Father Son 75 CB200T Rise From the Ruins

After almost 100 pages & how many hours ... I'd hope that lucky was a tad ahead of stock. Nice to have your own 1/4 mile.
 
simo said:
After almost 100 pages & how many hours ... I'd hope that lucky was a tad ahead of stock. Nice to have your own 1/4 mile.
yes it is :) we also have a huge circuit mapped out.

Can't wait to see how Lucky performs with 50 more pages ;)
 
Most gas does, yeah (at least here in OR). You can get pure gas (non-ethanol) at a few places.

www.pure-gas.org
 
Sonreir said:
Most gas does, yeah (at least here in OR). You can get pure gas (non-ethanol) at a few places.

www.pure-gas.org
we are gonna try some c-12 once we get back from barber and drill the floats out to 2mm...have you tried any of these fuels http://www.vpracingfuels.com/motoroadracing.html?
 
I have not. It would be interesting to see if they live up to their claims. I bet someone with some dyno time could figure it out. :D
 
Sonreir said:
I have not. It would be interesting to see if they live up to their claims. I bet someone with some dyno time could figure it out. :D
will do. Sonreir have you researched ceramic wheel bearings?
 
An obvious improvement, but I'd be hesitant to chalk it up just to bearing materials without further investigation. I suspect there could be more at play.
 
Sonreir said:
An obvious improvement, but I'd be hesitant to chalk it up just to bearing materials without further investigation. I suspect there could be more at play.
If I was given that advice when I was 13...researching everything about tires /wheels at the moment. When I was 13 this kid showed up at the BMX race with bigger wheels,
Skinner tires, and a longer crank...to say the least his dad knew physics. The kid whooped us. But we thought he was just faster...

So if we can go to 19" wheels or the same circumference as a 19" wheel/tire we gain 5mph top end. I have been spending more time researching tires than wheels. Mass matters on the salt and lighter is not better...however it seems to me that the weight from inside to out would matter..so a heavier wheel with a lighter tire might make a difference.

Oh and that kid had sealed bearings...
 
19" wheels gains you a theoretical 5mph on the top end, but does your bike have the power to push it? Are you currently able to hit redline in top gear?
 
Sonreir said:
19" wheels gains you a theoretical 5mph on the top end, but does your bike have the power to push it? Are you currently able to hit redline in top gear?
not without the fairing. No problem in 4th gear...don't have enough road for 5th gear...yet :) Zeke is 80lbs lighter though and hit 75 in our little father son drag race. We may need to pull the 5th gear out of the 175 and put it in the 200
 
Going to fewer teeth on the rear sprocket and/or more teeth on the front sprocket will help, too.

If you can find the .96 fifth gear, swap over to a 19" wheel, and go with a 15/35 front/rear sprocket ratio, I put you at 101 mph in 5th gear at 10,000 RPM.
 
Texasstar said:
Will going down to 17's help with that 5th gear by reducing the mass?

It's not a mass reduction that does it, it's a mechanical advantage for the engine. Smaller wheels are easier for the engine to turn. You'll gain acceleration at the expense of top speed.
 
Sonreir said:
Going to fewer teeth on the rear sprocket and/or more teeth on the front sprocket will help, too.

If you can find the .96 fifth gear, swap over to a 19" wheel, and go with a 15/35 front/rear sprocket ratio, I put you at 101 mph in 5th gear at 10,000 RPM.
we are running a 17/35 at the moment...4th hits 80 no problem...16/35 gets its to 75 in 4th and then the dog of 5th.
 
Texasstar said:
we are running a 17/35 at the moment...4th hits 80 no problem...16/35 gets its to 75 in 4th and then the dog of 5th.

You need more power or more airstreaming, then. :)
 
Back
Top Bottom