Father Son 75 CB200T Rise From the Ruins

teazer said:
Exactly.

We have one here that Pete Fisher at Powroll modified for us a few years ago. The only picture I have appears to be analogue, so that gives you some idea how long that project has been stalled :-(

Crank is easy to rebuild and rods are available with new pins. I think they were Honda 90 OHC single but don't quote me on that.
There are a few 180 motors around and few of them work any better than stock. They did lighten wallets by a chunk, so maybe that counts for something. ;-)

IMHO that motor needs thinner rings and better cam chain control but don't tell anyone I said that. It's a trade secret
Honda tried to solve it with 3 valves but the 250t didnt perform up to the 27whp that honda claimed. It had almost the same stroke as our little gals and had an 11k redline. I wonder if that six speed will fit in lucky? The road test said they only got it up to 82. We are greenhorns but because of y'all we are at 82mph in 4th gear. We are getting closer and you don't know how much we appreciate y'all.

Are there chrome rings on that fox we are chasing? Talley hoooooo!
 

Attachments

  • image.jpg
    image.jpg
    196.3 KB · Views: 726
  • image.jpg
    image.jpg
    65.2 KB · Views: 664
  • image.jpg
    image.jpg
    19.1 KB · Views: 656
What about a deep freeze to handle the heat? http://www.aera.org/engine-professional/cryogenics/

Valve guides?
Valves?
Valve springs?
Etc?
 
We used to Cryo our Aprillia RS250 race parts and they seemed to last long enough. It wasn't my money we were spending, but it didn't seem like a great return on investment to me.

Three valve motors should offer advantages in terms of low lift flow but not necessarily a lot at the top end. 4 valves and shim under bucket tappets are the way to go with Titanium valves. Look at an FZR400. If they can be tuned to make around 72HP at 16,000 with 400cc, surely they would make +/- 36 on our 200cc twins.....Just sayin'........................

5 into 4 was easy. 6 into 5 is more of a challenge. Thinks smaller or two strokes....Speed up the clutch if the torque load is too high......
 
teazer said:
We used to Cryo our Aprillia RS250 race parts and they seemed to last long enough. It wasn't my money we were spending, but it didn't seem like a great return on investment to me.

Three valve motors should offer advantages in terms of low lift flow but not necessarily a lot at the top end. 4 valves and shim under bucket tappets are the way to go with Titanium valves. Look at an FZR400. If they can be tuned to make around 72HP at 16,000 with 400cc, surely they would make +/- 36 on our 200cc twins.....Just sayin'........................

5 into 4 was easy. 6 into 5 is more of a challenge. Thinks smaller or two strokes....Speed up the clutch if the torque load is too high......
Heat, heat, heat...the four letter word that we have been thinking about. How to handle the heat. I figured if anyone on this forum had done cryro it would be you. We were thinking on a smaller scale like the valve guides. It is amazing how much there is to learn. It is overwhelming at times. However most of the time i know we are acting like Christopher Columbus thinking we are discovering the new world while the Indians who paved the path just stand by patiently... Waiting for us to catch up. :)

We talked to Zach at r/d today. The valve kit is very reasonable with titanium retainer, keepers, springs, and shim. May just spring for the complete kit. Still doing research on the other springs.

Question. Wouldn't the valve length hold the installed height of the valve springs at 1.18" even if the springs were slightly longer than the stock springs?
 
Yes, but then the springs are compressed more than is necessary and is placing undue strain on your valve train.
 
Dear Chris, Queen Isabella and the Spanish Court awaits your return with good news of the Americas.

Meanwhile back at the infernal combustion engine,.....................

The answer could be YES or it could be NO, depending on how we interpret the question. The distance between the spring seat in the head and the underside of the valve collar is fixed, yes. But depending on a number of factors it may not be 1.18". As Matt mentioned, fitting longer or shorter springs doesn't change the gap that they will be squeezed into, but it will change the compressed force - or spring load.

A longer spring compressed into the same installed height will have higher static and peak lift loads than a shorter spring in the same slot.

