"Patina" The 1973 CB175 Cafe Racer

Re: "Patina" The 1973 CB175 Cafe Racer

And why didn't we get a voltage reading when it was connected to the negative terminal on the coil


Sent from my iPhone using Tapatalk
 
I found tygon line for fuel and vent. Call around to small engine repair shops. Lawn mower place.
 

Attachments

  • image.jpg
    image.jpg
    171.3 KB · Views: 277
Texasstar said:
And why didn't we get a voltage reading when it was connected to the negative terminal on the coil

1sttimer said:
Good questions, and why do I have continuity now?

Hard to say without looking at it in person, but I will weigh in on a few points made over the last few pages:

1.) While it technically matters which side of the coil is positive and negative, in practice it doesn't. You can hook it up either way and it will work.

2.) White wire is definitely the power wire. Not yellow.

3.) If everything is turned on and you check for power on the negative side of the coil, you'll (probably) only get a reading if the yellow is unplugged. If everything is left plugged in, the power will flow through the yellow wire to ground and bypass your test light.
 
Re: "Patina" The 1973 CB175 Cafe Racer


Sonreir said:
Hard to say without looking at it in person, but I will weigh in on a few points made over the last few pages:

1.) While it technically matters which side of the coil is positive and negative, in practice it doesn't. You can hook it up either way and it will work.

2.) White wire is definitely the power wire. Not yellow.

3.) If everything is turned on and you check for power on the negative side of the coil, you'll (probably) only get a reading if the yellow is unplugged. If everything is left plugged in, the power will flow through the yellow wire to ground and bypass your test light.
on his continuity test...if his power was on to the negative side I understand how it wouldn't work but if his power was off why didn't the continuity test work through the resistor caps?


Sent from my iPhone using Tapatalk
 
I'd need some more details of how the test was performed.

Resistance through plugs, caps, and wires can sometimes exceed 25,000 Ohms (depending on setup). Unless a multimeter is used (and in the correct setting), you can get a false negative.
 
Re: "Patina" The 1973 CB175 Cafe Racer


Sonreir said:
I'd need some more details of how the test was performed.

Resistance through plugs, caps, and wires can sometimes exceed 25,000 Ohms (depending on setup). Unless a multimeter is used (and in the correct setting), you can get a false negative.

Multimeter was used. And a cheap one at that. I should probably fix that.
 
Re: "Patina" The 1973 CB175 Cafe Racer


Sonreir said:
Were you just using the continuity setting or reading resistance using the Ohmmeter?

I was just reading resistance through the meter. Everything read fine until I screwed the caps on.
 
10:1 odds says the meter wasn't set to read a high enough resistance level. Switch it over to the 20KΩ and see what you get.
 
Re: "Patina" The 1973 CB175 Cafe Racer


Sonreir said:
10:1 odds says the meter wasn't set to read a high enough resistance level. Switch it over to the 20KΩ and see what you get.
we addressed that


Sent from my iPhone using Tapatalk
 
Re: "Patina" The 1973 CB175 Cafe Racer


Sonreir said:
10:1 odds says the meter wasn't set to read a high enough resistance level. Switch it over to the 20KΩ and see what you get.

That's where it was set. I was reading 16500 through the wires out the coil. Nothing when I screwed the caps in.
 
Re: "Patina" The 1973 CB175 Cafe Racer

And resistance through the caps alone was fine. About 5k ohm
 
Re: "Patina" The 1973 CB175 Cafe Racer


Sonreir said:
And which two points were being used to measure the continuity?

Tried everything. Through the plug caps, nothing . Through the wires, continuity. Through the coil continuity.
 
Re: "Patina" The 1973 CB175 Cafe Racer

I just realized why fluke voltage ohm meters are called fluke


Sent from my iPhone using Tapatalk
 
Re: "Patina" The 1973 CB175 Cafe Racer

I thought I wasn't screwing it in the conductor so I tested the wire through the cap and got continuity. Not through the coil that is.
 
Re: "Patina" The 1973 CB175 Cafe Racer


Texasstar said:
I just realized why fluke voltage ohm meters are called fluke


Sent from my iPhone using Tapatalk

Mine is a Horror Freight version.
 
Re: "Patina" The 1973 CB175 Cafe Racer


Sonreir said:
And how about when to measure between the end of the plug wire and ground?

Hopefully the Guys help me remember but I don't recall measuring that one.
 
Back
Top Bottom