XS850 - Monoshock & USD Fork (pics pg 13)

Just did a little more digging on the Yamaha triples forum and I found a post about getting MKII's to work the best on a XS850...

The MKII's I have are from a XS750 (if I haven't mentioned that before). The XS100 ran the exact same carbs but in a rack of 4 (obviously). The XS850 and the XS1100 run the same piston size. So the obvious conclusion is that the guts from a XS1100 rack (needles, needle jets, pilot jet, main jet, etc.) are basically already dialed for a 850. Going to see if I can find a rack of 1100 carbs that I can gut and see what happens.
 
xb33bsa said:
you should have done this long ago and repeat the check ever time you re mount the carbs godammit >:( :D
it is possible the throttle shafts are leeking as well and this type of check can uncover it,time waster :)

Haha I agree. The carb boots are brand new so it just didn't cross my mind. I also typically work on my carbs late at night and out of respect for my neighbors don't run the bike. So my trial runs are to and from work. Not a very conducive situation to tuning I bike... I know.
 
xb33bsa said:
you should have done this long ago and repeat the check ever time you re mount the carbs godammit >:( :D
it is possible the throttle shafts are leeking as well and this type of check can uncover it,time waster :)

Indeed. Check this asap.
 
Tune-A-Fish said:
What's taking so long ::)

Haha at work now... will check it on my lunch break! You guys have me all anxious now. If this is the issue... no wasted time... just... practicing taking the carbs off and putting them back on :'(
 
No air leak. Strangely enough, the hike runs significantly better when warm. Like almost perfect.


Sent from my iPhone using Tapatalk
 
if this is the case, I would verify all the choke mechanisms are operating the same. the bike should require choke to run when cold, if not the jetting is probably too rich. But yes I probably could have mentioned the bit about xs1100 carbs.....instead of trying to grab a set of xs1100 carbs, why not buy three rebuild kits ;)

http://www.ebay.com/itm/4-X-CARBURETOR-REPAIR-REBUILD-KIT-79-Yamaha-XS1100-/221822079557?hash=item33a5a05245&vxp=mtr

that's dirt cheap!

but keep in mind, with pods and exhaust you'll likely still have to adjust jet sizes....but needle taper and such should be spot on
 
Yeah, I saw those kits. Great deal for all those parts. Might go that route.

Choke mechanism has been inspected over and over again. Bike doesn't require choke to start even when cold, and really doesn't want to run with choke. That means it's rich but leans out once the engine is warm? Doesn't explain the back firing being worse when cold though.
 
It's definitely not leaning out when warm :) It would be getting more rich, which is why it runs better when warm. BUT it still means there's some issue on the choke circuit/mixture setting. If it never really takes choke, or playing with the choke is an issue it's in/around that area of the carb.

Typical bike does NOT start without choke, or is relatively hard to start without it. When you pull the choke, proper rpm is 3000-5000rpm (depends on bike----this is an "average" rpm from the many bikes out there)

If you use the choke and you are not getting the typical number above, something is amiss. Too much fuel from mixture screws, is the general cause because when you add choke it struggles to burn all of the fuel you are forcing down it's cylinder.

Another issue I have seen when choke isn't in that RPM range, is the idle adjustment is too low/high. If the slidesbutterflies are held open (too high idle setting) there is too much air getting into the carbs and that can cause hard starting/choke not acting properly too. Best to back off idle screw completely and adjust so it JUST starts to touch the return platform. Slowly go up from there. Usually not much is needed here.

Going with TOO much fuel in the beginning...are you able to WET SET that set of carbs and see exactly where the fuel level is? I forgot to look at them again to see if yours is the PITA version or not.

Just thought I'd add more fuel to the fire on your brain :) (more to think about)
 
Okay you're right. So it makes sense that it would richen up when it gets warm and start running better. BUT, it doesn't make sense that it would start without the choke on if it was lean, which we all agree is probably the case given the popping and poor running conditions. So based on what you're saying, the bike should be running rich at idle, but based on how it's running, it's likely lean at idle.

Regardless, I'll check the plugs tonight and see what they look like. Might go one not richer on the needle for the hell of it just to see what happens at that 1/8 - 1/4 throttle range where it's having the biggest issue. I'll put the air screws in another turn on my way home and see what that does.

It's so weird to me that these air screws are backwards from others I've worked on. Keeps throwing me off. OUT is richer, IN is leaner? Guess I better go out then...
 
I know, trust me, even when writing that I'm going "ummmm what makes the MOST sense" but your bike is acting like 2 different things. A RICH bike for cold starts, but a LEAN bike while running (which REALLY doesn't make sense)

Let's see those plugs I suppose.... :) might help with SOMETHING. Pretty soon I'm just going to SEND you the damn colortune so we KNOW what the pilot/mixture at idle looks like for sure. :)

And yes, OUT is richer, IN is leaner. UNLESS....you or the last person BROKE one of your mixture screw tips and it's lodged into the carb body....check #3 mixture screw to see if that happened?
 
Checked the plugs last night and no surprise... black on left, white on right. Went ahead and bumped the needles up to the highest (richest) clip position. It actually ran BETTER this morning. Still a little popping on the right hand side. I'll check plugs again?

Forgot about the color tune... that might be a good next step.
 
treitz said:
Checked the plugs last night and no surprise... black on left, white on right. Went ahead and bumped the needles up to the highest (richest) clip position. It actually ran BETTER this morning. Still a little popping on the right hand side. I'll check plugs again?

Forgot about the color tune... that might be a good next step.

Honestly it's just odd that it goes Black, to little rich, to LEAN on down the line. Where does the fuel come in? Is the line clogged to the 3rd carb?? This one hurts my brain!
 
I think it is possessed.

MotorbikeBruno said:
Honestly it's just odd that it goes Black, to little rich, to LEAN on down the line. Where does the fuel come in? Is the line clogged to the 3rd carb?? This one hurts my brain!

The fuel comes in through a T between each carb (two fuel sources). I checked the fuel level multiple times and they all matched... so I don't think that's the source of the issue.

Edit: Still thinking I should replace the jets with the XS1100 rebuild kits just so that I know what I'm working with. Although it still can't be jet related as I've swapped the jets around between carbs. This is insanity.

The good news is that it runs really well at higher throttle levels, so what I really need to do is just go open it up on one of the awesome windy roads around here and I'll forget about all of this nonsense. Just need to get myself a little 100CC bike to ride around town :D
 
treitz said:
I think it is possessed.

The fuel comes in through a T between each carb (two fuel sources). I checked the fuel level multiple times and they all matched... so I don't think that's the source of the issue.

Edit: Still thinking I should replace the jets with the XS1100 rebuild kits just so that I know what I'm working with. Although it still can't be jet related as I've swapped the jets around between carbs. This is insanity.

The good news is that it runs really well at higher throttle levels, so what I really need to do is just go open it up on one of the awesome windy roads around here and I'll forget about all of this nonsense. Just need to get myself a little 100CC bike to ride around town :D

I'm ok with this. Make it 150cc...ha! But yeah, maybe she just needs to run and something will let loose. Who knows?
 
MotorbikeBruno said:
I'm ok with this. Make it 150cc...ha! But yeah, maybe she just needs to run and something will let loose. Who knows?

Alright. 150cc it is! My commute to work is about 1 mile of 25mph streets. Not really built for an 850...
 
I'd say go out and blast it WOT and do a plug chop (pull in clutch and kill the ignition and coast to stop, pull plugs to check color)
 
Back
Top Bottom