The piston picture I posted was off Hansen's Facebook page.teazer said:Get a new gasket made between .030 and .040mm thick.
BTW, what are those pistons or who sells them?
Thanks guys we are making a mold out of wax so seeing is believing for Zeke as we read your posts together. I read to my oldest son Lord of the Rings, The Narnia Chronicles, and The Screw Tape Letter as a child. Zeke gets y'all...teazer said:If you machine 1mm off the head, the stock "squish band" or chamfer starts to disappear and a new one has to be machined at your design angle
Teazer we just read this again and I wanted to clarify that you meant .030-.040 inches and not mm?teazer said:Hold on a moment.
CB honda twins do not have a full hemi quiescent combustion chamber. They have a narrow squish band like the pic of that EVO cross section. To get compression up, we start by machining the pistons to get the squish band to the shape/angle we want and by so doing, the crown gets to be slightly taller but only by say 0.5 -1.0mm
Step 2 is to deck the block so that the outer edge of the piston is flush with the gasket surface.
Step 3: your head ( well the bike's) goes on a milling table and the mill is centered using the barrels and dowels so that the next cut is concentric with the bore.
Step 4: machine a new squish band into the head at 1 degree larger than the piston. There must be a difference to maintain the correct mean squish velocity, but it's only around 1 degree.
Step 5: machine "some" off the head to bring the width of the squish band back to the same as the bore. If you plan on machining more than about 1mm off the head, might be best to reverse steps 4 & 5
Get a new gasket made between .030 and .040mm thick. Less than that and the piston will hit the head on the exhaust stroke. Two strokes don't but 4 strokes have that lazy exhaust stroke with no compression to cushion the blow. In general, the narrower the squish band, the tighter it can be (within limits) There is software out there to calculate MSV. Bigger engines need more squish clearance as do engines with wide squish bands.
That should leave the valves just touching pistons around TDC. You can either machine deeper pockets for the valves or recess the valves slightly into the head. We have to do both to get enough clearance.
You will also need what used to be called Fire Notch to clear the plug which will now have negative clearance to the piston.
You will also notice that the EVO head is not perfectly round but the sides of the chamber are narrower than the dimension across the valves. It's a multi-spherical design that is somewhere between a bathtub and hemi and works quite well. That can be achieved with a little weld after you take out the valve seats.
BTW, what are those pistons or who sells them?
check out Sonreir's build. http://www.dotheton.com/forum/index.php?topic=38872.120caveman592 said:Excuse me for jumping into the conversation but I have a quick question. It seems from the discussion that a hemi head is best for detonation/compression but fails in that it doesn't breathe well. So my question is would a hemi head be best design if it had something attached to it to pull air and exhaust through and make it breathe better such as a turbo or supercharger? Feel free to pm me an answer if you don't think it should be part of the thread but I didn't really know who to ask so I just put it to the good people here.
We measured from the center of the valve to the end of the velocity stack. Hopefully we will see something at 8k and 10k.Sonreir said:Depending on the wave number, they can show up as anywhere from 1% - 4% gain in power. Depends on how precise the dyno is.
Dang that is so fun! Hearing protection made it much more tolerable. I dropped a jet into the Dyno wheel and we got to see the inside of the Dyno today...clutz.teazer said:Don't thank me. Thank the engineers at Honda Central back in 1969 or so.![]()
I love the theory and spend hours researching before I go to the dyno or the strip and get real facts which don't always match the theory - usually because the theory is incomplete. It's all part of the search for knowledge.
1/4" is a big adjustment on timing but it suggests that your timing is close to what the motor wants and in the final analysis, that's what it's all about.