XS850 - Monoshock & USD Fork (pics pg 13)

A running video after work. Engine fully warm. Interesting facts...

1) It runs better when warm
2) it only has an issue with load. So you can't really hear it in the video
3) I THINK it's still rich. But I can't figure out how/why with open exhaust, open intake, and stock jets. UNLESS the jets aren't actually stock.

Checking plugs later...

https://vimeo.com/136566563


Sent from my iPhone using Tapatalk
 
1 still black. 2 and 3 pictured. 2 rich, 3 okay??

I'm stumped!

8c6e8a051e951060dc1a320335ea95ba.jpg


707668c6ccf95946d48306299f6517d5.jpg



Sent from my iPhone using Tapatalk
 
If it runs better warm that would indicate leanness.. so weird.
Engines are generally harder to tune with cylinders running independent for anything but wot,
Things like back pulses and poor exhaust scavenging can mess things up worse than one may think.
On the other hand joint intake and exhaust can mask poorly running cylinders.
Do you switch plugs or do you read the same old ones over and over?
Maybe you need to verify the main sizes, people drill these out and make all sorts of mess.
Previous owners are a pain in the ass..
 
datadavid said:
If it runs better warm that would indicate leanness.. so weird.
Engines are generally harder to tune with cylinders running independent for anything but wot,
Things like back pulses and poor exhaust scavenging can mess things up worse than one may think.
On the other hand joint intake and exhaust can mask poorly running cylinders.
Do you switch plugs or do you read the same old ones over and over?
Maybe you need to verify the main sizes, people drill these out and make all sorts of mess.
Previous owners are a pain in the ass..

Yep, I'm going with this too ^ we HAVE to verify the jet sizes. Even if that means buying new ones... There's got to be something odd going on in the first cylinder, the second is still rich, and the 3rd is just about ok. I'd maybe have it a slight bit more on the rich side. For things like this that stump me....I go to my colortune. Don't forget to get the proper size (12mm or 14mm) I have all 3 sizes due to the amount of bikes I work on, but nowadays I rarely pull the colortune out :) I can't remember where you are located, but if you want me to send it to you if you cover the postage I'd be OK with that. It lets you see inside the cylinder and what your changes will actually be doing. I liked it for A/F ratio help when I was building my own bikes. You could look in the cylinder and tell right away if you were far too rich or lean. With new plugs, the interesting thing you may find is that your A/F at idle is OK but when you give it throttle you get far too much fuel. You find that with slide needles set way too Rich but you can adjust the mixture screws on the low end to make it idle well :) haha Anyways, something to look into since you can watch changes in real time.

http://www.ebay.com/itm/like/181789915571?ul_noapp=true&chn=ps&lpid=82
 
have we ruled out leaking isolators yet? spray a bit of starting fluid or carb cleaner at the boots connecting the carbs to the engine while it's running. #3 plug looks good. only other thing I can think of is sync or that the jets were drilled out messily and aren't identical is size. can always swap the main and pilot jets around to other carbs and clean the plugs and see if the richness follows the jets....
 
Bruno, I do not have a colortune. Looks like a handy tool! I'm am located a hour east of Portland Oregon - Hood River Oregon.

Some thoughts...

1) Early on in the tuning process I bumped the needles UP a clip to richen the system. Might be worth dropping it back down to see what happens?

2) Like a week ago, maybe the 3rd or 4th time I pulled the carbs, I did swap jets around between carbs and it didn't make a difference at all.

3) A leak at the carb boot would cause lean symptons, not rich. So that might answer #3, but not so much #2 or #1.

I guess my biggest confusion comes from the difference between the cylinders, even after a carb sync. I can adjust the air screws to get it to run better, but none of them will be the same. Doesn't seam like a good long term solution.
 
Well, they don't all "have" to be the same on the mixture screws. It's one reason they are there. You can adjust mixture to each cylinder's needs. Now generally they are about the same. So there's still something funky going on. Maybe you have the 2 left cylinders rich and the third has an air leak like you said. So you've been trying to tune to the 3rd one, when realistically it's the problem child. :-\
 
treitz said:
Totally possible... although the intake boots ARE brand new.

Hmmm...then from somewhere else....haha I'm voting carbs. Shoot them on over to me, I'll put them through the ultrasonic cleaner :)
 
MotorbikeBruno said:
Hmmm...then from somewhere else....haha I'm voting carbs. Shoot them on over to me, I'll put them through the ultrasonic cleaner :)

Haha... where are you located!?
 
