Follow along with the video below to see how to install our site as a web app on your home screen.
Note: This feature currently requires accessing the site using the built-in Safari browser.
We noticed you are blocking ads. DO THE TON only works with community supporters. Most are active members of the site with small businesses. Please consider disabling your ad blocking tool and checking out the businesses that help keep our site up and free.
Got the Cb360 out for the first ride of the season a couple of days ago and the bike started up fine, let it idle for a bit to warm up, bike was in neutral (unless the neutral light was lying to me). dropped it into first, let out the clutch and the bike jerked and stalled. tried shifting...
just got my raask rearsets, and they were supposed to be a bolt on application, but it seems they are a bit more complicated than that.
the instructions that came with are almost useless. the bolts that hold them on to where the passenger pegs used to be are too long and bump up against the...
the pictures were taken in 1968, it looks like a small honda parallel twin, very overloaded. and were taken during a cross country trip that was the basis of one of the most important books of the 20th century. extra points if you can name the man in the picture and or the book that was written...
tired of fooling around with my keihins and thinking about going with a set of mikuni vm 32's from ebay. just wondering if any of you have done this swap and what experiences you have had with it.
installation issues
reliability issues
performance
compatibility
can you get velocity stacks for...
DRILL PRESS:
A tall upright machine useful for suddenly snatching
flat metal bar stock out of your hands so that it smacks you in the chest
and flings your beer across the room, denting the freshly-painted project
which you had carefully set in the corner where nothing could get to it.
WIRE...
bike is running rich even though everything tells me it 'should' be running lean. plugs black and sooty, running with 2 into 1 aftermarket pipes and k&N pods, original keihin carbs recently cleaned, jet sizes 100 and 68 if i remember correctly. I think those are stock. pls correct me if I am...
so in the process of getting the mistress ready to flog once again, i pulled the plug wire on the left side to check on spark strength ( i have a nifty tool for this, its an inline tester that shows the spark while the bike is running). spark is a bit weak but my battery is a bit low so i...
looking for information about the small brass screw that sits about an inch above the pilot screw on the keihin carb. one of mine worked its way loose and fell out. bike bandit didn't have it, and i'm not really sure what it does. anyone know what it does, and where i might get one?
thanks
TP
somehow it worked its way loose, I don't even know what this one does, but the small brass (i think) screw that sits about an inch above the pilot screw on my cb 360 w/kehin carbs. it worked its way loose and fell out. I tried bike bandit but they don't have it, and its not included in a carb...
Im in the process of building a new battery box for my cb360 using a smaller gel cell battery. location is in the same place but a much smaller footprint. and it will clean up the open space quite a bit. allowing for some sweet velocity stacks I ordered from slingshot cycles. I noticed that all...
after noting that with a fully charged battery (12.5 volts) I was only getting 9.4 volts at the coils I have decided to do the $50.00 coil repower mod found here
http://www.wgcarbs.com/index.php?option=com_content&task=view&id=12&Itemid=26
but it describes a kawasaki setup. I have a honda...
so i've cleaned the carbs checked for air leaks all seems well, and when cold she will idle for days. but when i'm on the road and she is all warmed up, whenever i close the throttle she just dies. i'm runnng keihin carbs on her for now but when i get a few bucks i plan on switching on over to...
trying to get my cb360 running right hoping to get it done this weekend, hoping a fellow rider in the baltimore washington area can help out. my carbs are out of sync and cant find a carb synch tool locally. i can order one but it wont be here for at lest a week. looking to borrow one and...
can someone point me in the right direction. i turned the idle adjustment screw the wrong way (i know, i'm an idiot) and the cable fell out I cant figure out where it (the end with the spring) goes back in. does anyone have a picture or a diagram of where it attaches to the carb assembly? I want...
I bought this bike pretty much done, it passes the 10 foot test. but it has issues and I'm gonna take it the rest of the way. I'm going to need some help if you will indulge me, as i'm new with this type of bike and as i've come in at the tail end of a lot of mods already, well, its a mess under...
new to the cafe thing but been riding for years. just picked up this sweet little firecracker to fool around with. I know i'm not building her from scratch, so i won't have the street cred of most of you. but she does have some gremlins to deal with. a few electrical problems, possibly bad...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.