"Patina" The 1973 CB175 Cafe Racer

Re: "Patina" The 1973 CB175 Cafe Racer

You have the yellow wired into the wrong side it goes on the right of the dyna


Sent from my iPad using Tapatalk
 
Re: "Patina" The 1973 CB175 Cafe Racer

Now all you need is to wire a hot to the left side of the dyna coil and you will be golden


Sent from my iPad using Tapatalk
 
Re: "Patina" The 1973 CB175 Cafe Racer


Texasstar said:
You have the yellow wired into the wrong side it goes on the right of the dyna


Sent from my iPad using Tapatalk

Ok. So I'm still missing a power wire though right? To the left side? And then move the kill to the left?
 
Re: "Patina" The 1973 CB175 Cafe Racer

You are missing power to the left side of you coil where you have the yellow wire in your picture


Sent from my iPad using Tapatalk
 
Re: "Patina" The 1973 CB175 Cafe Racer


Texasstar said:
You are missing power to the left side of you coil where you have the yellow wire in your picture


Sent from my iPad using Tapatalk

Ok, from the instructions I need to have the yellow and power on opposite sides or else I will fry it.
 
Re: "Patina" The 1973 CB175 Cafe Racer

Move the yellow to the right and disconnect the white for the moment


Sent from my iPad using Tapatalk
 
Re: "Patina" The 1973 CB175 Cafe Racer

Let me see a picture of the downside wire of your switch and a picture of your kill switch...trust me we are getting some where.


Sent from my iPad using Tapatalk
 
Re: "Patina" The 1973 CB175 Cafe Racer

We are going to connect the power wire to the left side of the coil which is the positive side and the yellow wire to the negative side. Let me pull a dyna diagram to put you at ease


Sent from my iPad using Tapatalk
 
Re: "Patina" The 1973 CB175 Cafe Racer


Texasstar said:
We are going to connect the power wire to the left side of the coil which is the positive side and the yellow wire to the negative side. Let me pull a dyna diagram to put you at ease


Sent from my iPad using Tapatalk

I'll don't have a power wire for the EI going from the switch to the coil. It's non existent in my harness.

Here is my switch.

9esu2y3y.jpg
 
Re: "Patina" The 1973 CB175 Cafe Racer

Now where is your red wire going from the switch?


Sent from my iPad using Tapatalk
 
Re: "Patina" The 1973 CB175 Cafe Racer


Texasstar said:
Now where is your red wire going from the switch?


Sent from my iPad using Tapatalk

The red power wire from the switch is going to that 8 pin connector in the EI. It terminates there. The only wires I have at all related to the coil are the white kill and yellow EI. Sounds like I need a power from the switch to the coil.
 
Re: "Patina" The 1973 CB175 Cafe Racer


1sttimer said:
The red power wire from the switch is going to that 8 pin connector in the EI. It terminates there. The only wires I have at all related to the coil are the white kill and yellow EI. Sounds like I need a power from the switch to the coil.
yes


Sent from my iPad using Tapatalk
 
Re: "Patina" The 1973 CB175 Cafe Racer


Texasstar said:
I am going to post a video for you.


Sent from my iPad using Tapatalk

You the man.

I guess the reason it wasn't designed into my harness from Sparck was because I used the stock coil and it had a power wire?
 
Re: "Patina" The 1973 CB175 Cafe Racer

Yes that was the black and white wire at the top of your coil.


Sent from my iPad using Tapatalk
 
Re: "Patina" The 1973 CB175 Cafe Racer


Texasstar said:
Yes that was the black and white wire at the top of your coil.


Sent from my iPad using Tapatalk

Makes sense.

All this still doesn't explain why I can't get continuity... :(. One step at a time I suppose.
 
Back
Top Bottom