Search results

Hey all, Just got ahold of a 78 CB750k for $175 (with title). Needless to say, I'm pretty stoked about the price. Cleaned it up, did a shit load of odds and ends work, and then fired her right up, third kick. Rear brake was seized up, got it free and cleaned, lubed. Front brake is shot, master...

Hey all, I am just getting my project bike on the road a bit. I've been fixing problems as they crop up but I'm looking for some feedback on on issue I'm seeing. When I start the bike, it idles fine after firing off a single kick. Every time. Then when I pull the throttle up to take off the...

Hey all, I was riding just the other day, on only the third or fourth ride of my new build, when suddenly she bogged out and refused to rev at 55 in 6th gear. She ran right down to nearly nothing and sputter and putted along at what was nothing more than a coughing idle in first. Initially I...

Hey, just looking for confirmation here... I've got a coil that's causing my main circuit to blow (yes I'm sure it's the coil). Upon testing, I have wildly varying resistances and continuity between all leads which changes every time I shake the coil. I am assuming it's a fair guess to say the...

Alright, I am working on a '75 Honda CB 360. I ordered this half turn throttle assy from Dime City and the threads for the throttle cable are non-stock...

Let's get right to it... 1) What gauge wire should I run to the primary winding of the coils with a 4.2 Ohm resistance? - At 4.2 Ohms on the primary windings and 12V that's 3.07 Amps... according to http://www.solar-wind.co.uk/cable-sizing-DC-cables.html (allowing for 1m of cable) that...

Hey all, I'm trying to get an amperage draw reading on my turn signal light. I have it wired straight to the battery for testing (not through the relay) so that I don't have to try to read the amperage between flashes. My ammeter is wired in series with the turn signal. It starts somewhere...

Hey all, I'm looking for a rotor setting bolt for my 75 Honda CB360. Does anyone have an extra or know if there is an equivalent bolt I can get off a different year/model? The Rotor Setting Bolt attaches the rotor to the crank shaft. The head of the bolt on my original snapped clean off...

So, in the process of torquing down the rotor to spec (23lbs) the rotor setting bolt on my 360 decided to snap mid shaft. I've removed the broken bolt and am now in the process of finding a replacement. Can anyone confirm other CB models that have the same rotor setting bolt? Or suggest where...

If I wire this in to my 360, do I wire white yellow from alt to single yellow on R/R, and pink to yellow? Or each alt wire to an individual yellow on the R/R? Also what do I do with the black? Does that take a 12V hot lead? Or do I not wire it in? Thanks.

Hey all, I'm wiring my CB360 back together right now and have decided to wire in the old regulator/rectifier (I know you're all going to want to tell me to buy a new one). It would be extremely helpful if someone could clarify a question I've got going on right now. Attached is a wiring diagram...

Hey all, How many #8 ball bearings are supposed to go in each side of the steering stem? Also, where would be a good place to purchase new ball bearings? #8 ball bearings (as stated in the manual) don't seem to turn up many results...

Hey all, I've just finished a lot of my parts with their paint coats, pretty exciting! I put my float bowls back on (now painted black) and as I torqued down one of the allen heads (not over-torqued) the first thing that happened was a nice flake of new paint chipped off around the bolt. As I...

Alright, I need to get to the starter clutch to remove it (getting rid of the electric start) on my CB360. Will any 16mm flywheel puller do the job? The one here from Bike Bandit is nice and cheap and my understanding is that the magneto (behind which sits the starter clutch) is removed with a...

Going kick only. Pulled the starter, starter sprocket, and chain. Do I need to remove the other sprocket or am I done here? See picture.

What is this central piece on the lower triple tree? Was it at some point a fork lock? Can I cut it off?

Hey all, I'm trying decide to save or cut these last two tabs. Can someone identify them and advise as to cut or save? First one is right under the steering tube up front. The other ones (symmetrical) are below the seat and in front of the old battery box.

Hey all, I'm looking to make my own set of clip on bars, but I need the bracket that mounts the bars to the fork tube (it would be a lot easier to pick a pair up cheap than to make them). Any chance there is a set of 33mm clip on brackets out there with or without the bars included?

Which side makes contact with the brake pad? The side with a small bevel in the center (oem) or the side with the recessed lip around the perimeter? I have the original piston on the left in the photos and a replacement piston I ordered on the right. The new one is making clearance issues with...

Hey guys, just got ahold of my '75 CB360 a couple days ago. A year ago the cam tensioner snapped, the cam skipped two teeth, and the timing was off so badly it melted the end of the exhaust on one side. My buddy (who I got the bike from) completely rebuilt the engine after that happened and is...