If a valve seat (in the chamber) is cut deeper, the whole valve will rise slightly in the head and the fitted length will be longer. Fit a larger diameter valve and the opposite happens, fitted length drops, unless the longer valve has the keeper grooves ground higher up the stem.

So the issues here are: were the installed heights close to spec to begin with, what was the effect of any machining, and what installed length is ideal for the replacement springs.

We install a valve and collar and keepers and a super light spring to hold it all in place and then measure the gap between top and bottom collars. If that gap is too large, slip a shim under the spring.

It's the old paradox: In the long run all fixed elements are variable and all variables are fixed. In our case, valve spring installed height remains constant - until we change something that affects it.:-)
 
Sonreir said:
Yes, but then the springs are compressed more than is necessary and is placing undue strain on your valve train.
The cb175 valve spring has a free height of 31.8mm/1.25" an install height of 29.5mm/1.164" and a spring load of 28.27# @ 6.2mm/.244" valve lift it has 98.569#
The cb200 has a free height 1.37" an install height of 1.18" and a spring seat load of 40# and no # at max lift info was in the manual.

They share the same valve sizes.

The 175 and 200 have the same cam height. They have different durations
220/230 for the 175 and 220/225 for the 200 -exhaust intake respectively.

So they have the same valve lift. So did we find another reason why the 175 was able to wind higher with a lower valve spring load?
 
In Mr. Bells book he has a chart for sizing inlet valves. Does anyone know how he came up with the numbers?
 

Attachments

  • image.jpg
    image.jpg
    683 KB · Views: 315
There are two ways to size a valve. Calculate flow velocity through the orifice for a given motor size.

You can also measure the port and size each section appropriately and the valve will end up being a certain size that would allow for a perfect port shape but it may flow more or less than the motor needs.

Or you say screw all of that let's check the head on a flow bench and see how much it flows at different valve lifts and then compare that graph with the cam lift curve that you plotted and then you look at how much air the engine needs to make a certain amount of power using software like the Engine Expert.

The reality is that our old bikes have imperfect ports and all the theory in the world doesn't give us all the answers in the real world and that's where good old empirical work comes in a.k.a. Trial and error.

In the case of a CB200, port geometry suggests we need a larger valve or lots of Devcon to get a perfect shape, but flow numbers suggest that a stock valve is already flowing more than the motor can use. Both are correct, but only one path leads to more power at a given engine size.
 
Texasstar said:
The cb175 valve spring has a free height of 31.8mm/1.25" an install height of 29.5mm/1.164" and a spring load of 28.27# @ 6.2mm/.244" valve lift it has 98.569#
The cb200 has a free height 1.37" an install height of 1.18" and a spring seat load of 40# and no # at max lift info was in the manual.

They share the same valve sizes.

The 175 and 200 have the same cam height. They have different durations
220/230 for the 175 and 220/225 for the 200 -exhaust intake respectively.

So they have the same valve lift. So did we find another reason why the 175 was able to wind higher with a lower valve spring load?

Or is the valve too small for a larger engine ?

Or is the milder exhaust can restricting the 200?

Or is it the extra friction from those big heavy pistons and rings?

Or is it ring flutter on the 200?
 
Or is it below-piston pumping losses?

Or is it the 2mm reduction in carburetor diameter?

The list goes on... ;)
 
Ok OK ok....lol Y'all knew what I meant...just one more piece of the puzzle :) do y'all have the formula to figure out what our valve intake size should be?????
 
It's a non-trivial calculation.

You'll need to know your cam timing, lift, and rocker arm ratios. At that point you can model a function to represent your valve lift at any given degree of rotation and then integrate (yes, calculus) to arrive at the total open valve area of a rotation of the cam. Now go back and adjust your model to account for flow around the valve stem and any shrouding that's occurring (this is called the mean valve flow coefficient and is almost always an approximation). At this point, you use your integrated value to determine the total flow for your intake valve(s), which is then averaged over 720° of rotation.

