small CL 360 project

Looks awesome! I'd much rather see the classic black rim, silver/chrome hubs and spokes personally. Never been a fan of the black spoke/chrome rim thing...

Either way I'm sure it'll look awesome. I think and nice cream outline scallop on the tank and seat would really set it off.

Something like this bot no center fill, just the cream outline:
scallop1.jpg

I'm thinking just a single scallop on the tank and seat each side. It'll give it a nice classic look but not over do it, just a thought.
 
personally i woudl do a 2 tone... i have always liked 2 tone paint...
had a min so i used paint... ghetto i know
104535h.jpg
 
or maybe flip it and have the white areas black and the black areas white... i would also do this in cream not white.
 
Tim said:
A really nice 'non-white white' color is the Mini Pepper White.
Thanks Tim, But Ive gotta go with spray can. I really like the appliance cream that JRK has talked about.


JRK5892 said:
personally.....
had a min so i used paint... ghetto i know

LOL, My whole bike is Getto fab just turned up a notch or too. So mock up in 'paint' fits fine. Of course it would look a lot better if you could have shown it it cream, but I can still see it. Kinda grows on ya. I really like the shifter in cream. How would yo do the linkage?
 
send it to me... ill powder your linkage in trans gold when i do my brake lever... i can ship it back for free though my dads company... just a accent piece to kick it up a notch... I would also shoot your speedo cup in the cream as well
 
JRK5892 said:
send it to me... ill powder your linkage in trans gold when i do my brake lever... i can ship it back for free though my dads company... just a accent piece to kick it up a notch... I would also shoot your speedo cup in the cream as well

Very cool. Should I jsut leave the ball joint on the one end (I can remove the rubber cover) and do it as well. Also, how should I finish it (sand grit)?
 
DONT... ya i can powder over the ball joint, just pull off the rubber... dont worry about prep i will do all that, i have to polish it actually... but the roughes i will use will be a bit diff than a normal roughe cause it all needs to come out... i am using a translucent gold on them so it needs to have a shiny surface under it to get the effect we are shooting for.. should be cool though... just pack it up and send away
 
JRK5892 said:
DONT... ya i can powder over the ball joint, just pull off the rubber... dont worry about prep i will do all that, i have to polish it actually... but the roughes i will use will be a bit diff than a normal roughe cause it all needs to come out... i am using a translucent gold on them so it needs to have a shiny surface under it to get the effect we are shooting for.. should be cool though... just pack it up and send away
Sounds good but are you sure. I've got some big ole gouges in the yoke from grinding it down. I could at least hit it (deep gouges) with some 120 or something first.

Went to throw some paint (black) on the tank today. Looked real good until I got a big run. Haha. It is f'n cold. I brought the tank in and preped it. Got it and the paint all warm and took it back outside to spray (its 10* outside) Got a big ole run near the top. I thought about flooding the run to see if I could chase it out but I can was getting low and the metal was getting very cold. Guess I'll try again in about a week
 
ya man... i woudl hold off on the paint till it is warmer... it will never lay right if you dont... if you want to get the big guages out you can just get it back up to around 600 again for me... personally think stuff like that looks cool when it is all done in a trans powder... on my scoop i wire wheel'd the whole thing then did it so you can see all the scuff lines... looks awesome!
 
a couple of mock up photos done in paint. Sorry for the shitty job, but hopefully it will be enough to get an idea. I'm having trouble with photobucket so I'll try to link to my myspace. Not sure if it will work. I really like the first one. Hey JRK is there anyway to powder the shifter lever black and make the drilled indents silver? You may have to go back to the lever to get an idea of what I'm talking about (or look at the shifter in the first photo. It's kinda what I mean. For some reason it really pops).
I'm just trying to come up with some ideas before I tear this thing down, so of course it could all change as it evolves.
http://viewmorepics.myspace.com/index.cfm?fuseaction=viewImage&friendID=401349415&albumID=1213534&imageID=16706022
http://viewmorepics.myspace.com/index.cfm?fuseaction=viewImage&friendID=401349415&albumID=1213534&imageID=16706042
http://viewmorepics.myspace.com/index.cfm?fuseaction=viewImage&friendID=401349415&albumID=1213534&imageID=16706050
 
yep but that would envolve 3 hours bake time, and about 2 hours of tape... 1 for the base coat and taped, 1 for the silve after taping off the entire lever, and 1 for the clear... or we could just go all black and then re drill the holes for hte raw metal then clear... but that would dull down the black a bit
 
