Follow along with the video below to see how to install our site as a web app on your home screen.
Note: This feature currently requires accessing the site using the built-in Safari browser.
We noticed you are blocking ads. DO THE TON only works with community supporters. Most are active members of the site with small businesses. Please consider disabling your ad blocking tool and checking out the businesses that help keep our site up and free.
Apart from the obvious (looks)....is there a practical and performance difference between using Pods and stacks.
Any chance the same jets would still work if I were to change to stacks?
Anyone know a source of stacks for a CB550 (Kehins)?
Found a little Honda CG110 in tidy running condition. All very original.
I can get it for next to nothing so I ask you guys...would this make a cool little project.
I am thinking a little stripped out bare frame "racer". Doubt I woud try and make it street legal.
Bring on thoughts and ideas...
I fitted a drilled front rotor to my CB 550F. (It is very shiny but oil free)
I have aftermarket brake lever and master cylinder, braided line, new pads, reconditioned and restored original calliper.
I am wondering how glossy everyones front rotor is or should be.
I am considering getting it...
Been away from here for a bit so I thought I better re introduce my self.
Shooter from Auckland New Zealand. I spent a lot of time and picked everyones brains around here while I was in the process of building this bike.
Just gave her a bit of love last weekend and got her running again...
Does anyone else smell gasoline when riding their bikes?
I have pods on my CB550. I can smell gasoline often but especially when stopped at the lights or idling after running.
No gas is leaking or overflowing. No smell with engine off.
Idle speed is about 1200 rpm.
Sorry for posting here to all (and attention Mods ) but ...
Where in this forum does one post very general questions /comments about Cafe Racers that do not fit anywhere else.?
eg: How do I gauge the performance of my Cafe CB550 SS ('76) against other CB550's?
What would be a good common...
What is the cause of carb floats sticking? (apart from being dirty or holed)
I have one on my CB550 that does this on occasion and it requires a bit of a tap to sort it out.
Bowl and float are clean.
FWIW - the carb has been rejetted.
Could it be a bent needle ?
Thinking of a small front fairing for my CB550 Cafe and wondered what it might look like. I have not seen many pix or reference to these anywhere.
BTW - I am hoping this will look cool but also be effective at highway speeds. I can feel the drag of my body and notice that headwinds do...
Has anyone ever fitted a modern caliper to a CB550 with original rotor? How did you do it ? (pix?)
I am brake obsessed but making progress.
Ditched the original Master Cylinder and lever (after installing a new kit inside it).
Have fitted a new MC that I got from Ebay ($79 USD) and now run...
CB550 '76 (but maybe '77)
I have got my self confused over what position the petcock should be set to and I am now not sure if the arrow and the markings are correct.
Confession - I ran out of gas over the weekend.
I think I must have had it set to reserve and run a whole tank through at that...
Got some things done today that had frustrated me and were unfinished parts of my finished project. I am well pleased with my efforts.
Re jetted the carbs for the pods - successful.
Sorted the key/ignition. I had pulled the whole key device to bits and had never quite got round to putting...
Here is what I am thinking of doing - putting my forks on back to front and running the callipers and rotor on the right hand side ( instead of the left).
Pictures show a Honda (Post Classic Racer) with this treatment and the front brakes work brilliantly. Theory is that the callipers at the...
CB550 '76/77
I have pulled the master cylinder to bits and I am now installing a new kit in it.
The pictures (top bits) show the old internals ordered as they came out. (I think they were wrong previously because the snap ring was out side the circlip!)
The row under that are the new bits...
Where can I get a kit to rebuild the hand brake - CB550 ?
Master cylinder has a leak at the piston where the lever contacts it. I suspect the seals are gone.
Now my bike is back on the road (and I have done 250kms of test riding on it) I have figured it needs re jetting to cope with the pod set up (as pictured).
How does one figure what jets to install - is it trial and error or is there a "formula" or trick?
Fueling seems fine up to 4000rpm...
Anyone know how to adjust the regulator to get max charge voltage?
I have a new Regulator - the old one was a bit duff and I did not feel like restoring it because of reliability issues.
Maybe the new one comes factory set? Anyone know?
I have read the manual but it is a bit confusing and I...
How do I check the charge current on my CB550. (Note: I am an electrical lkutz)
ie - where do I attach my meter? What should it read ? (13V+ I would expect)
I suspect I am not getting a charge on my just finished project. Battery seemed to flatten while I was riding. - wouldnt start on...
I guess the day that I could be on the road again (legally ) seemed so far away when I started my project many months ago and had my entire bike in bits stored in boxes and plastic bags.
Today I finished wiring in the rear indicators and stop light....
....then I took it to the place that...
I am getting so close to finished now. ;D
Just fitted the seat 1 hr ago and I really like it. Man is it comfortable and looks cool I think 8)
Engine starts and runs so sweet - sounds great and has a fantastic note. I will do a sound clip sometime for you all to hear.
I have an oil leak...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.