"Patina" The 1973 CB175 Cafe Racer

Re: "Patina" The 1973 CB175 Cafe Racer


xb33bsa said:
cool you CAN get an even smooth idle and THEN synch the slides
it is not neccesary to synch first
however you must pull the air filters to synch so it just makes sense to do it first
carry on

I'm going to pull the air filters to bottom out the slides and then move the screw back in until I see it move then stop like Mike mentioned.

I honestly don't know how to do a sync. Is it just manually adjusting the threaded nipple on the top of the carb so the slides pull evenly?
 
Re: "Patina" The 1973 CB175 Cafe Racer


cafe mike said:
Your done with that part. You went to seat and went 1-1/2 turns out right?

I did but didn't have any reason for doing so. I'll keep that one at 1.5 out or bottom it out?
 
I keep forgetting to not only explain what to do, but why. Reminds me of that exercise in school when you have to explain how to make a peanut butter and jelly sandwich. When the teacher used my instructions to make one.... Mine said take piece of bread....
Yup...... she tore of a piece..... Damn it that's not what I meant I said....
On that note I amagine when I tell you to back out that screw. You take it all the way out...
I will try harder oh thinking one
 
Re: "Patina" The 1973 CB175 Cafe Racer

1sttimer said:
I'm going to pull the air filters to bottom out the slides and then move the screw back in until I see it move then stop like Mike mentioned.

I honestly don't know how to do a sync. Is it just manually adjusting the threaded nipple on the top of the carb so the slides pull evenly?
Balance using a synchronizer .. Or exhaust pressure... I have never done the exhaust one.
 
Re: "Patina" The 1973 CB175 Cafe Racer


cafe mike said:
I keep forgetting to not only explain what to do, but why. Reminds me of that exercise in school when you have to explain how to make a peanut butter and jelly sandwich. When the teacher used my instructions to make one.... Mine said take piece of bread....
Yup...... she tore of a piece..... Damn it that's not what I meant I said....
On that note I amagine when I tell you to back out that screw. You take it all the way out...
I will try harder oh thinking one

Hey man, I'm not afraid to ask stupid questions.

I have to start somewhere. What I've found is that if I ask the stupid questions I'm more likely to get an answer than if I just pretend I know how to do things.
 
Re: "Patina" The 1973 CB175 Cafe Racer

1sttimer said:
I did but didn't have any reason for doing so. I'll keep that one at 1.5 out or bottom it out?
Yes 1 1/4 or 1 1/2 is fine. That adjust the amount of air mixes with the fuel. Lean/rich setting... Minor...major adjustments are made with jets and needle.
 
Re: "Patina" The 1973 CB175 Cafe Racer

1sttimer said:
Hey man, I'm not afraid to ask stupid questions.

I have to start somewhere. What I've found is that if I ask the stupid questions I'm more likely to get an answer than if I just pretend I know how to do things.
I hate people who do things without asking why.
Your good by me.
 
Re: "Patina" The 1973 CB175 Cafe Racer

So it makes sense that the revs took off if the idle screw was almost all the way in...hopefully backing that out (lowering the slide) will get me in the ballpark.
 
use 2 (one in each carb)excactly same size,MEASURE THEM WITH CALIPERS !, popsicle sticks on EDGE inserted gently so that they hold up the slides
they needs to be fully under the slide not just at the cutaway
use a light and look in make sure the are evenly seated on both sides basically they will be propped up by the needle and the bottom edge of stick flat to the floor of the throat of carb
now when you very slowly open the throttle the sticks should be released from the slides EVENLY at the same time the sticks are being used like a feeler guage kinda
just use one or the other cable adjusters at the top of carb to get this right
 
Re: "Patina" The 1973 CB175 Cafe Racer

1sttimer said:
So it makes sense that the revs took off if the idle screw was almost all the way in...hopefully backing that out (lowering the slide) will get me in the ballpark.
You got it. Are you working on the bike now???
 
Re: "Patina" The 1973 CB175 Cafe Racer

cafe mike said:
Look at some you tube videos of bench synchronizing... And synchronizing
i have seen some wrong ones on youtube
follow my method
one idiot had popsicle sticks layed in flatways,sticking out at at an angle ::)
 
Manual says
 

Attachments

  • image.jpg
    image.jpg
    202.3 KB · Views: 291
  • image.jpg
    image.jpg
    97 KB · Views: 283
  • image.jpg
    image.jpg
    266.8 KB · Views: 286
  • image.jpg
    image.jpg
    250.6 KB · Views: 285
that synchronizing procedure in the manual does not do shit ::) of course they rise and fall together they both are hooked to the throttle
we are talking about getting them synched for airflow it must be done as i layed out
the only other way to do it would be on a flow bech
or to adjust the idle screws first for the excact same slide opening using say a drillbit on each side
but the stick method is easy and fool proof
 
xb33bsa said:
that synchronizing procedure in the manual does not do shit ::) of course they rise and fall together they both are hooked to the throttle
we are talking about getting them synched for airflow it must be done as i layed out
the only other way to do it would be on a flow bech
or to adjust the idle screws first for the excact same slide opening using say a drillbit on each side
I agree with that sync. Method. It's so bad, it's funny.
 
Re: "Patina" The 1973 CB175 Cafe Racer

I want to try one of these
3u8e3e2u.jpg



Sent from my iPhone using Tapatalk
 
Back
Top Bottom