XS850 - Monoshock & USD Fork (pics pg 13)

Do yourself a really big favor and get Paul Thede's book on suspension tuning.

http://racetech.com/page/title/Suspension%20Bible

There is a LOT in there - probably way more than you want, but it is logically presented and easy to understand at what ever level suits you.

In the mean time, consider a couple of concepts before you determine to dive in to adjusting the hardware.

How any vehicle "handles" is greatly a function of the whole system, not just any one thing. It is hard to notice if the front is flawlessly dialed in if the back is out of whack. In fact it is pretty much irrelevant until the back also is good enough to enable you to notice either way. Mostly you will be better off with a whole system that is mediocre than one that is great on one end and awful on the other. So work toward getting an even balance.

The suspension is made of three components. One, the mechanical design - wheel diameter, tire size, swing arm length, wheelbase, rake trail etc, most of which is fixed. Two, the amount of motion and spring in that mechanical design, and three, the amount of damping applied to those springs. While these three things are obviously interlinked, it is extremely helpful to realize that you can consider, and therefore work on, all of them independently.

Since you can't change readily the mechanical stuff, you are left with just the springs and damping. Focus on the springs first, and after you get that right you can fool around with the damping.

When we ride our bikes, most of the times our attention is drawn to the suspension is when we hit bumps or pot-holes. This makes us look at the front and back independently as we hit these obstacles first with the front and then the back. I find it valuable to look at the whole bike at one time as a single system to avoid focusing on one area at the expense of another. So when working on the springs, you want to keep them even front and back. The rider is a massive component of the whole system so must be included and placed correctly when setting things up. XB's suggestion is a critical first step. Sit on the bike like you are driving it, and have someone balance you upright adding as little influence as possible. Have someone else measure how far the suspension is compressed. It should be the same percentage of travel front and rear. Next have someone shove down on your shoulders to simulate the extra loading the system will see in operation. The front and back should compress equally, and equally easily. You need to adjust spring rate and pre-load to achieve these conditions. Then you will have a very good starting point to getting a good handling machine. The damping adjustments come after, and even biasing the springs if desired, but having a balanced system to start with is the way to making logical decisions to achieve intentional changes. Bikes that are way too stiffly sprung, or way too weakly sprung generally handle way better than one that is stiff on one end and soft on the other. Balance! Once you have a good base to start from, the influence of tuning on the springs and damping will be much more obvious and easy to make decisions on.
 
This is great. Thanks for the input guys. My last few builds I just built up stock, for the most part, and didn't put a whole lot of thought into the suspension. On this one I definitely want to the best I can to dial it in for the most enjoyable ride, and best performance... with the parts I have of course. Maybe someday I'll get a better rear shock, but for now, I have what I have.
 
treitz said:
Whoa XB... You're speaking a foreign language to me. I understand how to adjust the rear shock, but twisting it so that the notches click up or down. Based on your lingo, the tighter it is the less sag you'd have?

On the forks, the attached image is what I'm dealing with. Based on where it's sitting, I don't even know where to start/how to adjust it.
well what you have there is either a compression or rebound adj clicker that is the screw..and if the green hex head, if that turns like a preload adjuster then it will feel like it ...def do some reading and as re-inner-rated buy the doc morbidelli the most imprtant thing is the even balance front to back garnerd from correct sprining ...the stock owners manual or fsm for the same bike will have a pretty good sin-optic on the deal of the actual adjustements available how-to
 
so the clickers control only damping orifice resistence to movement,wheel travel.. but they do not diktaite ride height .but do note the setting that was first riding impression, count clicks until seated to know where to restore each clicker ,write it down
the word suspension ,IE you and any of the motorcycle that is not part of any bits that move up and down with the wheels on bumps,are suspended by springs ,floating on springs, which in the act,alolne stores energy in the spring cause that is what springs are bilt for absorbing and storing energy, even if that energy is only imparted by gravity alone ,when so , this is static ,like hanging suspended motionless from a pair of springs, one front one back
 
I actually under stude that.

If you want to see is the front and back end working "together" jack the rear up and get the extended distance from the swing arm to a point (seat bolt mark on tail) then measure again on the ground for static sag... then get a friend to straddle the front to hold upright, add the rider and measure again to get "rider sag" deduct from full ext - static and rider sag... you are looking for a sweet spot around 25-35 mm diff for street and 25 percent less for race sag. repeat up front measuring from the dust seal to the axle mount. adjust preload to change sag 10-15mm max sag with rider in the seat for street and 25 percent less for race sag. If adjusting preload more than a few clicks you streach the forks and need to remeasure from the beginning.
 
jpmobius said:
Do yourself a really big favor and get Paul Thede's book on suspension tuning.

http://racetech.com/page/title/Suspension%20Bible

There is a LOT in there - probably way more than you want, but it is logically presented and easy to understand at what ever level suits you.

In the mean time, consider a couple of concepts before you determine to dive in to adjusting the hardware.

How any vehicle "handles" is greatly a function of the whole system, not just any one thing. It is hard to notice if the front is flawlessly dialed in if the back is out of whack. In fact it is pretty much irrelevant until the back also is good enough to enable you to notice either way. Mostly you will be better off with a whole system that is mediocre than one that is great on one end and awful on the other. So work toward getting an even balance.