I think the point Rich was trying to make is that it's impossible to have knowledge of all the variables affecting the flow around any given intake valve, which is why all the numbers you will ever find on this topic are ranges and/or starting points. Empirical tests beat beat out bench calculations any day of the week.

Here's a decent article on the subject, though:
http://www.hemrickperformance.com/Pages/valve.aspx

And a decent online calculator:
http://www.wallaceracing.com/machcalc.php
 
This was from a post on Hondatwins.com Team Hansen 450 upgrades in 2008...
http://www.hondatwins.net/forum/viewtopic.php?f=56&t=574

"So, slow night in a motel - thought I would post some communications from Terry Naughton regarding prices of various 450 options offered there.

Warning - not for the faint of heart, or those with light wallets.
But if you truly want to get serious with your 450, you can't do much better.
Terry won Daytona this year on this stuff, so....
Turn your 450 into a 60 hp brute that will do some serious damage in its class on the track, or rudely awake some crotch rockets on the street.........


Start::
Racing the past into the future



MOTOR PARTS & ACCESSORIES cb450 & 500t

1. 218 gram 74mm forged slipper piston kits…$480.00.
stock Honda cast pistons ( always lighter ) weigh 230 grams.

2. 75.5mm forged super lightweight slipper piston kits…$500.00.

3. Bore any cb450 stock cylinders…$130.00

4. Special SS ringed composite head gaskits 74mm & 75.5mm…$68.00

5. Complete 5mm drop in coil spring kits ( guides.base plates
inner & outer coil springs. 5mm Intake & exhaust SS valves. Titanium
retainers. Keepers. Lash caps automotive style valve seals, This kit
contains 40 pieces needed to convert from torsion bars to coil springs.
.
6. 7mm SS hi-flow – nailhead intake valves ( the best )…$75.00.

7. 7mm SS inconel exhaust valves ( highest high temp SS made )…$75.00.

8. Lightened- balanced- polished- knifedged crankshaft…$1,200.00.

9. Special 4340 shot peened steel race rods…$1,200.00.

10. Special Titanium race rods ( 40% ) lighter…$2,000.00.

11. Top end oil kit ( braided hose AN fittings etc. )…$475.00.

12. Paper cartridge oil filter…$550.00.

13. Modified rocker box cover ( better oil flow to cam lobes )…$48.00.

14. Special close ratio 6 speed gearbox & undercut gears…$2,650.00.

15. Complete Dry clutch kit & 4 vane oil pump…$2,950.00.

16. Full race pre-jetted Mikuni carbs 36mm throttle included…$550.00.

17. Special velocity stacks for Mikuni’s…$210.00.

18. Keihin cr35mm & 37mm carbs with push-pull throttle…$850.00.

19. Cylinder modified for dual spark plugs…$400.00.

20. Hi-Energy magneto with adjustable mounting plate…$750.00.

21. Special hi-lift race cams, hot street cams also available…$450.00.

22. Adjustable sprockets installed on race cams…$400.00.

23. Special full race cam chain…$75.00.

24. Stock cam bearings converted to roller & needle bearings in customers.
Part, cams & cam bearing surface turned down…$400.00.

25. Complete cylinder head porting, camshafts & Titanium valves
installed with beryllium valve seats, exhaust ports welded & raised
intake ports epoxied floors…POR.

26. Special rocker box EPOXY red coating, for faster oil return…$25.00.
This coating is included in all special cylinder head work done.


Team Hansen prefers to build Full Race Motors based on the cb450, we
Consider this to be a better revving motor, when combined with Titanium
Valves and Titanium rods, and a lightened, balanced crankshaft, will
Produce a superior revving engine.


Complete stage 3 - $12,500.00…stage 2 - $11,500.00…stage 1- $10,500.00





Team Hansen Honda LLC.
Race Engine Build Specifications

HONDA CB 450-500T
STAGE 3 FULL RACE

The building of a race engine includes many time consuming tasks which effect the cost, performance and delivery to the customer. An engine can be built to meet the highest performance criteria from street mild to full race. Team Hansen Honda strives to provide customers with an improved ultra - high performance engine with an optimized cost to performance ratio for their customers. Team Hansen Honda has the experience to offer the improved high performance of the Honda 450 twin engine, which has resulted in a record of success on the track with numerous first place wins leading to seven Vintage National Championships on Honda twins.

