Father Son 75 CB200T Rise From the Ruins

teazer said:
You could try a pair of 2" long rubber tubes in place of those incredibly cute Pollini stacks just to see if it's an inlet tract resonance issue.

Considering longer manifolds (between carb and hear) could also bear investigation. If you're considering a hotter cam, some additional distance between carbs and valves will help prevent double carburation.
 
Attach clear tube to your drain plug and secure it to the side of the float bowl. This way you can clearly spot the fuel dropping. If the bowls don't have the drain nipple, then it uses the screw type. Take a screw that fits in there, bore it out and attach a brass pipe in the center of it so it has the same function as the nipple. But I'm sure you already know this :P

Should you reinforce that frame?

2010-08-01_013312_Float_level_adjustment.jpg
 
Something wrong with that diagram... Fuel level typically should be around 3mm below the gasket surface.

Gas flow in an exhaust pipe is never what you might expect. I have seen a large rag sucked into an exhaust and it did not come back out. On the dyno the sniffer proboscis needs to be way up inside the pipe or else it suck in air and reads artificially lean. In this case there appear to be several things going on with several changes in direction in the A:F curve that need more investigation.

The long tube suggestion is a quick and dirty idea to see if inlet resonant length is a problem. You are correct that a more accurate approach is to change the main jet to valve distance. This may provide some insight into which way to go next.

Red has aded a nice picture to illustrate what I suggested, but make sure that the top of that tube is very high and very secure to avoid any possibility of spilling gas onto a hot exhaust. I'd investigate that first because that's what the graphs suggest is the issue - falling fuel level.
 
teazer said:
Something wrong with that diagram... Fuel level typically should be around 3mm below the gasket surface.

Typically. Some carbs that only give specifications for float height turn out to have a level equal to the gasket. Set a CB450k to 22mm as specified and it will be 0mm from gasket.
 
Thanks guys...wow are we learning from y'all! We did more riding than wrenchin today 'cause it was just to pretty not to. The interesting thing about the vm carbs is it appears the bowls are smaller than the keihins. We have the 20mm keihins on the bench being cleaned and we are going to put them on with cb750 velocity stacks. We will port the petcock. Check the flow with a clear tube and go back to the dyno. We can check the flow easier with the keihins because the jet is not in the drain plug like the mikunis.

Redliner as far as the frame goes we will address that down the line when we weld the frame mounts for the fairing.

Sonreir I think our calculations for an intake length are going to come into play and also the devcon f because it looks like the exhaust is out flowing the intake.

The short velocity stacks maybe pretty but they maybe better for the track than a top speed attempt...

Teazer...A big yes on Joe Cocker's song. Zeke and I saw Joe, Zztop, and Tom Petty together. Joe opened and raised the bar for the show...as do our friends.
 
Texasstar said:
Sonreir I think our calculations for an intake length are going to come into play and also the devcon f because it looks like the exhaust is out flowing the intake.

That's an interesting situation in which to find yourself. I don't have a great deal of knowledge about the CB200s, but I'm going to assume (dangerous, I know) that the engineers and Honda used a similar game plan in their engines of the era. What I'm trying to say is that it's the exhaust ports that flow poorly on the 360 and tend to be the bottleneck. I would expect the 200 to follow suit.

Have you setup a poor man's flow bench yet?
 
She looks like a Delta lady to me. Stock CB200 head flows around 44 CFM at 0.150 -0.250" lift compared to 47 - 70 on the intakes. With a low lift cam flows are similar and because of the higher exhaust pressure differential it has too much port volume. Try a larger cam.... You want lift rather than duration but don't tell anyone. It's a secret.

Longer inlets are better up to around 10k or so IIRC.
 
Sonreir said:
That's an interesting situation in which to find yourself. I don't have a great deal of knowledge about the CB200s, but I'm going to assume (dangerous, I know) that the engineers and Honda used a similar game plan in their engines of the era. What I'm trying to say is that it's the exhaust ports that flow poorly on the 360 and tend to be the bottleneck. I would expect the 200 to follow suit.

Have you setup a poor man's flow bench yet?
not yet but you can feel it when you ride and hearit when you hug her tank..she is a groin giggle up to 9k with the short velocity stacks on the mikunis...there is a difference in the intake port velocities between the two carbs...there is a dramatic difference in sound. The mikunis are Mae West in a red dress as she says, "An ounce of performance is worth pounds of promises." The 18mm Keihins roar like a Delta Lady...http://youtu.be/o93jTKhil9Y

We are gonna see what the 20mm keihins sound like...
 
Eh, excuse me for asking something that I'm almost certain isn't necessary, but how are you synchronizing your carbs? Are you checking each time that the cables are perfectly synchronized too?
 
Redliner said:
Eh, excuse me for asking something that I'm almost certain isn't necessary, but how are you synchronizing your carbs? Are you checking each time that the cables are perfectly synchronized too?

And another head slapper from me.... The exhaust gaskets?
 
http://www.examiner.com/article/vintage-honda-keihin-carburetors
The Keihin carburetor has been a fixture on Honda Motorcycles since the late 1950s. Before that , many Japanese bike manufacturers had used licensed copies of Amal carburetors on many models. Keihin developed a fairly standardized carburetor design, which was applied to most Honda models from the 50cc C110 Sports Cub to the mighty CB750 Fours. The popular 250-305cc models from the 1960s carried either 22mm or 26mm versions on nearly 250,000 motorcycles. The history of these two sizes can fill a small booklet, though, as Honda applied fuel metering theories differently in seemingly similar applications.

