Search results

Thank you. I will let him know what I have found out and hopefully he can get it sorted out.

Thank you. My father has been working on it, I've been staying home as I am worried about my parents getting sick. He says he has it wired the way you mentioned. He says everything from that switch is wired to the bike at the moment. Are you saying that something needs to be unplugged from...

Hello! Think I am in the final stages of my project 73 CL350... I am using the Honda switches sold by Cognito Moto (yes, I have asked them for input on the issue I'm having). Everything seems to be wired correctly except the kill switch - the bike starts regardless of the position of the...

thank you! Just need to figure out what to do about the seat now

Hello all, Wanted to share my project. It's the first bike I have ever worked on and it has been a huge learning experience. I believe I am finally about done with it and very excited!

I can take a picture this evening. As far as I can tell the only thing holding the swing arm on would be the bolt through the frame and arm and the shocks

They are the brackets that have the passenger foot pegs mounted to them. The swing arm bolt does go through them, but its hard to tell if they actually serve a purpose to the swing arm.

Hello again! I am looking for more information about the use of the passenger peg brackets on my CL350. I removed the brackets themselves for aesthetic reasons, but I am questioning if they serve a purpose to the swing arm? Is it safe to run without them? Thank you

Does anyone have a trick for filling this gap or other options between the stock fork boot and the tube? I removed the stock headlight brackets.

Found a crack in the triple tree on my 73 cl350! Found it while removing forks. I have a 72 that I can take the top clamp off of, but can’t seem to find an answer as to whether or not they can be swapped. They only look slightly different. I see a lot of billet and aluminum ones on cognito...

I am exploring options for seats and am leaning toward tuffside seats. I purchased a cafe seat from Amazon, but it was just a cheaper option. I realized after some more research my cheaper option is roughly 4 inches shorter than the tuffside seats, which kind of sucks being that it wouldn't be...

Thank you everyone for the advice and input! I will keep going with what I have for now and make adjustments if necessary... do kind of wish I just went with clip ons, but I can always change that later. The other concern I had aside from cable lengths was the ends of handlebars when the forks...

I will check, I think I may have run the throttle cable up the right side... if not, then I need a shorter throttle cable. Common Motor only has one size though

I'm not sure if I felt uncomfortable when I sat on the bike and tried them... but I'm also short at 5'7... I felt more like I was doing a stretch and I was speed racer. I'll have to try them again and maybe I'll pick up clip-ons. I am concerned about the clutch cable I got now though, it's the...

I considered clip ons but I wasn’t sure about them or what the pros/cons were... I thought they’d sit much lower than the clubman bars?

Okay haha, I wasn’t sure if there was a best way to have them. I have no room at all to move anything on the right side. I did notice that the throttle cable is way to long now, I’m going to have to have to try and shove some of it under the tank I assume...? Don’t have a new brake cable...

Thanks! I ordered your regulator last Thursday

Tried putting new handle bars on my bike tonight... was the most difficult thing I've done and have done a lot already, this really tried my patience. I feel like this is maybe a stupid post, but I'm having a hard time deciding how these handle bars are meant to sit on the bike? No matter how...

I think I'll order this one today, the harness they sell is tempting too being that this one has been messed with so much. I'm still trying to get it started I'll use the one I bought and leave the 12v regulator on the bike for now I guess. The product page itself makes it sound like it does...

Hello, Working on a project and have gone through and replaced most of the electrical parts. Wasn't getting spark on the left side and have been dealing with that... I was going to replace the regulator this evening when my father found this absolute disaster with the wiring. It's so awful I...