm also running v-stacks. I've not started it yet since my mods however I plan to do no carb mods at first just to see how it runs. I will say that my ol man expressed concern over cut mufflers and holes in a piston.
Chris has a bunch more experience on this matter here: http://www.motofiaccone.com/moto/39-cb360-cafe-racer i believe he cut his mufflers off and is running pods with no carb mods and has reported no real problems. At worst I expect I may have to change out a couple of jets in the carbs. Hope this helps. Troy
 
keep in mind, my comments above were meant as encouragement, not a diss.......
Good luck, can't wait to see how it all comes out!
 
Swagger said:
keep in mind, my comments above were meant as encouragement, not a diss.......
Good luck, can't wait to see how it all comes out!
Hey Swag not taken as a diss at all. I just want this thing to be done and I was being all pissy about having a problem with the pitcock, so man I apologize for whining like a little bitch.

Last night I rechecked every nut and bolt on the bike. Bar mirrors arrived today and got those mounted up. Tank is sanded and ready for clear. So clear the tank, fix the pitcock, fill with oil, and she should be ready to start and hopefully ride. Not going to fill with oil until I take it out of the living room though. Temps are in the low 40s today so I may wait till tomorro to clear the tank. hopefully pitcock gaskets will be here soon. I still need that spring and retainer for the pitcock. Hopefull I will figure womething out. Troy

one more thing. My tag Lady called and informed me that I'm allowed only 6 characters on the vanity tags :( Here's what I'm thinking: TON UP or TONACE . You guys helped me build this bike so its only right to have you help me with the tags ;D So any more suggestions???
 
troybilt said:
Hey, thanks Big. If I had it to do over I would have bought a simular light from advance auto (I think its still under 10-15 bucks). It looks almost the same except it has a bunch more LEDs. You would have to run a capacator on one of the wires to use it as both a brake and running light. If you end up with something like the Advance auto one check with JRK and he can help explain how to wire it.
mods and has reported no real problems. At worst I expect I may have to change out a couple of jets in the carbs. Hope this helps. Troy

Think I will be running as both a brake and running light. LEDs can be difficult and I will probably need a relay to get them to work correctly. I'll just be happy to get to that point. ;D
 
Hey Big I think there is some pretty good conversation about LEDs somewhere on the board. Sorry can't remember where.

Tank is being stripped...again. I broke through the clear :'( LOL. Think I'm going to bondo in the badge mounts this time. Bike is out in the garage now but most of the tools are scattered in the living room.
 
troybilt said:
one more thing. My tag Lady called and informed me that I'm allowed only 6 characters on the vanity tags :( Here's what I'm thinking: TON UP or TONACE . You guys helped me build this bike so its only right to have you help me with the tags ;D So any more suggestions???

How about "ACE" on your plate?
my $.02
Troy
 
That clear looks awesome! I'm still going to go with the eastwood two-part clear. I have time to wait haha :)

As for the license Plate:
100bpm (100 babies per minute)

:D
 
Tank is stripped. I should be able to get some body work done on it tomorrow and paint/clear it on sunday.

Goodfor, I think the eastwood clear would be a great way to go. Wis it would have been in stock. It is a little pricey at $28 shipped but it would be well worth it for the extra durability. I can't believe how much harder the two stage is than the clear in the can.

Hey guys, thanks for all the ideas for the tags. I decided to go with 'TON UP' for now (my next two favorites are '100MPH' and 'ACE'). I have till Monday midmorning to add more choices or change it, so I'm still open to ideas.

I'm thinking of filling in the badgemounts on the tank. Do I need to remove the plate or can i just fill it in?
 
Troy your bike keeps looking better all the time. Really great job on the paint. Considering following your lead on the 2 part clear.
 
IMOALE said:
Troy your bike keeps looking better all the time. Really great job on the paint. Considering following your lead on the 2 part clear.
Thanks man, It was looking great until I got runs in the clear on the tank. Tried to sand them out and broke through the clear. Had to start all over. I'm still glad to have the two stage clear because it seems so much tougher than rattle can clear. You may think about the Eastman's clear that goodfornothing posted about earlier in this thread. I think it was going to be about $28 shipped but if it goes on like rattle can you can really knock it out. The sprayer that I bought sprays a little different than rattle can and I didn't like it near as much. Just my .02 worth. ;)


Well, since my tank is back to bare I plan to fill in the badge mounts. Can I just fill them in with bondo or do I need to remove the screw plates first? anyone??? Thanks, Troy
 
if you remove the plates you not only and end up with more space to fill but it'll leave holes where the plates were welded. Unless you carefully cut them out, but either way I don't see a reason to remove them. I bonded them without removal on my first tank, but i'm considering trying Quick Steel to fill 'em in on the one I'm doing now...
 
Back
Top Bottom