A complete improved high performance engine will be provided as specified. Team Hansen Honda will drain the oil of a stock engine obtained from local sources. This engine will be dismantled with a complete inspection and verification of the components to assure that a race worthy engine can be built. Inspection of components include, but are not limited to, good engine crank, stock overhead cam cores, rocker arms, cam bearings, good cylinder head with no pitting in combustion area, good spark plug threads, etc. If necessary, additional stock engines will be dismantled to provide the customer the BEST components possible for their race engine. Engine case will be bead blasted outside for appearance unless otherwise specified by the customer. All Phillips head screws will be replaced with stainless steel Allen head screws during the assembly of the race engine.

These motors when tuned correctly will produce 58 to 60 horsepower


STAGE 3 Bottom End Specifications:

• Clean, disassemble and inspect crank shaft and verify all tolerances
• Polish Honda stock rods, 4340 steel race rods, full titanium race rods available per customer request
• Inspect transmission, inspect shifting dogs, verify smooth shifting operation
• Inspect clutch assembly, install new race clutch plates, discs and springs.
• Inspect shift shaft for good splines
• Inspect detent arm for proper operation
• Modify stock oil push rod for improved oil pump operation
• Build and install plate for dry side case for magneto install
• Remove kick starter assembly and plug hole
• Remove engine starter motor and plug hole


STAGE 3 Cylinder Specifications:

• Install new aluminum forged high compression race pistons
74mm 498 cc
75.5mm 510cc
Customer choice of engine size. Race pistons will be special coated for improved performance and life of the part
• Bore lower case cylinder opening for larger iron cylinder sleeves for 75.5mm
• For 75.5mm, install new larger cylinder sleeves for new pistons & hone
For 74mm, Install new larger cylinder sleeves for new pistons & hone
• Deck cylinder as required for proper squish area


STAGE 3 Cylinder Head Specifications: This is where the horsepower is made !

• High performance porting of the stock head. CFM charts indicating flow improvements on this motors’ specific cylinder head will be provided
• Deck head as required to assure flatness
• Machine head for dual plug (two spark plugs per cylinder)
• Install new spark plugs (two per cylinder)
• Install new valve seats (Berillium for titanium valve install)
• Install new silicon bronze valve guides and seals
• Install two new 7mm titanium intake valves (oversize with lash caps)
• Install two new 7mm titanium exhaust vales with lash caps
• Install new dual spring race valve spring set, lash caps, titanium retainers
• Install new race spec cam chain
• Inspect stock cam chain tensioner (replace if necessary or as required)
• Inspect rocker arms, polish and lighten. Replace as required
• Install NEW rubber boots for carburetors (boots will be ported to fit the head)
• Machine combustion area for O-ring for copper gasket
• Install COPPER head gasket
• Install VERY SPCIAL hi-performance race cams with needle bearing ends (cam has been lightened with factory tachometer drive removed which requires the use of an electronic tachometer for engine RPM)
• Machine 4 cam bearings, install needle bearings
• Install new adjustable CAM SPROCKET for adjustment to degree cams for maximum performance & horse power

STAGE 3 Magneto & Ignition System Specifications:
• Install new Magneto in dry sided engine case
• Install adjustable timing bracket with Magneto for adjustments
• We Provide Magneto ignition coils for dual plug set up (installation of coils by customer)

ALL STAGES 1 2 3 - Additional Cost High Performance Engine Options:
Additional services for engine top performance include:

• Mikuni carburetors bored to hi- performance specifications and fitted to intake boots, velocity stacks for increased air flow.
• All internals modified
• Jet needle, needle jet, slow jet, idle jet, i.e. all parts for hi-performance, installed for maximum horse power and flexibility

• Transmissions:

o Honda 5 speed close ratio street gear box
o Full racing 5 speed close ratio gear box ( all new gears only )
o Full racing 6 speed close ratio gear box ( all new shaft, selector drum
etc. everything new )

• Honda dry clutch set up:
o Anodized coated aluminum dry clutch side cover
o Aluminum basket
o Safety cover
o 4 vane rotary oil pump ( high volumes of oil supplied )
o really helps save the cams and rocker arms.
o must use the full race CR 6 speed gearbox.

