Search results

Carbs should be cleaned like alwaus before going on a bike. Brand new 2-1 throttle cable. A pair of filtered velocity stacks. $140+shipping for all of it. Not sure how to attach pics from my phone.

I'm selling all of the bodywork from the CJ360. The tank comes with the petcock, it needs to be cleaned, does have some rust on the inside, and has a couple shallow dents. The seat is starting to rust on the edges where the leather wraps around but the leather is in good shape. The tail piece...

I've got a stator cover from my CL360 build that is finned like those aftermarket covers found on the CB750's and such. I've never seen one for a 360 before. The casting of the one mounting point is damaged on the inside but it never gave me an issue. I don't have the bolts anymore...

This exhaust came off a CJ360 that I started parting out. Looks to be in decent shape. The muffler isn't stock but looks better then stock in my opinion. It comes with all the brackets. $150+shipping. I'll throw in some new exhaust seals for an extra $6.

I've got a set of scrambler pipes for sale that came off my CL360. I have all the mounting hardware (except muffler mounting brackets) to go with them. No mufflers. The rear heat shield mount is broke. No heat shields. No dents. $150+shipping. I'll throw in some brand new exhaust seals...

I picked up another 360 recently. This is a CJ model and is a very complete bike even down to the OEM tool kit. Everything is in pretty good shape from what I can tell. I don't have a key so I wasn't able to hook up a battery to test the wiring harness or check the inside of the gas tank...

I put one of the later air-cooled 16 valve GS750 engines in my CL360 but the stock 32mm carbs don't fit. I've been told that 34mm carbs are a good upgrade but those also wouldn't fit. I plan to make some 2-1 intake manifolds and run two carbs to feed the four cylinders. I'm not sure what size...

I'm near Milwaukee, WI and I'm looking for 2 or 3 TITLED CL360, CJ360, or CB360 frames. Let me know what you have, it's condition, and what you want for it. Thanks, Mike

MAKE OFFERS! I want this stuff gone so I can finish my CL360 build and move on to my XS650 project. I ship as much as I safely can in USPS flat rate boxes so the shipping cost will be added when I know what exactly you want. $25 XS650 OEM seat cover in good shape $20 XS650 front rotor --...

The stock bearing spacer that goes between the wheel bearings in my front wheel has too small of an ID to fit over the larger axle I'm using. I considered having the stock part opened up a bit but the inner race of the bearings has a fillet that the spacer would ride on if it were machined...

I'm in the market for an 18" spoke front wheel from an XS650 or at least one off something similar like an xs400. If no one has the complete wheel but they can give a deal on just the disk hub I'm still interested. Cheaper is better. I'm near Milwaukee, WI if anyone local is interested in...

I'm looking for a clean straight front wheel, axle, and rotor from a CB360. The rotor surface itself can be junk (rusty or under min thickness) but I need it to still be straight. If you want something from a CL360 in trade let me know. I'm parting out two of the bikes. Thanks for looking, Mike

I've got a '74 CL360 and I'm curious as to what jet sizes I should run. I'll be running the CL360 scrambler pipes with no mufflers and I'll be running K&N pods. Any idea what jet sizes I should use? I'm new to bikes and carbs so I have no idea where to even begin with these carbs. Right now...

I already started a build thread on another forum so the following posts will just be copied and pasted from there. Because of this, some of the stuff in my posts may not make sense such as names of people and what not but at least you can see the progress. Anyway, here it goes...

I like to have the bike completely built in my head and a complete list (or as complete as possible) before I start any actual work. I find that this helps prevent any wasted time in the garage wondering what I should do next. So, here is my question... what were the stock colors offered on...

What are the differences between the two motors? Or if it will be a shorter list, what is the same? The CL360 I'll be getting has a bad motor according to the current owner but he said he will give me a CB350 motor as a parts motor. Thanks, Mike

Hey everyone! I've been lurking here for a while but finally made an account. My name is Mike, I'm 18 years old, and I live in Milwaukee, WI. I don't have a bike yet, but I will be getting a free bike soon. It's a CL360 that hasn't run in a several years and is partially dissembled. From...