Search results

I got this tank, it's painted as a Yamaha tank but i'm not sure it's from a Yamaha at all. would like to know from what bike did it come

My uncle in Philly area is restoring a 1968 CB77 He is looking for a Gas Tank, but will probably need other parts as well Please PM if you got them Thanks Eran

I installed the Dan-moto Nano dashboard, it has the same functionality as the "Classic" round unit or the 180 unit, but without temp sensor and fuel gauge. Everything works fine but the tachometer, i hooked it up to the negative coil terminal (positive is fixed power) but i see no reading what...

Hi, I got a danmoto speedometer and it came with a round magnet, unlike vapor or acewll that come with a magnetic bolt. can i just glue the magnet to the wheel\brake disk? would jb weld be ok? thanks Eran

Hi all, I know it's common and recommended to add relays for the headlight and ignition coils, is also needed for the tail light, brake light and horn? thanks Eran

I modified the frame allot but made a small calculation error and now a standard uni pod filter (3" length) doesn't fit behind my carbs - well it can fit if i squeeze the end a little. is there a decent filter that's about 2.5" long and fits over a 2" throat? what other options do i have...

I need ideas on how to arrange all the electric components + wires under my seat. I dont have a "bum stop" seat just a flat seat with some space under it, in which i need to install: anti gravity 4 cell battery big r\r Suzuki ignitor starter relay fuse block 2 Relays Flasher unit it's about 2"...

I'm going to simplify the wiring on my bike and moving all components to a "under the seat pan tray" do all the components need to be grounded thru their chasis (Igniter,starter relay, R\R etc..) thanks Eran btw the bike is a 84 Suzuki GSX 400 (no points)

Got a pair of Brand new JT Sprockets for Suzuki GS 16T Front 45T Rear 35$ including shipping from 19025 (USA) Eran

Hi, My GSX400 has 18" wheels, the stock tires are 3.0x18 front and 3.5x18 rear. since i'm making it sort of scrambler i wish to use amore "off road" tire, but most of the come only at 21" front. i found a pair of kenda rear tire that comes in 3.50x18 and 4.0x18, i think they will fit on my...

Got some brand new parts for Suzuki GS JT front sprocket 16T JT rear sprocket 45T 59600-45841 PISTON/CUP SET 59667-49460 DIAPHRAGM 69689-49300 SCREW For MC Cover (pair) Parts are brand new and sealed. Sprockets 45$ shipped in conus M/C parts 35$ shipped in conus Eran

hey all, I'm looking for tires, for 18" rim. I want them to look "knobee" but most of my riding will be on the road with maybe some mild dirt roads etc. the bike is a suzuki gsx400 the front tire is 90/90-18 and the rear is 110/90-18 any suggestions? thanks Eran

I want to paint my forks satin black, I used a wire wheel to remove the old paint and they are dull and kinda "scratched". what do i need to do to get them ready for paint? i'll use automotive paint (there's a place that makes aerosols with ppg paint ready for use), do i need a primer on the...

Hi All, in my build (Suzuki GSX400) i will have a flat seat and no "Cafe racer" hump. i plan on using an anti gravity 4 cell battery. question is will i be able to put all electronics (starter relay,R/R,ignitor,turn signal relay .fuse box and battery) under the seat pan on a tray welded to the...

If my carb intake size is 50mm (OD) do i need 50mm pods or a tad smaller? thanks Eran

Hi I need to renew my bikes loom and was thinking about using this type of sleeving. with shrink tube at the ends. what diameter do i need for the main loom and for the "Branches"? I thought 20mm for the main loom and 10mm for the smaller ones - does that sounds about right? Thanks Eran

HI, I need a front disk for my bike, any GS 400/425/450 or GN 250 will fit. Looking for one in good condition with lot's of "meat" Thanks Eran

I saw this bike on pipeburn and fell in love. i want to make my GSX 400 very much like it. It has an amazing seat that i would like to mimic. any ideas of how it attaches so perfectly and how the sides of the seat look so square? Thanks Eran

On my Suzuki GSX 400 that I'm rebuilding, i have taken the motor out but at the moment not going to completely take it apart. i took off the side covers and will remove the head cover, so the covers will be easy to paint. but my concern is how to paint the rest of the motor, to be more precise...

Hi all, I wish to use a lithium battery on my bike, for saving space and weight. I know from my RC hobby that they need a special charger, so how do they work on bikes? Eran