• Full race rods for Honda 450-500T
o 4340 steel bushed H beam rods ( just like carillo, but better )
o Full titanium bushed non-stretch rods, aluminum bronze bushed,

• 40% lighter than stock rods. Special plasma sprayed sides
prevent galling that occurs when Ti rubs with steel.
we use 6% aluminum & 4 % vanadium in the rod with






AMS - 5844, 280,000 PSI rod bolts. The highest rated Ti rods available.

• Full race Crankshaft - the stock Honda crankshaft, when disassembled
can be lightened & fully polished to a mirror finish ( helps remove oil from the crank Throws at high RPM ), then fully balanced with rods & pistons
( this makes for a very smooth running motor & more precise throttle control )

• Install paper cartridge oil filter to replace stock slinger filter
with option for top end oil supply & oil cooler.
This is required when installing the top-end oil kit.

The top end oil kit must have the existing oil galleries in
the lower case and upper cylinder head BLOCKED, permitting
only cool oil coming into the cam’s.

• Top end oil supply kit, with black braided hose& #6 anodized
aluminum fittings.

• Special internal engine coatings, for reduced HEAT producing & horsepower robbing friction, ( these coatings help produce higher horsepower & more reliable race motors, from piston, ceramic, etc ), I have seen an honest 8 to 10 % increase in horsepower using coatings.

• REM PROCESSING of internal parts ( this process is discussed in another area
of Team Hansen performance engine information )

• Color options for engine side case’s, dark green ( magnesium )
Black, dark gray.

• Cylinder head color ( black ) high temp.

• Customers also have the option to have a Full race motor
fully run – in before being delivered.

Customers know full well that, since these motors are 40 plus years old
we cannot furnish any warranty. But we offer help in future tuning , set-up
or repair that might occur.

• Shipping & crating for out of state customers and out of country customers:
Full race motors will be shipped in a wooden crate, bolted down with metal supports.


STAGE 2 European SPEC CB 450 – 500T

The Stage 2 engine is designed and built to meet the displacement limits of the
EUROPEAN market. The STAGE 2 engine offers significant improved performance
Over the STAGE 1, providing maximum performance from the CB450 engine within
The European guidelines. Significantly more time to build with increased cost makes this the easy choice in its class. The STAGE 2 includes a professionally ported extremely modified cylinder head, dual spark plugs per cylinder, dual plug coils, magneto ignition, conversion from torsion bars to coil valve springs, new stainless
Steel intake & exhaust valves, new forged race pistons, and a very high lift race cam.
To be used for street or race efforts. This engine can be placed in that CB450 Café Racer project bike, but ready to blow away the rest of the street racers. A track day with this engine in your Café Racer will impress your friends and create a lot of interest & questions. To meet the European rules, and American café racers this motor has 498 cc displacement limit.

STAGE 2 Bottom End Specifications :

• Inspect crank and verify tolerances
• Inspect transmission, verify smooth operation
• Install oil pump drive
• Install stall paper oil filter
• Install a new clutch ( disc, plates & springs )
• Install new base gasket
• Inspect shifter shaft for good splines
• Inspect detent arm for proper operation
• Install new Magneto ignition
• Install adjustable timing plate for ignition adjustment
• Machine engine case for dry siding Magneto components
• Remove and plug kick starter & electric starter holes
With aluminum plugs

Additional services include undercutting stock transmission gears
Or installation of CR 6 speed transmission.

