In an effort to help out the best I can, I re-read the ENTIRE thread.....
a previous reply from you:
Responses below...
Verify float needle is the same as the others. Aftermarkets mess with float heights etc. - All 3 float needs are band new.
Check that float needle spring is in good working order and compresses and extends out properly. - Brand new, so shouldn't be an issue.
Float height (you know it's good/near the others, but check again) - Literally JUST checked it like 2 nights ago with a fuel hose connected to the carb.
Main jet? Verify by setting near other mains just in case it's been drilled out for some dumb reason? - Not verified...
Main jet holder in correctly? - Checked when I had the needs pulled the other night. Looked good.
Missing washer for pilot jet cover? - Added these in the other night also.
Pilot jet not drilled out (possible like main jet) - Not verified
Slide needles all the same (I think you just checked this) - Verified
Lastly: The choke circuit. That's the only other thing I can think of. Something is botched in the choke circuit, either not closing fully, or the plunger is stuck or missing? Who knows!? - Checked when I had the caps off, looked ok.
So based on the 2 unverifieds being the main and pilot jet... I wonder if it's worth swapping the main AND pilot from #1 into #2 and seeing if suddenly #2 is rich instead of #1!? Not sure how else I could be sure if it's the jets.
very early on it was brought up that there's a lot of corrosion present in the carbs and their usability in question. based on pics that's quite possibly the truth....but your time is "free" so there's no sense throwing these in the bin until you've verified 100% they won't work right.....so let's get to that.
you mentioned previously, your cleaning method was a pine-sol boil. Were the carbs still as a rack for this, or broken down to complete individual bodies?
originally, you had #1 rich, 2,3 lean (in comparison to each other)
Later, you sealed a crack in the pilot pickup tube. There was mention of missing copper washers....did you install these?
Then you removed an air corrector that appeared to be clogged in #1, and now that carb is running better, but now #1,#2 are rich and #3 is lean (in comparison)
then this:
Remember that plugged air jet? Well, I pulled it out and shot carb fluid into the opening and it just shot back in my face. Tried the same thing on carb 2 and it flowed through the carb and out the tiny hole on the back side (engine side) of the carb. Pulled the air screw out of carb 1 and sprayed fluid in and it flowed through the tiny hole (as it should). Conclusion, there is a plug on the pilot air circuit someone between the air screw and the air jet. If this is true, then I would be getting 100% gas at idle with little to no air at all to lean it out.
Plan is to shoot some compressed air through from the air screw opening and see if I can blast the plug out.
Did you do the same test on #3 for consistency of the test?
Carbs are like fractions....the old adage "what you do to the numerator you do to the denominator" applies....do the same to all of the carbs. always.
I mentioned a page back leaking isolators could be the cause....you said they are new....I'd still spray something around them to see if idle changes, indicating an air leak. Lots of times old isolators are dried up and hard...and too small....while new ones are nice and pliable, I find often they are almost too large and require better than stock clamps to get them sealed down.
Another question I did not see asked....is have you examined the slide diaphragms for pinholes? I've run into it multiple times on these MKII's and get my replacements from JBM industries and have had great results.
Also, you said your bike CAME with the MKII's.....which run lean on a stock 850 with stock jets from the 750 these carbs were from....so it's likely they've been drilled out, esp if you're seeing rich conditions with open 3-3 exhaust and UNI pods.
as for you're rebuild, I know you said the float valves are new.... the aftermarket ones are not as good as OEM, and may vary enough that identical float height across the three carbs may not be ideal. try lowering the float height on the problem carb 1mm and see if it improves. Of course only do this after verifying the diaphragms are good, and that all of the passages are indeed clear and flow the same (like I mentioned earlier your spray tests in 1&2 but no mention of checking #3).
Lastly, at this point I think the best course of action is to re-clean these. take out every possible piece from them....all the air correctors in the mouth of the carbs, all the choke plungers, all the jets, etc. and go nuts with carb clean and compressed air through every passage you can. if the same passage on each carb doesn't kick out similar amounts of cleaner then you know you have to keep blasting until it's the same. also, be sure to hold your pilot jets up towards a light source and verify you can see the same amount of light through them. I bought a nice set of jet cleaner wires on ebay for like $14 that are sized per jet orifice to poke through and make sure there's nothing stuck in there the eye can't see, I don't ever install a used pilot without running a wire through now. if gas has ran through it, I poke it.
anyways, I hope this all helps. Really kills me to see after all the work you're having so much trouble with it mechanically with the brakes and carbs.