Search results

I have 2 NEW/unused Milwaukee M18 Red Lithium XC 18V batteries(retail $120). I'm looking for $80each or $150 for both. $80ea/$150both OBO. http://www.homedepot.com/h_d1/N-5yc1v/R-100672227/h_d2/ProductDisplay?langId=-1&storeId=10051&catalogId=10053 I also have 2 new/unused Milwaukee M12...

I have just graduated from UAB and I am 23 and will be moving to begin my career.I plan to begin training June 15 in one city or the other for the next year. My income will be 32k + bonus/benefit for the next year or so. I have the options of Tupelo, MS(1 year then Memphis) or Sarasota, FL(1...

Ok so i have a 76 cb750 motor w/ everything(in parts), and I have a complete 78 motor that I fixed and had running great. replaced the head, using the 76 head,because i had a problem with a valve, set the timing wrong and blew the rings on the #4. 78 rings are difficult to find and pricey when...

Bike: 1978 CB750K On my number 4 i started blowing gas and losing power. I tested my compression, and got nothing. Pull the intake valve cover off to find that the nut has spun off of the tappet adjusting screw. It some where in the head!!!. The problem I am facing here is retrieving the nut...

So i have not had any problems from my cb750k until i bought gas the otherday. I wasnt thinking and put cheap gas in my bike. I have been running 93 octane like i do in all my bikes. The tank was 1/3 full when i filled it up. On the way back home from my 2 hr ride i noticed i was loosing power...

I have looked through the forum to find this answer and came up with nothing. I recently purchased a Barnett clutch kit ( friction p's, steel p's, and springs) everything is great until i put the clutch lifter plate back on. I think im tightening it down to much or not enough since i cant seem...

Ok so i was having a seal problem, and just got the new one, no more seal problem. Now i am having a problem when i bleed the brakes the pads just lock down on the disk. I changed the master cylinder , so maybe thats the problem. yet i have pressure i attached a pic , maybe i have the banjo and...

WTF. my slow jets on my cb750 keep vibrating off! whats the deal? (background: 78 motor, 76 carbs, 4 into 1 exhaust, pod filters) i just upped the mains to 130 and 3/4 to full is good. I have turned the slows out 1.5 turns and and it wont idle the carbs have been thoroughly cleaned and the...

i want to run a copper fuel line on my 76 cb750 and wondering if anyone else has done it? any quick instructions. I have an idea of how im going to do it but if you have already done it let me know what you did

so i have been trying to do rear sets on the cheap, i even started a thread, that didnt turn out so well, Im my continual effort to nickel and dime my life ive spent a while trying to find something. I figure If people stumble upon a deal you can post it... just wanted share wat ive found with...

Ok so Im rewiring my 76 cb750k, I am losing all buttons on the bars and changing to a standard auto ignition switch and adding a 3 way switch for the head light (low, off, high). I drew up a diagram but not sure about a few things: 1st the headlight: im assuming the headlight is grounded by...

Ok so i have my throttle line and its to long, and i need to cut it down. I have crimped ends on lines for my bicycle before but i also wasnt stopping a 500lb bike. BAckground info: have a cb750 and using only 1 line instead of two. I have searched everywhere( google, here, etc.) Maybe a DIY...

Ok so i got this bike and had wirinng issues so i was tryign to kickstart it and i was slowly pushing the bike over and it came to stop so and couldnt push it anymore. I was afraid it was vacumm locked so i backed the motor up at the points and it was fun and took the plugs out... well i fixed...

I decided to loose the instruments except speedo on my cb750k and the igniton and controls i had were junk. how do i wire up a 3 point ignition? I know its simple but i cant seem to do the brain work right now.. its just astandard ignition switch from oreillys help me out. dixiedevil ps. i...

I sell fasteners along with manufacturing and fabrication servies( i actually work at the machine shop). Because of this, i have access to everything we would need to build some gnarly rear sets on the cheap for the members here on Do The Ton. Im interested in knowing who would be willing to...