STAGE 2 Bottom End Specifications:

• Inspect crank and verify tolerances
• Inspect transmission, verify smooth shifting
• Install oil pump bronze drive bushing
• Install paper oil filter
• Install new clutch, discs & plates with springs

• Install new race quality base gasket
• Inspect shifting shaft for good splines,
• Inspect detent arm for proper operation
• Install new magneto ignition including timing plate for adjustment
• Machine engine case for dry side magneto ignition components
• Remove & plug kick starter mechanism & starter hole


STAGE 2 Cylinder Specifications:

• Install new cylinder sleeves
• Bore engine cases for larger sleeves
• Bore and hone new cylinder sleeves for 74 mm
Forged racing pistons
• O-Ring cylinder head
• Install new O-Ring copper head gasket
• Deck cylinder as required

Additional Services Include ceramic coated pistons


STAGE 2 Cylinder Head Specifications:

• Professional porting of head (CFM Charts indicating improvement will be provided)
• Deck head as required
• Grind new valve seats
• Replace valve guides with silicon bronze
• Modify head for use of high performance inner & outer coil valve springs
with titanium retainers, steel keepers & 5.5 mm lash caps
• Provide stainless steel 5.5 mm stem diameter high flow intake & exhaust valves, standard size







STAGE 1 CB 450 – 500T Street – Café Racer

The STAGE 1 engine is a great introduction into the world of Honda CB450 improved
performance engines. The cost to performance ratio is very good, resulting in more fun on the track with improved performance over the stock motor. The STAGE 1 Engine is also a great engine to place a Honda 450 Café Racer or a home built project. The STAGE 2 includes a mild porting of the head, single spark plug per cylinder, conversion from torsion bars to valve springs, new stainless steel intake & exhaust valves, new forged pistons and a mild cam shaft that can be used for street or race efforts. The engine will perform well riding on the street or taking it to the track for track day. Honda stock carburetors may be used with this engine, but for better performance and tuning, check out our specially modified Mikuni carburetors.


STAGE 1 Bottom End Specification:

• Inspect crank & verify tolerances
• Inspect transmission, verify smooth shifting
• Inspect clutch assembly
• Install new clutch discs & plates& springs
• Install new high performance base gasket
• Inspect shifter shaft for good splines
• Inspect detent arm for proper operation

Additional services include undercut gears for stock transmission, new Magneto ignition including timing plate for adjustment, removal of kick start mechanism and plugging the hole, including the starter hole.


STAGE 1 Cylinder Specifications:

• New forged race pistons
• Bore & hone stock cylinder sleeves for new pistons
• O-ring cylinder top
• Install new copper head gasket
• Deck cylinder as required


STAGE 1 Cylinder Head Specification:

• Single plug head used, mild porting to increase air flow. CFM charts will be provided
• Deck head as required
• Inspect valve seats. Grind as required
• Inspect valve guides. Replace with silicon bronze
• Modify head for conversion from torsion bars to coil valve springs
• Provide new stainless steel intake & exhaust valves
• Provide valve springs, lash caps, retainers and keepers
• Inspect cam chain. Replace as required
• Inspect cam followers. Replace as required
• Inspect cam bearings. Replace as required
• Install new rubber boots for carburetors
• Install copper head gasket
• Install mild performance intake & exhaust cams




PRICE ON REQUEST"
 
Sonreir said:
It's a non-trivial calculation.

You'll need to know your cam timing, lift, and rocker arm ratios. At that point you can model a function to represent your valve lift at any given degree of rotation and then integrate (yes, calculus) to arrive at the total open valve area of a rotation of the cam. Now go back and adjust your model to account for flow around the valve stem and any shrouding that's occurring (this is called the mean valve flow coefficient and is almost always an approximation). At this point, you use your integrated value to determine the total flow for your intake valve(s), which is then averaged over 720° of rotation.

I think the point Rich was trying to make is that it's impossible to have knowledge of all the variables affecting the flow around any given intake valve, which is why all the numbers you will ever find on this topic are ranges and/or starting points. Empirical tests beat beat out bench calculations any day of the week.

