Search results

Busted a hole through mine :/ plz get in touch with me zpallagi@gmail.com

Hey guys looking for a little help. I have a 19 inch front wheel with a 7" inch diameter hub - trying to find a brake hub to fit into the wheel - the wheel was supposively a cl350 yet when i ordered a 1972 cl350 front brake hub to fit into the wheel it was too large. I wanna avoid ordering the...

Went on a biking trip with my buddy were down in Florida. His Honda was riding perfectly and fine before this, his battery is getting drained extremely fast. Narrowed it down to the wires from the points shorting or draining the battery. Unplugged all other electrical. Just confused as to why it...

My buddy and I started this mostly restoration for this guy this winter and I wanted to show the progress so far. This bike was parked in an apartment building basement in 82' and sat there until we got our hands on it. The owner of the building let the guy were restoring it for take the bike...

Haven't seen a lot of BSA guys on here, but I thought It'd be worth a shot anyways. Purchased a BSA in november for 'discount' due to some engine noise. The bike has a little over 2000 miles. Valve clearances are set correctly, oil is getting to the top end, nothing dangling around in there...

Can anyone provide pictures how the throttle cable hooks up to to these carbs? I think I'm missing a throttle cable arm or stay plates on each carb, these carbs are really funky to me in comparison to 350s and 360s, they're like a foot away from each other :o thanks in advance

My buddy and I have been working on his bike this summer (1974 cb360). We have had an on going issue with it revving on its own and not returning to idle. To give some background: -Still happens with throttle cables disconnected -Replaced advancer springs, they snap back properly -no idle...

Here is how she sits as of yesterday. I know I need a fork brace, I am purchasing a new, smaller front tire to allow this. She is great and pulls hard but after a while she starts overheating and backfiring every two seconds. Eventually have to pull over and let her cool down till I can start...

lot of bikes in rough shape but hopefully I can salvage something that hasn't corroded too much, pretty pumped. He's also letting them go for $150 each and I'm sure I can chew him down a bit

Could this be due too a ground somewhere? I tested them at their female connectors that connect to the R/R, no voltage there, so then I went to the copper coils on the stator itself, still no AC voltage output when I had the bike running. Could it be the rotor? I tested the ohms of the rotor...

:'( Should I just order a new pair of carbs or does anyone have a way these could be taken out ? I guess this is caused by my inability to screw in CHEAP ASS replacement air screws from ebay.

Tried searching for this but couldn't find anything. Anyways, ordered 68 mains and 112 secondarys from JETRUS, the mains have a couple extra threads. I was curious if the jet being a little taller then the stock mains was ok or not, wasn't sure if this would mess up the physics of the carb or...

Have been looking for some type of fork brace for a while for my 74' CL360. I know I probably should just get a smaller tire in the front but I really just do not want to ::) . There is pretty much zero fork clearance for any type of stock front fender / fork brace on the inner sides of the...

anyone know of any shops online that sell front fenders that would fit larger wheels? thx

Was curious is anyone had any knowledge on this matter. I am at the understanding that it's important to replace some of the ancient electric parts to safely allow the use off new batteries such as a lithium-ion. I hardly know much about electronics even though sadly I took PLTW courses in high...

Is there a place to buy a plug or what options do I have to plug this hole? Thanks, Zoltan

My names zoltan, i'm 20 y/o, in the nyc/westchester area. Anyone else working on a bike or something in the area, I have a 1974 cl360 brat project I'm working on currently. We could all chill and work on bikes.. drink some brews!!

I'm located in the NYC area 1979 Honda CB 650, needs a good cleaning and new paint. -129k miles -will come with manual and key and bill of sale -No title, however I have the forms to acquire one through its-titles international service, for $280 (lame I know), however there is also the way via...

hey, my name is zoltan, I'm 21 and this is my 1974 honda cl360 build log and 74 kz400 build log. *kz400 build starts on page 10* CL360 as of 5/30/2014: BEFORE, 6/20/13 as of 4/29/14: as of 5/23/2014 I had to get the bike with my 4 door car haha... Got a ton of second...

All electrical is working properly, the bike works and runs with a kick start. However when I press the start via the electrical ignition starter, theres a hissing noise that almost sounds like some gears aren't catching towards the front of the bike. Any suggestions to what's going on will be...