Search results

Edit: No longer needed I need a gas cap for a kawasaki AR80 I'm working on. The Kawasaki part number is 51048-1001. The same part came on the following models: 1978 KZ400-B1 1978 KZ400-C1 1978 KZ650-D1 1978 KZ650-D1A 1979 KZ400-B2 1979 KZ650-D2 1980 KZ440-B1 1980 KZ650-E1 1981 KZ440-B2 1982...

Is that an extra pipe in the second picture? I'm looking for a new pipe for my G3SS because mine has a big hole in it from the kick start lever.

This was really really helpful. I shortened the driving arm as it was easier than adding material onto the driven arm. I seem to have it set up so that I can shift with about the same force (or a little less) as a stock shifter now, but I also seem to have a lot of travel in the lever. I think I...

Rochester ny.

I wish you were closer. I have a spare R5 motor in my garage. I would trade you for the busted one. It would be a shame to drop a 4t lump in that beast.

So I drilled a hole on the shift lever closer to my foot peg. It seems to shift a lot easier now, but the travel on the lever is really far. Argh! Ever since I got run over by a car on my rd350, I don't have a lot of strength in my foot and I don't have the range of motion I did before. Somehow...

For the price of a set of cases on ebay ($240 OUCH!) I would probably either take them to a reputable welder and have him weld up your cases. Make sure everything is disassembled and very clean. I'm sure you could probably find someone to weld that up for $50-$100 (way cheaper than any other...

So I've been wanting to put rear-sets on my R5 project for a while. I finally picked up a set of Yoshimura aluminum rear-sets for $47 shipped on ebay. The brake side mounted up extremely easily once I bent the kick starter out of the way. The brake side seems to work really well. The issue...

I just bought a set of DG chambers from denniskirk.com for $269 shipped. That was the cheapest I could find them. I believe they sell them on ebay for the same price. Carbs are a no brainer. you can upgrade to KOSO PWK style carbs that flow better and provide superior throttle response for the...

I should be all set on pistons. The ones in there look brand new when I look through the ports. Knowing the previous owner, it's probably missing rings though ::) He stripped everything important off it and sold it to me as a "complete barn find" what a joke... anyway, back on topic. I may have...

I e owned a few rd350s and an R5 in the past, so I have an idea about the interchangeability of most of the rd and ds7 parts with the r5. You can run an RD air box in the R5. The rd just has a rubber boot on the bottom of the box. The RD lid is a bit different, but could be modified to make it...

Redbird: I PMed you. I think I have a battery bracket. I'm upgrading the carbs, so the air box won't fit after all. looking for a tail light lens to go with Redbird's bracket or the whole assembly if someone has it. I really really need a set of fenders though.

I'm in the market for a few parts for a newly acquired bike of mine, a 1971 Yamaha R5B. I'm looking for a few parts that are usually taken off on cafe builds so maybe I'll get lucky. I need: front fender rear fender tail light (with bracket) air box with filter, lid, and rubber boots battery...

I shot you a PM

I'm starting a couple new projects and it seems like everything I come across needs forks. I'm looking for a set for forks for my R5 and my air cooled RD250. I really only need the stanchions, but will happily buy the whole fork setup if you have it. Let me know what you have. Thanks, Eric

I'm looking for a set of suzuki t350 cylinders and pistons for my '71 t350. I definitely need the left one, but both would be even better. I'm hoping to get late model ones (the ones with the aux exhaust ports), but I'm not picky and will take whatever as long as I can get my bike back on the...

I've had this set of rearsets sitting on a shelf in my garage for a few years and never got around to putting them on a bike. They're billet aluminum and have roller bearings in them. Unfortunately, I need a set of cylinders for my '71 Suzuki T350, so I'm looking to trade the rearsets and a bit...

Re: '75 suzuki gt250 Ever think of going to reeds? Now that I have a gila monster, I believe I need to try polini-izing a larger bike. Maybe I'll give it a shot on my t500 when I tear it down for a rebuild. Something like this...Thoughts?

Re: 72' Suzuki GT380 first time build (She Lives!!!) If you're having a hard time finding brake shoes and brake cables, I have some off my bike that you can have for shipping. They are used, but they would at least get you through until you can find some new ones. It has to be better than no...

I have a few mopeds, but I don't have a batavus. Are you interested in any other brands? I have a 2 speed solo cafe that needs a new home... 8)