Damn Brother you are fast at the keyboard. You almost had to be typing that before I posted it up. Haha. Anyway, I think powder black then drill and clear would be cool. Still sounds like some work. Might be worth it bedcause looking at the mock up photos it really pops. Troy
 
personally i would go all gloss black with the holes... i think that anything else would look like it was an after thought and that is not what it was... fully powder coated looks CLEAN man... super clean... to give you an idea, here is my belt guard i did for my cafe... on your wrap... you did soak that first right? you need to soak it in water so that as it drys it gets nice and tight, if not it will fray and you will have fiberglass strands EVERYwehre whenever your riding..
dd26tu.jpg


2q00luf.jpg
 
Chain guard looks killer! I hear what you are saying about the drilled spots looking like an after thought. I agree, so I think gloss black would look real nice. Think both the brake lever and shifter should be done the same. Would epoxy hold up or should I do them in powder?

The wrap:
Did one pipe about 4 times with out the wet. I just wanted to practice before wetting. Evertime it sucked, so I was pretty nervous. I wetted them and stretched the piss out of them (got a forearm workout haha) Think it turned out pretty nice. You can't see the transition between the two pipes.
 
ha ha ha ha i know what your saying man, when i wrap pipes we use a pole as a lever and my brother always helps me do them... get a good solid wrap on them... epoxy would hold up just fine on the lever portion of them...
efrc5.jpg
 
Like your sketch. the only thing missing would be advantage of a large ass for down pressure, haha.
Think I'll just epoxy the shift and brake levers and plan to redo once in a while (would be nice to get a season out of them but I'm probably asking too much) Anyway I really appreciate the input. It's a big help.

As far as paint scheme goes I'm really digging the shiney black and chrome. It would need something to break it up a little but it looks pretty retro with the chrome rails on top of the tank. You can't see them in the photos but they really add to the retro feel.

On the tank badges, the chrome outline is pretty good but the paint inside the letters is chipping away. Can I use aircraft stripper on them or will it eat the plastic?
-Troy
 
it will eat it up... just get some steel wool... then clean it up real well... take your epoxy paint, spray some into a cap or bowl use a brush and paint the insides... good to go!
 
I've taken some time off from the bike until yesterday. (my son was just accepted at Virginia Tech Veternary school. Very hard to get in. There were some 538 out of state qualified applicants for 10 spots. So I'm pretty pumped!) Anyhow, Yesterday I finished rough in on the battery box. My son has a friend who has a plasma cutter. He hasn't seen him in a few years, but he is going to try to get in touch with him. If it works out I'm thinking of having some spades or something cut into it. It is pretty heavy and I need to shave weight. In fact it is way f'n heavy.
DSC_0547.jpg



I also finished the tabs for the electronics under the tank. This is a shot of the tabs and the factory center rib that I cut down and rewelded.
DSC_0553.jpg



I also stripped the bike down. It only took about an hour. I loaded up the frame and took it to the car wash.
DSC_0551.jpg



It doesn't look it but I spent about 5 hours on the rear wheel and dust cover. The spokes were very, very rusty. I used a wire brush on the spokes and hub. Shined them up very well. The dust cover got 400, 800, 1000, and 2000. I still need to polish it but it looks pretty kick ass already. I'll finish with rubbing compounds then wax and leave it at that. I thought about clearing the spokes and hub but decided instead to paint them with black epoxy.
DSC_0560.jpg
 
Back
Top Bottom