Follow along with the video below to see how to install our site as a web app on your home screen.
Note: This feature currently requires accessing the site using the built-in Safari browser.
We noticed you are blocking ads. DO THE TON only works with community supporters. Most are active members of the site with small businesses. Please consider disabling your ad blocking tool and checking out the businesses that help keep our site up and free.
Hello All!
I'm trying to put together a CB350 I have, but it has a couple bent valves. I'm looking to buy a set of straight valves so I can get this sucker back on the road.
Thanks!
Stephen
So I have a cb175 that will only idle at ~2000rpm if I have both idle adjustment screws on the carbs dialed all the way in. With both all the way in, the idle is stable at 2000rpm, but if I back either side out, or both sides out just a little and it'll die pretty quick (within 15 secs). Can...
I'm putting the top end of my CB175 all back together and have a quick question about the timing chain adjuster/plunger.
I know you compress the plunger into the head and hold it with the set screw. Once the head is reinstalled you loosen the set screw and the plunger pops out and presses...
So I've seen this gauge all over the internet:
http://www.amazon.com/CARBURETOR-FLOAT-GAUGE-MIKUNI-KAWASAKI/dp/B001PLDUVE/ref=sr_1_1?ie=UTF8&s=miscellaneous&qid=1296720653&sr=1-1
But does anyone know of one that is in metric units of measurement as opposed to in inches? Sure I could easily...
I've got a bike that has a turn signal switch on the handle bars, and new LED turn signals on each corner, but nothing in between.
I've picked up a 3 prong EP35 flasher, which should be able to handle the LED turn signals no problem. What I'm having a problem with is how to wire this all up...
So, this is sort of a weird non-cafe type question, but I know there are a lot of hardcore builders on here.
I'm working on an engine swap (KX125 into Aprilia RS50 frame) and the 2 stroke engine is pretty narrow compared to the frame. I need to extend the transmission lever straight out from...
So I've noticed that when its hot out and my CB350F gets nice and hot such as sitting at a light, it will start to puff some smoke out the breather vent on the valve cover. Is this normal? What would cause this? Blow by on the rings or?
Thanks
Stephen
I'm looking for a CB350 camshaft, in good condition. I also need the two bolts that attach the timing chain sprocket to the camshaft. What the heck, I'll take the camshaft + sprocket + two bolts if you got em!
Thanks!
Stephen
So I'm doing a head gasket on my CB350T, tore down the top end easy enough, but I'm having difficulty figuring out how to setup the timing chain.
First of all, the manual never states when to re-install the chain tensioner, at what point does this need to go back on? After I've got the...
Recently picked up a 72 CB350 and want to lower it ~2 inches. I assume for the rear I can just purchase some slightly shorter shocks, but was a little stumped with the front. The tops of the shocks bolt to the upper triple tree, so I cant just slip the shocks up to lower it. Any ideas? I've...
All the OEM sites I've found just show 'out of stock' for the jets. I think I need to go one size larger then stock on the main jet. Where do you guys buy em?
Thanks!
Stephen
So I'm in the process of rebuilding (new pistons + rings) a CB175 engine, but I'm stuck on re-installing the timing chain.
The manual says:
"Align the 'T' timing mark on the generator to the timing index mark."
So finding the T timing mark on the generator is easy enough, but I have no idea...
I've been searching the forum and internet for a small turn signal switch to use for my CB350F, but have come up empty handed. I was hoping you guys could help me out and let me know what you are all using?
Thanks!
Stephen
Hey,
I need the cam chain clip that holds the master link in the chain for a CB175. Or do yoiu know if this is something that can be purchased separately somewhere?
Thanks for your help!
Stephen.
Hmm, I don't think that hole is supposed to be there. Bummer...
So is there any specific places anyone can recommend for buying NOS oversized pistons and rings for a CB175 along with a gasket kit?
At the moment I'm thinking about just replacing the pistons with NOS oversized ones, And while...
So what is the proper method for doing a compression test on a CB175? Using electric/kick start? Throttle Open/Closed? And what are good numbers?
With the throttle fully open and the electric starter, I'm getting ~120psi in both sides.
With the throttle fully closed and electric starter, I...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.