The 22mm carburetor has the most to talk about here, though, thus it is the subject of today’s topic. The first units are described as “round bowl” designs, where the float chambers had somewhat rounded corners and used rounded floats, as well. See illustrations for comparisons.

Initially, the 22mm carburetor was used on the 250-305cc Dream models, which were low-performance bikes with a 360 degree crankshaft firing order. Other than a few minor jet/needle changes, the carbs were the same for either model.

In 1961, the CB72-77 Super Sport models were released and two 22mm carburetors were used on the 250cc edition. A big design departure, however was use of a “power jet” system, to enrich the mixture above 6,000 rpms. This required additional external castings to provide the installation of fuel and air correction jets. Clean air needed to be drawn into the metering circuits, so a small extension tube was created, which was connected to the air filter fitting, using a small rubber tube. Changing the sizes of the fuel and air correction jets allowed for fine tuning of the high-speed circuits, which was critical in an engine that was turning 9,000 rpms back then.

Ironically, when the new 250cc Scrambler was introduced in 1962, the same 22mm carburetors were used, but the power jet circuit castings were all left un-machined and just the main jet size was increased to fuel the high speed circuits. Throughout production of both models, each had its own carburetor designs, despite the similarity in the engine configurations. By 1965, however, carburetors switched from round bowl to square bowl design on CA/CB models, but for some reason all Scramblers had square bowl units, dating back to 1962.

The 26mm carburetors of the CB/CL77s were offered as round bowl and square bowl designs, through the years, but the early castings still offered power jet extensions and protrusions, which were never used. Finally, in the final year of production, the excess material was removed, so the carburetor bodies have a much smoother appearance. Eventually, the 26mm carburetors were modified to become 28mm-sized for the early CB750 K0 models (4 cable style) and also revamped into a 24mm pair, fitted to the later SL350 models.
 
So we live in the home of the hawks...and yesterday as we were riding we saw a hawk dive next to us for the kill. That honda cb/cl72 carb is a hawk :)
 
Had a bunch of CB72s and 77s over the years - or should that be a flock?

No 22mm carbs in my pile though. We use 26mm CB77 carbs on a 181cc CL175 motor and they work just fine, but smaller is probably better on the street. I always thought that 24mm would be perfect - not too big and not too small but your bike is Lucky, not Goldielocks. Maybe it's a Kestrel.

Back in the day the hot ticket for CB160s was a pair of Keihin 22mm carbs on Webco manifolds. And that was on a little 160cc motor.



When will the cam get there?
 
Texasstar said:
copper exhaust gaskets are in...but we may need some back pressure now...

Back pressure in the exhaust system in a myth. You don't want a pressurized exhaust system. You want a system flows as well as possible while still ensuring that velocities are maintained.

The confusion probably arises because the usual method for setting exhaust velocities is by changing the ID of the pipe. Smaller pipes create greater pressure and therefore greater gas velocities. Exhaust running at the correct velocity will generally exhibit better flow characteristics than one this is flowing too quickly (too much pressure) or too slowly.

You can't just jam crap in the muffler and call it back pressure though. It's velocities you're after, not the pressure.
 
Sonreir said:
Back pressure in the exhaust system in a myth. You don't want a pressurized exhaust system. You want a system flows as well as possible while still ensuring that velocities are maintained.

The confusion probably arises because the usual method for setting exhaust velocities is by changing the ID of the pipe. Smaller pipes create greater pressure and therefore greater gas velocities. Exhaust running at the correct velocity will generally exhibit better flow characteristics than one this is flowing too quickly (too much pressure) or too slowly.

You can't just jam crap in the muffler and call it back pressure though. It's velocities you're after, not the pressure.
thanks Sonreir ..what is your analysis of what the cl pipes are doin to our performance after the porting. The interesting thing about the cl pipes is they appear to be one size but they are not. The header is a thicker tubing just like the cb headers and where there are welded to the thinner wall pipe the ID gets larger. According to our calculation the ID of the header is correct for a high speed run whereas if we were road racing lucky we would need a smaller ID header.
 
I don't believe that many of the decisions around Honda's exhausts from the 1970s took performance into consideration all that much.

The double and triple walled pipes you'll find as the stock offerings are heavy and probably exist just to keep the pipes from "bluing". It's not uncommon to change the ID of the pipe as progresses toward the muffler (similar concept as wave tuning the intake), but more modern designs and development favor flow over pulse tuning. Keep the pipe as straight as possible and at a constant diameter (unless collecting the headers into a single exhaust pipe, which does produce a performance benefit when done correctly).
 
I'll propose the question again; what are your opinions on exhaust cut-outs to vary exhaust velocity at different RPM's? On an application like this, it would be cable-operated.
 
teazer said:
Had a bunch of CB72s and 77s over the years - or should that be a flock?

No 22mm carbs in my pile though. We use 26mm CB77 carbs on a 181cc CL175 motor and they work just fine, but smaller is probably better on the street. I always thought that 24mm would be perfect - not too big and not too small but your bike is Lucky, not Goldielocks. Maybe it's a Kestrel.

Back in the day the hot ticket for CB160s was a pair of Keihin 22mm carbs on Webco manifolds. And that was on a little 160cc motor.


When will the cam get there?
a flock of hawks...I think that would only happen in the motorcycle animal kingdom...lol...Kestrel.. :)
 
Back
Top Bottom