Here's a decent article on the subject, though:
http://www.hemrickperformance.com/Pages/valve.aspx

And a decent online calculator:
http://www.wallaceracing.com/machcalc.php
Thanks Sonreir. No wonder I couldn't find anything other than .6(bore) lol...or 52-54% of bore. When I read that chapter between the lines I think I heard Mr. Bell say, " oh heck I am just going to give them a chart." Lol

As always we are off the chart...;) I am handing it to the mathematician in the family to see if she can figure out a pattern.
 
Look for valve area of 30-33% of bore area if possible on a 4 valve motor and whatever you can get away with on a 2 valve. 2 valves are limited to what will physically fit inside the head and that's really the limiting factor. After that, increasing bore size meets the law of diminishing returns at some point and you trade revs for torque.

You can cram in slightly larger valves by changing valve angles but I wouldn't on that motor unless I welded up the chamber and ports and started again.

It's all a series of design compromises and each theoretical approach will give a different answer and physical dimensions will ultimately dictate what works and what won't and you work around those constraints.

Good example are Titanium valves which are lighter and therefore desirable. BUT on an OHC motor rocker arm side thrusts tend to cause valves to rub on the guides and that can lead to bent valves. With enough spare parts and limitless funds anything is possible, but there are not enough hours in the day to try everything.

Look at the formulae for relative sizes of different parts of the port first and determine what you would ideally like to change.

Then look at what will fit. You will immediately be faced with two contrary indicators - valve sizes that fit and carb sizes that make any sense. Decide on a compromise that works and then have teh head gas flowed to see what each port flows. See how the exhaust flows at higher lifts because if that's restricted, it will remain constipated and bloated.

Then have the ports modified as best you can to what you decided it should be like and then have it flowed again and see what worked and what didn't.

If you want it to rev though, that's in the piston-bore area that attention must be paid. And the crank can be polished to remove oil which sticks like you cannot believe, to that rotating mass.

Look at gas analysis on the dyno and if unburned HC levels are high, focus on squish and swirl to improve flame propagation rates and fuel droplet size. Think about the emulsion tubes and air jets in the carbs to get the best emulsification and smallest droplets.

And keep having fun.
 
Fun! U are in the middle of our fun. Zeke was wrenching on Victoria last night and said, "ah the smell of marvel mystery oil...dad that brings back good memories." Lol I get texts like this at work...

G.k Chesterton said, "angels can fly because they take themselves lightly! Satan fell because of his gravity." :)
 

Attachments

  • image.jpg
    image.jpg
    46.8 KB · Views: 760
:) I hope my youngest son gets on ounce of the interest in the mechanics of things as your boy does. This stuff always puts a big grin on my face.
 
JohnGoFast said:
:) I hope my youngest son gets on ounce of the interest in the mechanics of things as your boy does. This stuff always puts a big grin on my face.
bud I lucked out as dad...all my kids have their own interests and the best thing we have done as parents is to make them our own...
 
Sonreir said:
It's a non-trivial calculation.

You'll need to know your cam timing, lift, and rocker arm ratios. At that point you can model a function to represent your valve lift at any given degree of rotation and then integrate (yes, calculus) to arrive at the total open valve area of a rotation of the cam. Now go back and adjust your model to account for flow around the valve stem and any shrouding that's occurring (this is called the mean valve flow coefficient and is almost always an approximation). At this point, you use your integrated value to determine the total flow for your intake valve(s), which is then averaged over 720° of rotation.

I think the point Rich was trying to make is that it's impossible to have knowledge of all the variables affecting the flow around any given intake valve, which is why all the numbers you will ever find on this topic are ranges and/or starting points. Empirical tests beat beat out bench calculations any day of the week.

Here's a decent article on the subject, though:
http://www.hemrickperformance.com/Pages/valve.aspx

And a decent online calculator:
http://www.wallaceracing.com/machcalc.php
thank you!!!
This is beautiful work. Thank goodness it was one of the pictures left in your pictorial string! Will you give us a run down on how it was done? Do we need to worry about the direction we do it?
 

Attachments

  • image.jpg
    image.jpg
    219.6 KB · Views: 301
Back
Top Bottom