"Patina" The 1973 CB175 Cafe Racer

It is always the little things. Have you read that 175 shop manual yet? It is a tutorial on how to build.


Sent from my iPhone using Tapatalk
 
Don't assume check and make sure your cam is installed correctly and go through the procedure to release the cam chain tensioner.. On the 200 if you install the gasket wrong and plug up you oil journal hole you fry the top of the engine


Sent from my iPhone using Tapatalk
 
xb33bsa said:
wow ;D that is good news
who was that that kept harping on about the cam hmmmmmm ? 8)
ding ding ding give this man a prize but i remember somebody saying to use a hammer? ;)


Sent from my iPhone using Tapatalk
 
Update: engine rotating freely, now no spark.

Had a spark the other day, battery died after a week and was registering 1.3 V output...not sure what to think of that. Ignition was turned off.

Now no spark so I'm trying to see if something got unplugged...could a coil fry that fast? Out comes the multimeter. Taillight and headlights work so I know I have battery power.


Sent from my iPhone using Tapatalk
 
Have everything plugged up correctly to my knowledge, but I'm getting zero resistance across my coil...

Just a reminder, I did get a spark a couple weeks ago with the plug on the engine stud, but measured the resistance across it now and I got nothing.

Shouldn't I have at least some sort of resistance?


Sent from my iPhone using Tapatalk
 
Texasstar said:
http://youtu.be/C8AXeklQHN8


Sent from my iPad using Tapatalk

This is AWESOME. I can't explain how much pleasure it gives me to get schooled by that kid. Well done, sir. Well done.

That pretty much sums it up. So you connected the lead in each plug cap? Doesn't matter which lead goes where?




Sent from my iPhone using Tapatalk
 
Texasstar said:
The resistance through the coil should be 5ohms and through the plug holes 14


Sent from my iPad using Tapatalk

Thanks!! Can you send me a link to the replacement you guys went with? And what modification it took to bolt on?


Sent from my iPhone using Tapatalk
 
a2a9aze4.jpg
dynA dc7-1 mounting
e9uhanu6.jpg



Sent from my iPhone using Tapatalk
 
I got one. But I could not mount under tank due to noise maker. But my spark is soooo much brighter than before. I mounted mine under seat
 

Attachments

  • image.jpg
    image.jpg
    294.3 KB · Views: 292
And let us not forget that a fatter bluer spark is a sure sign of more spark energy and that means it also uses more battery or generator energy, so make sure that the battery is well charged and stays that way.
 
teazer said:
And let us not forget that a fatter bluer spark is a sure sign of more spark energy and that means it also uses more battery or generator energy, so make sure that the battery is well charged and stays that way.

Cool. I have a tender I plan on keeping it plugged up to when not riding.


Sent from my iPhone using Tapatalk
 
I've never replaced or dealt with a coil before so pardon the stupid question, but is it mostly plug and play? Any extra wiring required for the Dyna?

Also, I assume leads don't come with the unit and the original ones are acceptable?


Sent from my iPhone using Tapatalk
 
Correct. It's more or less PnP but the connectors will be different. It's an easy fit, but stop and thin about the wiring and ask as you go.


As an aside, when testing a coil, it's important to tell whether the coil is bad or the leads or the plug caps. On many OEM coils the leads are sealed in place with epoxy, so the coil has to be replaced if the lead is broken internally. In some cases the lead can be replaced and re-sealed.
 
Yeah, I noticed the connections are different for sure. On that front (and I'll check with Sonreir) I think it's just a matter of changing out bullet connectors for ring terminals...

On your other point, you're saying that leads are usually sealed to the coil body itself? Or epoxied to the plugs on the other end of the connector?


Sent from my iPhone using Tapatalk
 
1sttimer said:
Yeah, I noticed the connections are different for sure. On that front (and I'll check with Sonreir) I think it's just a matter of changing out bullet connectors for ring terminals...

On your other point, you're saying that leads are usually sealed to the coil body itself? Or epoxied to the plugs on the other end of the connector?


Sent from my iPhone using Tapatalk
You will need new wires. The dyna had plug in style coil wires. I got the coil and 7mm wires off eBay as a kit. Tex runs 8mm. They are solid copper wires. I bought 5 ohm NGk spark plug boot.
 
Back
Top Bottom