Follow along with the video below to see how to install our site as a web app on your home screen.
Note: This feature currently requires accessing the site using the built-in Safari browser.
We noticed you are blocking ads. DO THE TON only works with community supporters. Most are active members of the site with small businesses. Please consider disabling your ad blocking tool and checking out the businesses that help keep our site up and free.
does anyone have a few extra 350f head studs that theyd be willing to part with? I need the 154mm long ones.
Thanks!
Robb
Sent from my XT1254 using Tapatalk
Hey all...
I'm in search of a caliper for my 73 CB350 Four project....It only needs to be rebuildable.... I know that the 360T fits as well, and I THINK there's more, but I'm not sure at this point. Anyone have one they'd be willing to part with?
Thanks!
Hey....
Trying to find a good degreaser since brake cleaner isn't any better than water these days.
Any ideas?
???
Sent from my Nexus S 4G using Tapatalk 2
Hey...
Looking to purxhase both handlebar switches for a 72-74 CB350 or 400 Four...Pm me w/info...8)
Thanks...
Robb
Sent from my Nexus S 4G using Tapatalk 2
Hey all...
I'm sitting here doing research on parts for Project CB350 F/CR, and I cannot seem to locate any handlebar switches for this model. My 1st question would be:
Does anyone have these pieces stashed away, and would you be willing to part with them?
And second:
Barroing that, are...
Hey, y'all...
Looking to buy a Emgo, Wasp, or Viper bikini fairing for my CB350 Four project......If the shield is a little beat up, that's OK, but the fairing itself needs to be undamaged.Thanks!
Robb, aka Corsair
OK guys....
I know we have some aerospace guys on here, and maybe you folks can answer this question......
I plan to drill the rear drum cover on my CB350 Four to vent some of the heat....and I thought about possibly elongating the top of each hole at a rearward angle (50-60 degrees) with the...
Was thinking about adding a mechanical oil pressure gauge to my CB350F build. Any suggestions as to brand or install tips?
Thanks!
Robb
Sent from my Nexus S 4G using Tapatalk 2
Hey, all...
Now I'm sure there's been plenty on this subject, but I gotta ask....I'm having trouble with getting the stock bearing races out of the steering head. Is the "heat & beat" method appropriate in this area of the frame? (CB350 Four)
Thanks!
Robb
Wierd question...My 1st bike, a '76 XL250 Honda was built in June '75, and my current build, a '73 CB350F was built in May '72........
Does PA still do this? (Titled as year first registered)
Robb
OK, here in PA, a lot of attention is paid to the odometer reading on any vehicle. On my CB350F build, I'm using a set a gauges purchased off an ebay buyer. The reading does not match what the seller of the frame (Ohio resident) said was on it. My thought is....since this build is going to be an...
Howdy,
I'm in the process of rebuilding the carbs on my CB350F project and I ran across this....sorry for the crappy pic, but I hope someone can tell me....
Why would they drill two holes in the drain plug of each float bowl?
Thanks!
Robb
Hey....
I wonder if anyone knows of a easy rust preventative for recently cleaned steel for storage. I'm in the middle of cleaning up some stuff on my CB350 Four build, and I may not get to them right away....
Any ideas?
Thanks in advance..
Robb
Hey there.....
I'm in the process of my 1st build, a 72 CB350 Four, and have a question about ride height....Is there a point where you get it too low? I know that scraping the pegs or exhaust is bad..... what's a good "rule of thumb" on how she sits?
Thanks,
Corsair
I have a CB200T tank that I'm using on my project.....I need to remove the trim strip tabs along the center of the tank and move the rear tank mount. Does anyone know how the factory attached them? I dont see the typical spot welds on any of the pieces....
Thanks,
Corsair
I'm probably doing this the hard way, but........here goes. My first build is a '73 CB350 Four starting with only the frame, which happens to be in great shape. I'll be buying parts & building as finances and time allow. I'm going for a classic cafe racer look, with a quarter fairing, clip-ons...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.