Search results

The CB750 project has been put on the back burner while wedding plans are sorted. I need to free up some cash and this tank needs to go. It is the alloy Manx TT tank from legendary-motorcycles.com and comes with the Monza cap. It is finished in the brushed/mill finish and is pretty much a...

Bought these when I was doing a cb350f project, and no longer have a need for them. They were purchased from Kevin at TTR400.com and they are NLA. They are machined aluminum, and anodized black. Works on 33mm forks only. 2 piece design allows easy install on fork tubes. $100 shipped in the...

I was going to use the GL1000 front end for dual discs, but have decided to go with USD forks on the front. The forks are in good condition, with no leaks and function fine. The wheel comes with the discs, axle, and spacers. Only part needed is the speedo drive to complete the front end...

Just finished up this project, and thought I'd share. I found it up in Michigan on ebaymotors.com. It has a clean title, and when I took delivery of it, ran and drove. Being from MI, it had some rust on the frame, and wheels. The tank had a considerable amount of rust inside, but was solid...

Parting out my 73 xs650 bobber project as I don't have the time to finish it with my other projects. Below is a list of parts I am selling. - 18x2.15 alloy wheel laced to rear hub with stainless spokes: $150 - 19x1.85 alloy wheel laced to front hub with stainless spokes: $150 - lowbrow peanut...

Hey guys, I have decided to use the stock 19" on the front of my xs650 bobber, so the 21" alloy wheel and stainless spokes are up for sale. The spoke kit is from Mikesxs, and the wheel is a Borrani replica. It is 1.60 in width (WM0). The nipples on the spoke kit are a touch bigger than the holes...

Bought this when I had a cb450. Sold the bike, and this has been sitting in the original packaging. Unit was never installed on the bike. Paid $119+shipping, selling for 95 shipped to the lower 48. I accept paypal as well. Thanks Jared

Hey guys, I have a 1974 CB450 bike i am parting out. It does not have a title. The engine spins with good compression, and it is a complete bike. Just don't have time to restore it, and need to make room. Please post here, or email me at jsedacca@gmail.com with any questions, or parts...

Hey guys, I decided to make my own seat so it fit the frame, and rear hoop how I wanted. I have done some fiberglassing in the past, but nothing to this scale. It was a pretty easy process. The toughest part was getting the seat shaped to the contour I felt fit the lines of the bike...

Bought these on here last month, and the project is at a stand still, so they are for sale. They have only had gas run through them to sync. This is pretty much a bolt on kit. Includes - 2 carbs - 2-1 throttle cable - uni-filter pods - CB360 rubber carb holder 270 shipped takes the kit.

Hey guys, This was going to be for the girlfriend, but you know how that goes. I need to sell it asap as I am moving, and just want it gone. Here are the specs/details on the bike: -1975 cb200T with 9104 miles -tank was repainted lexus pearl white and has joker side emblems -wheels were...

No longer plan on using these and they are taking up space under my workbench. They are both 18" 36hole rims. One is 1.85 (WM2) and the other is 2.15 (WM3). Perfect for a front/rear combination. The WM3 wheel is from xsperformance and is in perfect shape. It has never been used or laced to...

Just removed this from the bike as I'm switching to PWK flatslides. The throttle cable is not included. What you see is what you get (carb, 2-1 manifold, rubber manifold, and the hardware to mount the adapter) The rubber manifold needs to be replaced as it has some dry rot to it. $200 shipped...

Just recently acquired this beauty and plan on restoring it to showroom condition. It is a MKIII which has the electric starter. It starts up and rides fine. The previous owner replaced the dual Amals with a single Mikuni VM34, and fitted a Boyer electronic ignition. The only part that has...

I'm parting out my entire CB400F project and need these parts gone. All prices do not include shipping unless specified otherwise. Shipping will be combined if more than 1 part is purchased. I have many more parts so if you don't see it, feel free to ask. Here is the preliminary list: -...

I'm looking for a known/recommended machine shop to bore/hone the cylinders on my cb350f and cleanup/deck the cylinder head. Any help would be appreciated. I dont care if the place is in Pinellas, Hillsborough or Pasco county. Thanks guys

I have this xt500 tank leftover that needs to go. It has been blasted and the inside cleaned out. The only imperfection is the dent on the left side. Does not come with petcock. Gas cap is included. 40+shipping takes it. Thanks

The motor has seized on my xt500 cafe and just need to part it out. Bought a new triumph bonneville t100 yesterday so have no use for anything. All prices are best offer. Shipping to the lower 48 is no problem. Shipping to Canada will cost a bit more. Here is the list: 1) Borrani aluminum...

Just picked up cb200 for the girlfriend and the only problem on the bike is first gear. I changed the oil/adjusted the clutch and she fires right up. While on the center stand, I can put it into first gear and completely release the clutch with no issues/noises. When the bike is on the ground...

Bought this from motolanna who specializes in SR500 parts. It fit great on my xt500 but after switching to a longer manx style tank, it does not fit. It consists of a fiberglass base and is covered in naugahyde with nice pleats and red stitching around the borders. It could be a universal seat...