The suspension is made of three components. One, the mechanical design - wheel diameter, tire size, swing arm length, wheelbase, rake trail etc, most of which is fixed. Two, the amount of motion and spring in that mechanical design, and three, the amount of damping applied to those springs. While these three things are obviously interlinked, it is extremely helpful to realize that you can consider, and therefore work on, all of them independently.

Since you can't change readily the mechanical stuff, you are left with just the springs and damping. Focus on the springs first, and after you get that right you can fool around with the damping.

When we ride our bikes, most of the times our attention is drawn to the suspension is when we hit bumps or pot-holes. This makes us look at the front and back independently as we hit these obstacles first with the front and then the back. I find it valuable to look at the whole bike at one time as a single system to avoid focusing on one area at the expense of another. So when working on the springs, you want to keep them even front and back. The rider is a massive component of the whole system so must be included and placed correctly when setting things up. XB's suggestion is a critical first step. Sit on the bike like you are driving it, and have someone balance you upright adding as little influence as possible. Have someone else measure how far the suspension is compressed. It should be the same percentage of travel front and rear. Next have someone shove down on your shoulders to simulate the extra loading the system will see in operation. The front and back should compress equally, and equally easily. You need to adjust spring rate and pre-load to achieve these conditions. Then you will have a very good starting point to getting a good handling machine. The damping adjustments come after, and even biasing the springs if desired, but having a balanced system to start with is the way to making logical decisions to achieve intentional changes. Bikes that are way too stiffly sprung, or way too weakly sprung generally handle way better than one that is stiff on one end and soft on the other. Balance! Once you have a good base to start from, the influence of tuning on the springs and damping will be much more obvious and easy to make decisions on.
I have this book myself...LOTS of nfo...very good stuff
 
Appreciate all of the suspension input. Still ironing out some tuning bugs.

Question... what does stinky smoke from the breather mean? I had the same issue on the last 850 I built. When it get's warm it just starts smoking out of the breather filter at idle. Thoughts?
 
treitz said:
Appreciate all of the suspension input. Still ironing out some tuning bugs.

Question... what does stinky smoke from the breather mean? I had the same issue on the last 850 I built. When it get's warm it just starts smoking out of the breather filter at idle. Thoughts?

Its oil vapor/steam.
I think its normal unless its starts chimneying out real bad. Does it stop when you rev it you mean?
I'm by no means an expert but with tired piston rings some compression goes out the crankcase and out the breather.
It stopped smoking on my gf's xs11 when we bored it out and fit fresh pistons.
Well its still smoking slightly but much less. My newly rebuilt engine also steams out of that hole, but when its connected to an airbox you dont see it, its just greasing the carbs! :)
Hook up a catch can if it bothers you!
 
datadavid said:
Its oil vapor/steam.
I think its normal unless its starts chimneying out real bad. Does it stop when you rev it you mean?
I'm by no means an expert but with tired piston rings some compression goes out the crankcase and out the breather.
It stopped smoking on my gf's xs11 when we bored it out and fit fresh pistons.
Well its still smoking slightly but much less. My newly rebuilt engine also steams out of that hole, but when its connected to an airbox you dont see it, its just greasing the carbs! :)
Hook up a catch can if it bothers you!

Ha this is what I assumed. Yeah, it stops when riding/revving. I just wanted to make sure it wasn't something I should worry about. Funny that you would want that crap flowing back through your carbs with a stock airbox... but I guess it couldn't do any harm.
 
The tuning saga continues. Man. This thing is stumping me. I was hitting some weird hesitations/popping on the right side at low-mid throttle, so I pulled the carbs AGAIN to double check everything. Shot more air and carb cleaner through EVERY hole in the carbs. All clear. Put it back together and idled great, did a carb sync yesterday, and it's doing the EXACT same thing today.

The sound is definitely coming from the right side which is the middle pipe and right pipe. So it could be either cylinder. It almost sounds like the cylinder is skipping a fire at low-mid throttle. I don't know. Hard to explain because it's sort of a new phenomenon for me.
 
frustrating sucks man,just remember you must make sure everything about the ignition is 100% before chasing a problem that you think is carbs
 
xb33bsa said:
frustrating sucks man,just remember you must make sure everything about the ignition is 100% before chasing a problem that you think is carbs

Spark is good, and timing isn't adjustable... so what else am I missing?
 
One long shot is microscopic intermittent shorts in the signal wires from the pickups.
Even though they are high quality silicone clad wires they're over 30 yrs old and cracks are more likely than no cracks! :)
Still a long shot but checking is free!
They always break where they come out of the cover.
 
I checked them when I had the side cover off to check the valves and they looked solid. What elements, other than the coils and CDI are involved in the ignition sequence?

I guess new spark plug wires and caps couldn't hurt. But like I said, spark looked solid.
 
If plug wires and caps are old they should probably be changed anyhow.
Dont think there's anymore to the ignition than that, really simple system thankfully!
 
Also remember, I swapped the coil from 1 to 3 previously to see if it was causing any issues, and nothing changed. So I guess based on that, the coil/wire/plug cap can be ruled out.
 
MotorbikeBruno said:
Bummer. Do the plugs all look the same now at least?

I'm going to check again tonight. As of the end of last week, the left plug was still looking pretty black, and not super consistent across the board which is why I decided to go through the carbs ONE more time. We'll see how they look after riding it today.
 
Back
Top Bottom