I bought a cheap ultrasonic a little over two years ago and haven't done a set of carbs without it since. eliminates all the guess work on whether or not the internal passages have been cleared. Mine is small, so it also FORCES me to break every rack down to individual carbs which then often helps me out because I discover issues I may not have if I left the rack together and had a larger ultrasonic cleaner....
 
focusinprogress said:
I bought a cheap ultrasonic a little over two years ago and haven't done a set of carbs without it since. eliminates all the guess work on whether or not the internal passages have been cleared. Mine is small, so it also FORCES me to break every rack down to individual carbs which then often helps me out because I discover issues I may not have if I left the rack together and had a larger ultrasonic cleaner....

Meh, I find that realistically only a small handful of carbs need to be split and pulled apart. Yes a bike that has sat since the 70's, 80's and 90's will most likely need that. Buf if the carbs have been gone through at least once in the last 10 years, usually it's not the case. I think I've got well over 150 sets of carbs through this beast, realistically I don't even have to pull the carbs apart at all and it does some great work on them. I get several sets that have stuck slides where the main jet is varnished in so badly that you CAN'T take them apart first without damaging something or prying up on the slide which is not a joy for it or me. Plus, I leak test after I clean by hand (after the ultrasonic to make damn sure they are clean, as nothing replaces a good hand cleaning)

Don't get me wrong on the above statements, it's definitely BEST to do what you do focusinprogress. On my personal bikes, I usually end up doing at least the fuel rail o-rings and such, but the average person doesn't want to spend the money on the time it takes to do them right and if they aren't leaking...well...they are working. :) Plus, I can get a whole rack of GL1000 carbs in here no problem!
 

Attachments

  • sharpertek.jpg
    sharpertek.jpg
    229.9 KB · Views: 352
focusinprogress said:
I wish I could bring myself to buy that nice of a cleaner Bruno lol.

Well, I only did it because it would pay for itself over time. If you clean 100+ sets a year, this thing is a time/life/carb saver!
 
That's a lot of carbs gentlemen... Damn.

So I adjusted the air screws independently just see what I could find. I got #1 to lean out and stop making the plug black. Might have gone too far. I get a little popping on decel now.

Having a harder time actually getting #3 to richen out. The air screw is almost completely removed and it's still acting a little lean. I'll check plugs again tonight.

Again, baffled by the inconsistency here. If they were all lean, or all rich, things would make a lot more sense.
 
In an effort to help out the best I can, I re-read the ENTIRE thread.....


a previous reply from you:
Responses below...

Verify float needle is the same as the others. Aftermarkets mess with float heights etc. - All 3 float needs are band new.
Check that float needle spring is in good working order and compresses and extends out properly. - Brand new, so shouldn't be an issue.
Float height (you know it's good/near the others, but check again) - Literally JUST checked it like 2 nights ago with a fuel hose connected to the carb.
Main jet? Verify by setting near other mains just in case it's been drilled out for some dumb reason? - Not verified...
Main jet holder in correctly? - Checked when I had the needs pulled the other night. Looked good.
Missing washer for pilot jet cover? - Added these in the other night also.
Pilot jet not drilled out (possible like main jet) - Not verified
Slide needles all the same (I think you just checked this) - Verified

Lastly: The choke circuit. That's the only other thing I can think of. Something is botched in the choke circuit, either not closing fully, or the plunger is stuck or missing? Who knows!? - Checked when I had the caps off, looked ok.

So based on the 2 unverifieds being the main and pilot jet... I wonder if it's worth swapping the main AND pilot from #1 into #2 and seeing if suddenly #2 is rich instead of #1!? Not sure how else I could be sure if it's the jets.

very early on it was brought up that there's a lot of corrosion present in the carbs and their usability in question. based on pics that's quite possibly the truth....but your time is "free" so there's no sense throwing these in the bin until you've verified 100% they won't work right.....so let's get to that.

you mentioned previously, your cleaning method was a pine-sol boil. Were the carbs still as a rack for this, or broken down to complete individual bodies?

originally, you had #1 rich, 2,3 lean (in comparison to each other)

Later, you sealed a crack in the pilot pickup tube. There was mention of missing copper washers....did you install these?

Then you removed an air corrector that appeared to be clogged in #1, and now that carb is running better, but now #1,#2 are rich and #3 is lean (in comparison)

then this:

Remember that plugged air jet? Well, I pulled it out and shot carb fluid into the opening and it just shot back in my face. Tried the same thing on carb 2 and it flowed through the carb and out the tiny hole on the back side (engine side) of the carb. Pulled the air screw out of carb 1 and sprayed fluid in and it flowed through the tiny hole (as it should). Conclusion, there is a plug on the pilot air circuit someone between the air screw and the air jet. If this is true, then I would be getting 100% gas at idle with little to no air at all to lean it out.

Plan is to shoot some compressed air through from the air screw opening and see if I can blast the plug out.

Did you do the same test on #3 for consistency of the test?

Carbs are like fractions....the old adage "what you do to the numerator you do to the denominator" applies....do the same to all of the carbs. always.

I mentioned a page back leaking isolators could be the cause....you said they are new....I'd still spray something around them to see if idle changes, indicating an air leak. Lots of times old isolators are dried up and hard...and too small....while new ones are nice and pliable, I find often they are almost too large and require better than stock clamps to get them sealed down.

Another question I did not see asked....is have you examined the slide diaphragms for pinholes? I've run into it multiple times on these MKII's and get my replacements from JBM industries and have had great results.

Also, you said your bike CAME with the MKII's.....which run lean on a stock 850 with stock jets from the 750 these carbs were from....so it's likely they've been drilled out, esp if you're seeing rich conditions with open 3-3 exhaust and UNI pods.

as for you're rebuild, I know you said the float valves are new.... the aftermarket ones are not as good as OEM, and may vary enough that identical float height across the three carbs may not be ideal. try lowering the float height on the problem carb 1mm and see if it improves. Of course only do this after verifying the diaphragms are good, and that all of the passages are indeed clear and flow the same (like I mentioned earlier your spray tests in 1&2 but no mention of checking #3).

Lastly, at this point I think the best course of action is to re-clean these. take out every possible piece from them....all the air correctors in the mouth of the carbs, all the choke plungers, all the jets, etc. and go nuts with carb clean and compressed air through every passage you can. if the same passage on each carb doesn't kick out similar amounts of cleaner then you know you have to keep blasting until it's the same. also, be sure to hold your pilot jets up towards a light source and verify you can see the same amount of light through them. I bought a nice set of jet cleaner wires on ebay for like $14 that are sized per jet orifice to poke through and make sure there's nothing stuck in there the eye can't see, I don't ever install a used pilot without running a wire through now. if gas has ran through it, I poke it.

anyways, I hope this all helps. Really kills me to see after all the work you're having so much trouble with it mechanically with the brakes and carbs.
 
Found a guy in Portland with an ultrasonic cleaner. Going to drop them off this weekend to have them done. Will be interested in the results!

Answers listed below. Thanks for the thorough post!

focusinprogress said:
"you mentioned previously, your cleaning method was a pine-sol boil. Were the carbs still as a rack for this, or broken down to complete individual bodies?"

- They were broken down to individual carb bodies - everything removed

focusinprogress said:
Later, you sealed a crack in the pilot pickup tube. There was mention of missing copper washers....did you install these?

- I don't recall if I mentioned, but the crack in the pilot tube was actually in carb #3, not #1. So I ruled it out as an issue as #3 is lean, not rich. Copper washer WERE added.

focusinprogress said:
Did you do the same test on #3 for consistency of the test?

- Yes, all 3 have had air blasted through every opening imaginable

focusinprogress said:
I mentioned a page back leaking isolators could be the cause....you said they are new....I'd still spray something around them to see if idle changes, indicating an air leak.

- Worth checking!

focusinprogress said:
...have you examined the slide diaphragms for pinholes?

- Is there a special method for testing this? I've checked them over, but I'm not sure how you would identify a "pinhole"

focusinprogress said:
Also, you said your bike CAME with the MKII's.....which run lean on a stock 850 with stock jets from the 750 these carbs were from....so it's likely they've been drilled out, esp if you're seeing rich conditions with open 3-3 exhaust and UNI pods.

- This is a very valid point. Getting my hands on some stock jets would be a good idea.
 
Yep lots of great info and re-checking there.

As for the pinholes. You are looking for any holes in the diaphragms. Pin holes can cause problems, but usually you'll find a rip/tear versus a pinhole. Best way is to hold it up to a light and slowly tug on the rubber giving it a slight stretch SLIGHT. So rotate and look for any spots light comes through is really all you are doing. The light behind just makes it easy if there is a pinhole due to their small size of course.
 
Back
Top Bottom